Download Print this page

Siruba DT828L Manual page 18

Advertisement

縫紉
為了安全起见,在使用本縫紉機之前,請安裝
保護裝置。
如果未安裝這些安全裝置就使用縫紉機,會造
成人身傷害及縫紉機損壞,發生下列情況時,
請切斷電源,否則誤踩下啟動踏板時,縫紉機
動作會導致受傷。
●機針穿線時
●更換機針或梭芯時
●縫紉機不使用或人離開縫紉機時
縫紉過程中,不要觸摸任何運動部件或將物件
靠在運動部件上,因為會導致人員受傷或縫紉
機損壞。
縫紉機頭倒下時,請一定要固定工作台,不可
使其隨意移動,工作台移動易發生腳等被夾住
等事故。
縫紉機頭倒下或豎起時,請用雙手進行操作,
單手操作時因縫紉機自身的重量,萬一滑落易
導致受傷。
①縫紉
1. 一邊用手握住面線,一邊用手逆時針轉
動手輪,以將底線拉到送布齒上面。
2. 將底線朝自己身邊方向拉,底線應能平
穩地伸出。
3. 踏下啟動踏板開始縫紉。
②倒縫加固的方法
按下倒縫裝置按鈕開關 N(1)時,送料方
向將會方向,實現倒縫功能。釋放時,送
料方向恢復正常。
③密縫的方法
1. 在操作盒上設置好密封針距長度。
2. 按下密縫裝置按鈕開關 M(1)時,可以
用小的針距進行縫紉。釋放時,針距大小
恢復正常縫紉。
Lower
threads
Lower threads
P12
SEWING
Attach all safety devices before using the sewing ,achine.If the machine
ie used without these devices attached,injury may result.
Turn off the power switch at the following times, The machine may
operate if the treadle is depressed by mistake, which could result in injury.
● When threading the needle
● When replacing the bobbin and needle
● When not using the machine and when leaving the machine
unattended
Do not touch any of the moving parts or press any objects against the
machine while sewing, as this may result in personal injury or damage to
the machine.
Secure the table so that it will not move when tilting back the machine
head. If the table moves, it may crush your feet or cause other injuries.
Use both hands to hold the machine head when tilting it back or returning
it to its original.If only one hand is used, the weight of the machine head
may cause your hand to slip, and your hand may get caught.
① Sewing
1.While holding the two upper threads with your fingers, turn the
machine pulley by hand toward you until the lower threads come out
onto the feed dog.
2.Pull the lower threads toward you and check that they pull out
smoothly.
3.Step on the starter and start sewing.
② Backtacking
When the actuator switch N (1) is pressed during sewing, the feed
direction will be reversed. When it is released, the feed direction
will return to normal.
③ Sewing condensed stitches
1.In the operating box set close needle length.
2.Press the close seam device button,switch M (1),you can use
small.Sewing the needle spacting.When released, the distance
between the needles is restored Ordinary sewing.
Sewing
direction
Close needle

Advertisement

loading