D Convenient Functions For Transmit - Icom IC-7000 Instruction Manual

D Convenient functions for transmit

• Transmit quality monitor (p. 87)
)], then [F-4 O O T T H H ] to enter the mis-
➥ Push [AF(
SET
cellaneous (others) set mode. Select an item with
[F-1 ≤ ≤ ]/[F-2 ≥ ≥ ], then rotate [DIAL] to turn the
monitor function ON and OFF.
• VOX (voice operated transmit) (p. 83)
➥ While "M M - - 3 3 " is selected, push [F-1 V V O O X X ] to turn
the VOX function ON and OFF.
• Push and hold [MENU/GRP] for 1 sec. once or twice
to select the menu group M M .
• Push [MENU/GRP] momentarily one or more times
to select the menu M M - - 3 3 .
• " " appears when the VOX function is set to ON.
➥ While "M M - - 3 3 " is selected, push and hold [F-1 V V O O X X ]
for 1 sec. to enter the VOX set mode.
• Push [F-1 ≤ ≤ ]/[F-2 ≥ ≥ ] to select an item.
• Rotate [DIAL] to set the value/conditions.
D D About 5 MHz band operation (USA version only)
IC-7000 Display
Frequency*
5.33050 MHz
5.34650 MHz
5.36650 MHz
5.37150 MHz
5.40350 MHz
To assist you in operating the 5 MHz band correctly
within the rules specified by the FCC, transmission
is impossible on any 5 MHz band frequency other
than the 5 frequencies indicated in the table above.
FCC Channel
Center Frequency*
5.33200 MHz
5.34800 MHz
5.36800 MHz
5.37300 MHz
5.40500 MHz
RECEIVE AND TRANSMIT
• Speech compressor (p. 87)
➥ While "M M - - 3 3 " is selected, push [F-2 C C O O M M ] to turn
the speech compressor ON and OFF.
• " " appears when the speech compressor is set to
ON.
➥ While "M M - - 3 3 " is selected, push and hold [F-2 C C O O M M ]
for 1 sec. to enter the compression level set
mode.
• Rotate [DIAL] to adjust the compression level.
• Transmit filter width (p. 84)
➥ While "M M - - 3 3 " is selected, push [F-4 T T B B W W ] momen-
tarily to display the selected transmit filter width.
➥ While "M M - - 3 3 " is selected, push and hold [F-4 T T B B W W ]
for 1 sec. to select the transmit filter width from
narrow, middle and width.
• The transmit filter width window appears for showing
the selected transmit filter width each time [F-4 T T B B W W ]
is pushed.
Operation on the 5 MHz band is allowed on 5 discrete
frequencies and must adhere to the following:
• USB mode
• Maximum of 50 watts ERP
• 2.8 kHz bandwidth
It is the operator's responsibility to set all controls so
that the transmission in this band meets the stringent
conditions under which we may use these frequencies.
NOTE: We recommend that you store these fre-
quencies, mode and filter settings into the memory
channel for easy recall.
*The channel center frequencies that are specified
by the FCC, show the center frequency of their
passband. However, the IC-7000 displays carrier
point frequency, so set 1.5 kHz below from FCC
channel center frequency.
4
(Effective Radiated Power)
4
40