[Initial Startup]; [Startup Input Select] - Panasonic PT-RQ13KU Operating Instructions (Functional Manual)

Note
f The power indicator <ON (G)/STANDBY (R)> will blink slowly in green while the no signal lights-out function is operating and the light source
is turned off.
f When [NO SIGNAL LIGHTS-OUT] is set to anything other than [DISABLE], the following are the conditions to turn the light source back on
again from the condition that the light source has turned off by this function.
g When the signal is input
g When on-screen display such as menu screen (OSD) or input guide, a test pattern, or a warning message is displayed
g When the power on <b> button is pressed
g When the operation to disable the shutter function (shutter: open) is performed, such as pressing the <SHUTTER> button
g When the operating environment temperature is around 0 °C (32 °F) and the light source is forced to turn on due to warm-up

[INITIAL STARTUP]

Set the startup method when the <MAIN POWER> switch is set to <ON>.
1) Press as to select [INITIAL STARTUP].
2) Press qw to switch the item.
f The items will switch each time you press the button.
[LAST MEMORY]
[STANDBY]
[ON]

[STARTUP INPUT SELECT]

Set the input when the projector is switched on to start projection.
1) Press as to select [STARTUP INPUT SELECT].
2) Press the <ENTER> button.
f The [STARTUP INPUT SELECT] screen is displayed.
3) Press asqw to select the input, and press the <ENTER> button.
[LAST USED]
[SDI1]
[SDI2]
[SDI3]
[SDI4]
[DIGITAL LINK]
[HDMI1 [SLOT1]]
[HDMI2 [SLOT1]]
[HDMI3 [SLOT2]]
[HDMI4 [SLOT2]]
[DVI-D1 [SLOT1]]
[DVI-D2 [SLOT1]]
[DVI-D3 [SLOT2]]
[DVI-D4 [SLOT2]]
[SDI1 [SLOT1]]
*1
[SDI2 [SLOT1]]
*1
[SDI3 [SLOT1]]
*3
[SDI4 [SLOT1]]
*3
[SDI1 [SLOT2]]
*3
[SDI2 [SLOT2]]
*3
[SDI3 [SLOT2]]
*2
[SDI4 [SLOT2]]
*2
[INPUT1] - [INPUT10]
*1 This can be set when the optional Interface Board equipped with corresponding input is installed in <SLOT 1>.
*2 This can be set when the optional Interface Board equipped with corresponding input is installed in <SLOT 2>.
*3 This is displayed when the optional Interface Board for 12G-SDI (Model No.: ET-MDN12G10) is installed in <SLOT 1> or <SLOT 2>.
*4 When the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) is connected to the projector, its input
name is automatically reflected from [INPUT1] to [INPUT10]. When an item that does not reflect the input name is selected, it will be disabled.
148 - ENGLISH
Chapter 4 Settings — [PROJECTOR SETUP] menu
Starts up the projector in the condition before the <MAIN POWER> switch is set to <OFF>.
Starts up the projector in standby.
Starts projecting immediately.
Keeps the input selected last.
Sets the input to SDI1.
Sets the input to SDI2.
Sets the input to SDI3.
Sets the input to SDI4.
Sets the input to DIGITAL LINK.
Sets the input to HDMI1 of the Interface Board.
*1
Sets the input to HDMI2 of the Interface Board.
*1
Sets the input to HDMI3 of the Interface Board.
*2
Sets the input to HDMI4 of the Interface Board.
*2
Sets the input to DVI-D1 of the Interface Board.
*1
Sets the input to DVI-D2 of the Interface Board.
*1
Sets the input to DVI-D3 of the Interface Board.
*2
Sets the input to DVI-D4 of the Interface Board.
*2
Sets the input to SDI1 of the Interface Board.
Sets the input to SDI2 of the Interface Board.
Sets the input to SDI3 of the Interface Board.
Sets the input to SDI4 of the Interface Board.
Sets the input to SDI1 of the Interface Board.
Sets the input to SDI2 of the Interface Board.
Sets the input to SDI3 of the Interface Board.
Sets the input to SDI4 of the Interface Board.
Sets the input to DIGITAL LINK, and switches the input of the Panasonic twisted-pair-cable
*4
transmitter to the specified input.