ABB SmartTouch i-bus KNX Product Manual page 10

10.24.36
10.24.37
10.24.38
10.24.39
10.24.40
10.24.41
10.24.42
10.24.43
10.24.44
10.24.45
10.24.46
10.24.47
10.24.48
10.24.49
10.24.50
10.24.51
10.24.52
10.24.53
10.24.54
10.24.55
10.24.56
10.24.57
10.24.58
10.24.59
10.24.60
10.24.61
10.24.62
10.24.63
10.24.64
10.24.65
10.24.66
10.24.67
10.24.68
10.24.69
10.24.70
10.24.71
10.24.72
10.24.73
10.24.74
10.24.75
10.24.76
10.24.77
10.24.78
10.24.79
10.24.80
10.24.81
10.24.82
10.24.83
10.24.84
10.24.85
10.24.86
10.24.87
Product manual 2CKA00xx73xxxxx
Temperature reading - Inputs of weighted temperature reading .............................................223
Temperature reading - Weighting of internal measurement (0 to 100%) .................................224
Temperature reading - Weighting of external measurement (0 to 100%) ................................224
Temperature reading - Weighting of external measurement 2 (0 to 100%) .............................224
Temperature reading - Cyclic sending of the actual temperature (min) ...................................224
Temperature reading - Difference of value for sending the actual temperature (x 0.1°C) ........225
Temperature reading - Adjustment value for internal temperature measurement (x 0.1°C) ....225
Temperature reading - Monitoring time for temperature reading (0 = no monitoring) (min) .....225
Temperature reading - Control value for fault (0 - 255) ...........................................................226
Alarm functions - Frost alarm temperature for HVAC and RHCC status (°C) ..........................227
Alarm functions - Heat alarm temperature for RHCC status (°C) ............................................227
Control of additional heating stage - Temperature difference to basic stage (x 0.1°C) ............227
Control of additional heating stage - Additional heating type ...................................................228
Control of additional heating stage - P-component (x 0.1°C) ..................................................228
Control of additional heating stage - I-component (min) ..........................................................229
Cooling control - Cooling type .................................................................................................229
Cooling control - P-component (x 0.1°C) .................................................................................230
Cooling control - I-component (min.) .......................................................................................230
Cooling control - Extended settings ...........................................................................................230
Basic stage cooling ...................................................................................................................231
Basic stage cooling - Status object cooling .............................................................................231
Basic stage cooling - Mode of the control value ......................................................................231
Basic stage cooling - Hysteresis (x 0.1°C) ..............................................................................232
Basic stage cooling - Cyclic sending of the control value (min) ...............................................232
Basic stage cooling - PWM cycle cooling (min) .........................................................................233
Basic stage cooling - Maximum control value (0 - 255) ...........................................................233
Basic stage cooling - Minimum control value for basic load (0 to 255) ....................................233
Settings of basic load - Minimum control value for basic load > 0 ...........................................234
Basic load settings - Basic load active when controller is off ...................................................234
Setpoint settings - Setpoint temperature for cooling comfort (°C) ...........................................235
Setpoint settings - Increase for standby cooling (°C) ..............................................................235
Setpoint settings - Increase for ECO cooling (°C) ...................................................................235
Setpoint settings - Set-point temperature for heat protection (°C) ...........................................236
Setpoint settings - Send current setpoint ................................................................................236
Setpoint settings - Cyclic sending of the current set-point temperature (min) ..........................236
Setpoint adjustment - Maximum manual increase during cooling mode (0 - 9°C) ...................236
Setpoint adjustment - Maximum manual reduction during cooling mode (0 - 9°C) ..................237
Setpoint adjustment - Resetting of the manual adjustment for receipt of a basic setpoint .......237
Setpoint adjustment - Resetting the manual adjustment for change of operating mode ..........237
Setpoint adjustment - Resetting the manual adjustment via object .........................................238
Setpoint adjustment - Permanent storage of on-site operation ...............................................238
Setpoint adjustment - Permanent storage of on-site operation ...............................................238
Temperature reading - Inputs of temperature reading .............................................................238
Temperature reading - Inputs of weighted temperature reading .............................................239
Temperature reading - Weighting of internal measurement (0 to 100%) .................................239
Temperature reading - Weighting of external measurement (0 to 100%) ................................239
Temperature reading - Weighting of external measurement 2 (0 to 100%) .............................240
Temperature reading - Cyclic sending of the actual temperature (min) ...................................240
Temperature reading - Difference of value for sending the actual temperature (x 0.1°C) ........240
Temperature reading - Adjustment value for internal temperature measurement (x 0.1°C) ....241
Temperature reading - Monitoring time for temperature reading (0 = no monitoring) (min) .....242
Temperature reading - Control value for fault (0 - 255) ...........................................................242
Table of contents
│10