1 - Information about the product BTAC Series READ THIS INSTRUCTION MANUAL CAREFULLY BEFORE USING THE PRODUCT. IF IN DOUBT, CONTACT YOUR QUICK ® DEALER. QUICK RESERVES THE RIGHT TO MODIFY THE TECHNICAL CHARACTERISTICS OF THE EQUIPMENT AND THE CONTENTS OF THIS MANUAL ®...
Page 6
• INVERTER speed variator for AC motors • AJ1 Thruster Command thruster control with proportional system • PAJ 1T AMC • PAJ 2T AMC proportional controls • AMC central unit for AMC system QUICK BTAC SERIES INSTALLATION AND USER’S MANUAL - REV002A...
Quick® Thrusters have been designed and constructed only for nautical use. • Do not use these appliances for other uses. • Quick® shall accept no responsibility for direct or indirect damage caused by improper use of the appliance or an • improper installation.
Page 8
MASSIMO 6 VOLTE IL Ø TUNNEL a length equal to 1.5 to 4 times the tunnel diameter. To limit losing charge, a ratio of up to 6 times the diameter can be tolerated. QUICK BTAC SERIES INSTALLATION AND USER’S MANUAL - REV002A...
• If the tunnel is near the waterline, it is advisable to fit a grating at the end of the tube. The grating must have as large a vertical mesh as possible to avoid contrasting the propeller thrust. The vertical mesh prevents the entry of most of the floating objects. QUICK BTAC SERIES INSTALLATION AND USER’S MANUAL - REV002A...
Page 10
• Fig. 7A / Fig. 7B FIG. 7A FIG. 7B Insert two O-rings into the special BTAC 250/300 BTAC B00 386 seats inside the flange. QUICK BTAC SERIES INSTALLATION AND USER’S MANUAL - REV002A...
Page 11
• FIG. 4 Grease the terminal part of the drive shaft. • FIG. 5 Insert the motor onto the elastic joint; fasten it with the 4 screws and washers provided. QUICK BTAC SERIES INSTALLATION AND USER’S MANUAL - REV002A...
Page 12
• FIG. 3 Proceed with fitting the gearleg. For further protection against the entry of water, apply silicone for nautical use around the point of contact between flange and tube. Fasten the flange using the special screws. QUICK BTAC SERIES INSTALLATION AND USER’S MANUAL - REV002A...
Page 13
• FIG. 1 After fastening the flange, turn the fitting clockwise and align it with the flange recess. • FIG. 2 Insert the Rilsan hose with oil tank into the fitting. FIG.1 FIG.2 QUICK BTAC SERIES INSTALLATION AND USER’S MANUAL - REV002A...
Page 14
• Fill the oil tank with gear oil type GL-5. > 0,2 x d WATERLINE TUNNEL CENTRE POSITION THE TUBE CORRECTLY IN ORDER TO AVOID A “SIPHON” EFFECT. THE TANK MUST ALWAYS BE IN A VERTICAL POSITION. ARIA OLIO QUICK BTAC SERIES INSTALLATION AND USER’S MANUAL - REV002A...
Page 15
• FIG. 4 Fit the motor on the gearbox and secure it to the support. • FIG. 5 Tighten the screw of the upper joint, holding it towards the gearbox. QUICK BTAC SERIES INSTALLATION AND USER’S MANUAL - REV002A...
Page 16
Secure the anodes F with screws G previously smeared with structural adhesive (such as Loctite). BTAC 513/610 ONLY WARNING: on conclusion of assembly, make sure that the propeller is exactly positioned at the central point of the tunnel. QUICK BTAC SERIES INSTALLATION AND USER’S MANUAL - REV002A...
6 - Cautions & Use 6.0 - Thruster use L’accensione avviene in conseguenza all’attivazione di un pannello di comando Quick ® Per l’uso dell’elica di manovra e l’installazione del pannello di comando fare riferimento al manuale del comando dedicato. 6.1 - Important cautions •...
7 - Maintenance BTAC Series Quick® thrusters are made in materials that are resistant to the sea environment: in any case, it is indispensable to periodically remove salt deposits that form on the outer surfaces to avoid corrosions and consequent system inefficiency.
Page 20
Separate the products for disposal in accordance with the regulations in force in your area or return the product to the seller when purchasing a new equivalent product. Local regulations may impose severe penalties for the improper disposal of this product. QUICK BTAC SERIES INSTALLATION AND USER’S MANUAL - REV002A...