Page 1: Table Of Contents
Mini DV/S-VHS VIDEO CASSETTE RECORDER HR-DVS1EK STANDBY/ON PULL - OPEN INSTRUCTIONS CONTENTS SAFETY FIRST Safety Precautions ... 2 Some Do's And Don'ts ... 4 QUICK SET UP GUIDE CHECK THE CONTENTS ... 5 INSTALLATION ... 6 AUTO SET UP ... 8 T-V LINK T-V LINK Functions ...
Page 2: Safety First
In the unlikely event of the plug fuse failing be sure to replace the fuse only with an identical approved type, as originally fitted, and to replace the fuse cover. If the fuse fails again consult your nearest JVC dealer.
Page 3 ABOUT HEAD CLEANING Accumulation of dirt and other particles on the video heads may cause the playback picture to become blurred or interrupted. Be sure to contact your nearest JVC dealer if such troubles occur.
Page 4: Some Do's And Don'ts
Some Do's And Don'ts On The Safe Use Of Equipment This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. read the operating instructions before you attempt to use the equipment.
Page 5: Video Cassette Recorder
QUICK SET UP GUIDE Dear Customer, Thank you for purchasing this JVC Video Cassette Recorder. Please use this QUICK SET UP GUIDE to help you to set up your video cassette recorder. CHECK THE CONTENTS CHECK ALL THE CONTENTS SHOWN BELOW...
Page 6: Installation
INSTALLATION CONNECT VIDEO RECORDER TO TV Place the recorder on a stable, flat surface. TV Aerial Cable (not provided) ANT. IN RF OUT Back of Recorder ATTENTION: You can not use the recorder connected to your TV only with the RF cable. This is because the RF cable does not deliver signal from the recorder.
Page 7: S-Video Connection
S OUT (DV/VHS) ANT. IN AV1 OUT COMP. Y/C RF OUT S-VIDEO CONNECTION To connect to a TV with S-VIDEO/AUDIO IN connectors . . . 1– Connect the aerial, recorder and TV as per "AV CONNEC- TION" ( pg. 6). 2–...
Page 8: Auto Set Up
AUTO SET UP SET THE TUNER CHANNELS, CLOCK AND GUIDE PROGRAM NUMBERS The Auto Set Up function sets the tuner channels, clock and VIDEO Plus+ assigned Guide Program numbers automatically the first time the button on the recorder or on the remote is pressed to turn on the recorder after the mains power cord has been plugged into a mains outlet.
Page 9: Preset Download
PRESET DOWNLOAD SET THE TUNER CHANNELS BY DOWNLOADING FROM YOUR TV, CLOCK AND GUIDE PROGRAM NUMBERS When you connect the recorder and your TV via fully-wired 21-pin SCART cable ( by downloading preset data from your TV instead of using the Auto Set Up function ( recorder sets the clock and VIDEO Plus+ assigned Guide Program numbers automatically.
Page 10 If any of the above problems occur, refer to pages 64 – 66 to input station names ( stations ( "Delete A Channel"). You can also change station preset positions ( If you have any difficulty with the above procedures call the JVC Customer Service Hot Line on 0208 208 7654 QUICK SET UP GUIDE (cont.) on page 9.
Page 11: T-V Link Functions
For details, refer to the instruction manual for your TV. VCR Auto Standby You can use your TV's remote control to turn off the recorder. For details, refer to the instruction manual for your TV.
Page 12: Basic Operations
TV to automatically enter AV mode. To return the TV to TV mode after playback is complete, press TV/VCR so that the VCR indicator turns off. * Depending on the type of TV used, TV/VCR button does not always function as described above.
Page 13: Slow Motion
Still NOTES: Refer to the SHUTTLE ring illustration above as you read the following procedures. To use the remote control's JOG dial or SHUTTLE ring, press JOG/SHUTTLE first so that the button lights. Pressing the button again turns off the light. When using the JOG dial during playback on the DV deck, turn the JOG dial slowly.
Page 14: Display Mode Setting
MENU Time Code (DV Deck) During recording, a time code is recorded on the tape. This time code is used to confirm the position on the tape when playing or editing a tape. To perform Random Assemble Editing ( pg. 36), time code is necessary. NOTES: The presence of a blank (unrecorded) portion in the middle of a tape can result in misoperation.
Page 15: Recording
INFORMATION You can switch between TV mode and AV mode by pressing TV/VCR. * Depending on the type of TV used, TV/VCR button does not function as described above. TV signals being received by the recorder’s built-in tuner can be recorded onto a video tape.
Page 16 0000 RECORD Accidental erasure prevention – –:– – BASIC OPERATIONS (cont.) VHS/S-VHS To prevent accidental recording on a recorded cassette, remove its safety tab. To record on it later, cover the hole with adhesive tape. Mini DV To prevent accidental recording on a recorded cassette, set its erase protection switch to "SAVE".
Page 17: Tape Remaining Time
Record One Programme While Watching Another SELECT PRESET TO WATCH Once recording is in progress, all you need to do is to set the preset controls on the TV for the station you wish to view. The programme selected with the TV’s preset controls appears on the TV screen while the one selected with the recorder's TV PROG buttons is recorded on the tape.
Page 18: Video Plus+ Timer Programming
VIDEO Plus+ Timer Programming Before performing VIDEO Plus+ Timer Programming: Make sure that the recorder's built-in clock is set properly. Select the recording deck by pressing VHS or DV. Insert a VHS (or S-VHS) cassette with the safety tab in place, or a Mini DV cassette with the erase protection switch set to "REC".
Page 19: Timer Warning
SET TAPE SPEED Press SP/LP ( ) to set the tape speed. SET PDC MODE Press PDC to select "ON" or "OFF". If "VPS/PDC ON" is displayed on the screen or "VPS/ PDC" is lit on the display panel, PDC is set to ON. If "VPS/PDC OFF"...
Page 20: Express Timer Programming
Express Timer Programming Before performing Express Timer Programming: Make sure that the recorder's built-in clock is set properly. Select the recording deck by pressing VHS or DV. Insert a VHS (or S-VHS) cassette with the safety tab in place, or a Mini DV cassette with the erase protection switch set to "REC".
Page 21: Pdc Recording
ENTER PRESET POSITION Press TV PROG +/– to enter the preset position corresponding to the broadcasting station you wish to record. SET TAPE SPEED Press SP/LP ( ) to set the tape speed. SET PDC MODE Press PDC to select "ON" or "OFF". If "VPS/PDC ON"...
Page 22 START+/– Check, Cancel And Replace Programmes TV PROG+/– To cancel or replace a programme... NOTE: You can also check the programmes on the display panel even if the recorder's power is off (unless the recorder is in the Power Save mode however, it is not possible to cancel or replace the programmes.
Page 23: Advanced Operations
ADVANCED OPERATIONS Recording According To Tape Type Turn on the TV and select the AV mode. MENU S-VHS (Super VHS) and VHS (VHS Deck Only) Your recorder can record in either S-VHS or VHS. To record in S-VHS: Perform the steps 1 – 4 below to set "S-VHS" to "AUTO". Then, insert a cassette marked "S-VHS", the S-VHS indicator will light on the display panel.
Page 24: Playback/Recording According To Tape Characteristics
Playback/ Recording According To Tape Charac- teristics Turn on the TV and select the AV mode. RECORD PLAY RECORD MENU ADVANCED OPERATIONS (cont.) B.E.S.T. Picture System (VHS Deck Only) The B.E.S.T. (Biconditional Equalised Signal Tracking) system checks the condition of the tape in use during recording and playback, and compensates to provide the highest-possible recording and playback pictures.
Page 25: Start Recording
Recording START RECORDING Press and hold RECORD and press PLAY on the remote, or press RECORD on the recorder. DURING B.E.S.T. B.E.S.T. COMPLETE The recorder spends approximately 7 seconds assessing the condition of the tape, then begins recording. NOTES: The B.E.S.T. system works for both SP and LP modes only after a tape has been inserted and the Record mode is first initiated.
Page 26: Playback Picture Adjustment
Playback Picture Adjustment SP/LP MENU Manual Tracking (VHS Deck Only) Your video recorder is equipped with automatic tracking control. For most tapes this will automatically adjust the tracking to suit the particular tape you are playing. In some circumstances it may be necessary to make manual tracking adjustments.
Page 27 MENU Digital 3R (VHS Deck Only) Digital 3R picture system applies edge correction to the luminance signal to enhance detail. ACCESS MAIN MENU SCREEN Press MENU. ACCESS VHS MODE SET SCREEN Move the highlight bar (pointer) to "VHS MODE SET" by pressing %ﬁ, then press OK or SELECT DIGITAL 3R SET MODE...
Page 28 AUDIO PLAY Zoom (DV Deck Only) This function allows you to zoom in on a portion of the screen during playback. ZOOM DURING PLAYBACK Press T to zoom in on an image during playback. Press W to zoom out. MOVE SCREEN After zooming in, use %ﬁ...
Page 29: Looking For The Scene You Want
Looking For The Scene You Want Index Search (VHS Deck Only) Your recorder automatically marks index codes at the beginning of each recording. This function gives you quick access to any one of 9 index codes in either direction. NOTE: Before starting, make sure the recorder is in the Stop mode.
Page 30: Selecting The Sound You Want
Selecting The Sound You Want AUDIO MENU ADVANCED OPERATIONS (cont.) NOTES: Soundtrack Selection (VHS Deck) The VHS recording deck is capable of recording three soundtracks (HI-FI L, HI-FI R and NORM) and will play back the one you select. During Playback Pressing AUDIO on the remote control changes the soundtrack being played back as follows: TRACK...
Page 31 Soundtrack Selection (DV Deck) The DV recording deck is capable of recording two soundtracks (L and R) and will play back the one you select. During Playback Pressing AUDIO on the remote control changes the soundtrack being played back as follows: TRACK On-Screen Display For stereo or Bilingual tapes...
Page 32: Bilingual Programmes
AUDIO MENU ADVANCED OPERATIONS (cont.) Receiving NICAM Stereo And Bilingual Programmes Your recorder is equipped with a Digital stereo sound decoder (NICAM), making reception of stereo and bilingual broadcasts possible. When the recorder is tuned to a different station, the type of broadcast being received will be displayed on the TV screen for a few seconds.
Page 33: Picture Control
Minimizing Picture Degradation While Editing Turn on the TV and select the AV mode. MENU Advantages Of S-VHS Video Recorders You can edit from VHS to S-VHS, S-VHS to VHS, or, from S-VHS to S-VHS. From VHS to S-VHS: Record VHS playback signals in the S-VHS mode.
Page 34: Tape Dubbing
Tape Dubbing SP/LP ADVANCED OPERATIONS (cont.) Dubbing An Entire Cassette Because this recorder includes both a VHS deck and a DV deck, you can easily use it for dubbing without connecting any other equipment. NOTES: If you set the dubbing direction incorrectly, you could erase an important recording that you wanted to copy.
Page 35: Normal Dubbing
Normal Dubbing SP/LP PLAY RECORD NOTES: There may be a discrepancy of several seconds between where you intend editing to start, and where it actually starts. The on-screen display during the operation or dubbing is not recorded. When dubbing from the VHS deck to the DV deck, also set "SOUND MODE"...
Page 36: Random Assemble Editing
Random Assemble Editing PLAY ADVANCED OPERATIONS (cont.) 64-program Editing Memory (8 programmes x 8 scenes) By using the Random Assemble Editing function, you can select up to 8 scenes from a previously recorded Mini DV cassette and automatically dub them onto a VHS cassette. You can also insert Fade/Wipe effects between scenes ( changes to the video by using Playback Effects ( Random Assemble Editing is possible only when dubbing from...
Page 37 EFFECT FADE/WIPE PLAY LOCATE EDIT-OUT POINT Press PLAY to start playback. Find the point where you want the edited scene to end, then press PAUSE. Then, press IN/OUT. The edit-out point appears on the screen. USE FADE/WIPE EFFECT ON SCENE TRANSITION (IF NECESSARY) Press FADE/WIPE.
Page 38 RECORD START ADVANCED OPERATIONS (cont.) PAUSE R.A. EDIT NOTES: When Random Assemble Editing doesn't work, press beside the DUB button, then perform Random Assemble Editing again. To cancel the registered scene, press pressed, the latest regisered scene is erased. When the source tape has more than 2 identical time codes chose and a malfunction may occur.
Page 39 FADER AND WIPE MENU MENU FADER — WHITE Fade in or out with a white screen. FADER — BLACK Fade in or out with a black screen. FADER — MOSAIC Fade in or out with a full-screen mosaic effect. Fade in to a color screen from a black and white screen, or fade out from color to black and FADER —...
Page 40: Edit From A Camcorder
When using a monaural camcorder, connect its AUDIO OUT connector to the AUDIO L input connector on your recorder. When a Master Edit Control-equipped JVC camcorder is used, the camcorder is capable of controlling the recorder. Refer to the camcorder’s instruction manual for operating procedure.
Page 41 Recorder DV IN/OUT DV Cable (not provided) Player DV OUT/IN DV Camcorder (JVC camcorder only) EDIT NOTE: The signals through the DV IN/OUT connector cannot be recorded on the VHS deck, even though button is pressed. B If the camcorder has an S-VIDEO output connector...
Page 42: Edit To Or From Another Video
Edit To Or From Another Video Recorder NUMBER "0" ADVANCED OPERATIONS (cont.) You can use your video recorder as the source player or as the recording deck. TV PROG MAKE CONNECTIONS Connect the player’s 21-pin SCART connector to the recorder’s 21-pin SCART connector as illustrated on page 43.
Page 43 TV Receiver (AV mode) Player 21-pin SCART Cable (not provided) Recorder TV Receiver (AV mode) Recorder S-Video Cable (not provided) 21-pin SCART Cable (not provided) Another recorder Player NOTES: All necessary cables can be obtained from your dealer. For Y/C signal input/output, be sure to use a 21-pin SCART cable that is compatible with the Y/C signal. When you select EDIT to dub tapes in step 4, be sure to select AUTO (or NORM when B.E.S.T.
Page 44: Audio Dubbing
Audio Dubbing CD Player etc. Audio mixer Original sound AUDIO OUT NUMBER "0" PLAY NOTE: To use the DV deck as the recording deck, press DV after selecting "L-3" in step 3. ADVANCED OPERATIONS (cont.) VHS Audio Dubbing Audio dubbing replaces the normal audio sound of a previously recorded tape with a new soundtrack.
Page 45 AUDIO PLAY PAUSE STOP START DUBBING Engage the audio component's Play mode, then press PLAY to start the tape in your recorder. Audio dubbing begins at this point. " " blinks and " " is displayed on the front display panel.
Page 46: Insert Editing
Insert Editing Recorder Audio/Video signal Another recorder Player NUMBER "0" NOTES: Insert Editing is not possible with a Mini DV tape recorded in LP mode. To use the DV deck as the recording deck, press DV after selecting "L-3" in step 3. ADVANCED OPERATIONS (cont.) VHS Insert Editing Insert Editing replaces part of the recorded scene with new...
Page 47 STOP INSERT 0000 STOP NOTES: All necessary cables can be obtained from your dealer. Insert Editing cannot be performed on a VHS/S-VHS cassette that has had its record safety tab removed, or on a Mini DV cassette that has had its erase protection switch set to "SAVE". When Insert Editing is performed on a tape that has been recorded on another video recorder, the inserted portion may appear distorted.
Page 48: Av2 Select Setting
AV1 SELECT Setting Set "AV1 SELECT" to the appropriate mode depending on the type of unit connected to the rear panel AV1 IN/OUT connector of this recorder. Press MENU to access the Main Menu screen. Press %ﬁ to move the highlight bar (pointer) to "MODE SET", then press OK or Press %ﬁ...
Page 49: Remote Control Functions
NUMBER "1" STOP Remote A/B Code Switching The remote control is capable of controlling two JVC video recorders independently; one set to respond to the remote control’s A code control signals and another set to respond to B code control signals. The remote control is preset to send A code signals because your video recorder is initially set to respond to A code signals.
Page 50 Set the remote control's VCR/TV/SAT switch to TV. +/– IMPORTANT Although the provided remote control unit is compatible with JVC televisions, as well as many other models, it may not work with your TV, or in some instances, may have limited function capability. TV BRAND NAME...
Page 51 VCR/TV/SAT switch to VCR. IMPORTANT Although the provided remote control unit is compatible with JVC satellite receivers, as well as many other models, it may not work with your satellite receiver, or in some instances, may have limited function capability.
Page 52: Other Functions
Other Functions Turn on the TV and select the AV mode. MENU NOTES: When you use this recorder as the player for editing, be sure to set "O.S.D." to "OFF" before starting. During playback, the operation mode indicators may sometimes be disturbed depending on the type of tape being used.
Page 53: Power Save Mode
MENU Power Save Mode You can reduce the power consumption while the recorder is turned off. ACCESS MAIN MENU SCREEN Press MENU. ACCESS MODE SET SCREEN Press %ﬁ to move the highlight bar (pointer) to "MODE SET", then press OK or SELECT POWER SAVE MODE Press %ﬁ...
Page 54: Auto Sp Lp Timer
MENU ADVANCED OPERATIONS (cont.) Auto SP LP Timer (VHS Deck Only) If, when timer-recording in SP mode, there is not enough tape to record the entire programme, the recorder automatically switches to LP mode to allow complete recording. For Example . . . Recording a programme of 210 minutes in length onto a 180- minute tape Make sure you set "AUTO SP LP TIMER"...
Page 55: Auto Timer
PLAY MENU Auto Timer When the Auto Timer is set to ON the timer is automatically engaged when the recorder power is turned off and automati- cally disengaged when the recorder is powered back on. ACCESS MAIN MENU SCREEN Press MENU. ACCESS MODE SET SCREEN Press %ﬁ...
Page 56: Repeat Playback
STOP Retake (VHS Deck Only) You can cut out unnecessary parts of a TV programme while you're recording it. End of programme Beginning of programme Unnecessary Unnecessary Programme part part Recorded part Go back to end of programme to cut out unnecessary part ENGAGE RECORD-PAUSE MODE...
Page 57: System Connections
Timer mode, in Stop mode, recording or turned off. When the recorder is in Stop mode or recording, press TV/VCR on the remote control to turn off the VCR indicator on the display panel. In this case, be sure to set the AV1 OUT switch on the rear panel to COMP.
Page 58: Connecting To A Stereo System
Connecting To A Stereo System FM Tuner CD Player Stereo Amplifier Speaker Television ANT. IN RF OUT Back of Recorder MAKE CONNECTIONS Connect the AUDIO OUT L and R connectors on your video recorder to the AUX IN or TAPE MONITOR terminals on your stereo system's receiver or amplifier.
Page 59: Connecting To A Printer
Connecting To A Printer DV IN/OUT DV cable (not provided) To DV IN connector NUMBER "0" PLAY You can make printouts of video images by connecting the GV-DT1/GV-DT3 Digital Printer (sold separately) to the DV IN/OUT connector. Your recorder Digital printer TV PROG MAKE CONNECTIONS Connect the printer’s DV IN connector to the recorder’s...
Page 60: Connecting To A Video Titler
Connecting To A Video Titler S-VIDEO OUT AV2 IN/DECODER 21-pin SCART Cable (provided) S-Video Cable (not provided) Video Titler NUMBER "0" PLAY RECORD SYSTEM CONNECTIONS (cont.) When you edit from the DV deck to the VHS deck (or from the VHS deck to the DV deck), you can enter a title to a scene by connecting a video titler.
Page 61 PLAY RECORD START PLAYBACK Press DV or VHS for the playing deck, then press PLAY. START RECORDING Press DV or VHS for the recording deck, then press RECORD at the point from where you want to start recording. ENTER TITLE Enter a title at the point where you want the title to be displayed.
Page 62: Subsidiary Settings
Tuner Set Turn on the TV and select the AV mode. MENU Your recorder needs to memorise all necessary stations in preset positions in order to record TV programmes. Auto Channel Set automatically assigns all receivable stations in your area to call them up by using the TV PROG buttons without going through any vacant channel.
Page 63: Menu Screen
MENU VIEW CONFIRMATION SCREEN After "SCAN COMPLETED" is displayed on the screen for about 5 seconds, a Confirmation screen looking like the one on the right appears. The stations your recorder located appear on a Confirmation screen — preset positions (PR), channels (CH) and station names (ID –...
Page 64: Input Channel
NUMBER MENU Storing Channels Manually To store channels that were not stored during Auto Set Up pg. 8), Preset Download ( pg. 9) or Auto Channel Set pg. 62). ACCESS MAIN MENU Press MENU. ACCESS CONFIRMATION SCREEN Press %ﬁ to move the highlight bar (pointer) to “MANUAL CH SET”, then press OK or mation screen appears.
Page 65: Delete A Channel
Delete A Channel Perform steps 1 and 2 of "Storing Channels Manually" on page 64 to access the Confirmation screen before continuing. SELECT ITEM Press %ﬁ until the item you want to delete begins blinking. DELETE CHANNEL Press The item directly beneath the cancelled one moves up one line.
Page 66 Set Stations (A) Set station names that are registered in your recorder. Perform steps 1 and 2 of "Storing Channels Manually" on page 64 to access the Confirmation screen before continuing. SELECT ITEM Press %ﬁ until the item you want begins blinking. ACCESS MANUAL CHANNEL SET SCREEN Press OK twice.
Page 67: Tv Station And Id List
TV Station And ID List STATION NAME Anglia TV ANGL ARTE ARTE BBC Group BBC1 BBC1 BBC2 BBC2 Berlin 1 BLN1 Berlin 2 BLN2 Border TV BORD Bayern1 Bayern3 BRT1 BRT1 BRT2 BRT2 Children Ch CHLD Canal + Channel TV CHNL Central TV CNTR...
Page 68: Tv Station Channel Number Guide
TV Station Channel Number Guide Only the main stations are listed. There are in addition many relay stations, and full lists are available from the BBC and ITV. BBC1 BBC2 ITV London & South-East Bluebell Hill ... 40 Crystal Palace ... 26 Dover ...
Page 69: Clock Set
Clock Set Turn on the TV and select the AV mode. MENU Just Clock The Just Clock function provides accurate time keeping through automatic adjustments at regular intervals, by reading data from a PDC signal. The Just Clock option can be set "ON" or "OFF" at the Clock Set screen (the default setting is "ON").
Page 70: Video Plus+ Setup
VIDEO Plus+ Setup IMPORTANT Normally, Auto Set Up ( pg. 8), Preset Download ( automatically. You need to set the Guide Program Numbers manually only in the following cases. When timer-programming with VIDEO Plus+, the preset position, where the station you wish to record is received on your recorder, is not selected or when you add a channel after Auto Set Up or Auto Channel Set has taken place.
Page 71: Subsidiary Information
SUBSIDIARY INFORMATION Questions And Answers PLAYBACK Q. What happens if the end of the tape is reached during playback or search? A. The tape is automatically rewound to the beginning. Q. Can the video recorder indefinitely remain in the still mode? A.
Page 72: Troubleshooting
If you are using the AV or S-VIDEO connection, set the TV to its AV mode. Try manual tracking. ( pg. 26) Consult your JVC dealer. Engage and adjust tracking manually. pg. 26) CORRECTIVE ACTION Insert a cassette, or using adhesive tape, reseal the slot where the tab was removed.
Page 73: Timer Recording
RECORDING SYMPTOM 4. Camcorder recording is not possible. 5. Audio dubbing is not possible. 6. Monitoring the audio-dubbed sound is not possible during audio dubbing using the DV deck. 7. The programmed memory of Random Assmble Editing is disappeared. 8. When performing Tape Dubbing, the beginning of the dubbing start point is not dubbed.
Page 74: Other Problems
TIMER RECORDING SYMPTOM 7. VIDEO Plus+ does not timer-record properly. OTHER PROBLEMS SYMPTOM 1. Whistling or howling is heard from the TV during camcorder record- ing. 2. When scanning channels, some of them are skipped over. 3. The channel cannot be changed. 4.
Page 75: Index
Remote PAUSE Connector enables connection to second recorder equipped with R.A. Edit connector, or to JVC camcorder equipped with Master Edit Control, for easy editing. i VHS Button enables operations on VHS deck.
Page 76: Rear View
8 PDC Indicator lights when PDC has been engaged 9 S-VHS Indicator lights when a cassette marked S-VHS 0 VCR Indicator lights when the video recorder is in ! "Cassette Loaded" Mark lights once a cassette is @ Counter shows time elapsed since playback or # Mode shows external input mode selected (L-1, L-2 or pg.
Page 77 * VPS (Video Programme System) recording is not currently available in the U.K. and not possible with this recorder. 7 VCR Indicator lights when the video recorder is in the video mode. At this point, the TV automatically enters AV mode.
Page 78: Remote Control
TV. pg. 50 SUBSIDIARY INFORMATION (cont.) 1 VCR/TV/SAT Switch enables remote control of 2 TV/VCR Button switches connected TV's mode 3 A/B Code Button enables setting of recorder to – –:– –...
Page 79 The remote control can operate most of your video recorder's functions, as well as basic functions of TV sets and satellite receivers of JVC and other brands. Point the remote control toward the sensor window. The maximum operating distance of the remote control is about 8 m.
Page 80: Specifications
GENERAL Power requirement : AC 220 – 240 V`, 50/60 Hz Power consumption Power on : 40 W Power off : 9.0 W Temperature Operating : 5°C to 40°C Storage : –20°C to 60°C Operating position : Horizontal only Dimensions (WxHxD) : 437 x 127 x 380 mm Weight : 7.6 kg Input/Output...

JVC HR-DVS1EK Instructions Manual

Safety First

Mini DV/S-VHS

Video Cassette Recorder

Quick Set up Guide

T-V Link

Basic Operations

Advanced Operations

System Connections

Subsidiary Settings

Subsidiary Information

Specifications

Quick Links

Related Manuals for JVC HR-DVS1EK

Summary of Contents for JVC HR-DVS1EK

Table of Contents