1 General Information 1.1 Revision History Rev. Date Description 2018-10-24 Released version 2020-05-12 Changed to Avnet CI 1.2 Reference Documents COM Express Module Base Specification COM Express Revision 2.1 Last update: April 10 , 2012 PCI Local Bus Specification Rev. 2.1 PCI21.PDF...
MSC C10-MB-EV User Manual 1.3 Introduction COM Express™ is an open specification from PICMG (PCI Industrial Computer Manufacturer Group). It is a module concept to bring PCI Express and other newer technologies like SATA, USB 3.0 and different display interfaces onto a COM (Computer On Module).
MSC C10-MB-EV User Manual Technical Description 2.1 Key features The MSC C10-MB-EV is designed as a type 10 carrier according to COM Express® Module Base Specification Revision 2.1. Key features include: Interface for COM Express module type 10 ...
MSC C10-MB-EV User Manual 3 Mechanics 3.1 Dimensions Dimension: 170 mm x 170 mm Width: 1.6 mm + /-10% Tolerances of the drill holes: +/- 0.1mm in X and Y Tolerances of the diameter: + 0.1 mm 3.2 Assembly notes...
MSC C10-MB-EV User Manual 4 Hardware 4.1 Plug-in Position of the COM Express module Socket for a COM Express type 10 module is available on the base board. Specification: Reference: X301 Connector: AMP / Tyco 3-1827233-6 0.5 mm pitch free height 220 pin 5H plug ...
MSC C10-MB-EV User Manual 4.2 PCI Express Lanes Four PCIe lanes are defined at the Type10 COM Express module. Three PCIe lanes are fixed routed to the PCIe x16 connector. The PCIe Lane 3 can be routed to the PCIe x16 connector or to the PCI Express Mini Card slot card slot.
Page 16
MSC C10-MB-EV User Manual Signal Signal PRSNT1# (GND) JTAG_TCK not connected SMB_CLK JTAG_TDI not connected SMB_DAT JTAG_TDO not connected JTAG_TMS not connected JTAG_RST# not connected 3V3_AUX PE_RST# WAKE# RSVD REFCLK+ REFCLK- PET_p0 PET_n0 PER_p0 PER_n0 PRSNT2# RSVD PET_p1 PET_n1 PER_p1...
Page 17
MSC C10-MB-EV User Manual PET_p7 PET_n7 PER_p7 not connected PER_n7 not connected PRSNT2# RSVD PET_p8 not connected PET_n8 not connected PER_p8 not connected PER_n8 not connected PET_p9 not connected PET_n9 not connected PER_p9 not connected PER_n9 not connected PET_p10 not connected...
MSC C10-MB-EV User Manual 4.4 PCI Express Mini Card PCIe Lane 3 and the signals from USB port 6 switch to this slot if J2001 is set. If the Mini Card slot is selected, PCIe Lane 3 at X2701 and USB port 6 at X1902 are no longer useable.
MSC C10-MB-EV User Manual Display Port (DP) Specification: References: X801 Connector: Molex 1050200001 Pin-out: Refer to Table 3 Signal name Function LANE 0 + LANE 0 positive data signal Ground LANE 0 - LANE 0 negative data signal...
MSC C10-MB-EV User Manual Ground LANE 3 - LANE 3 negative data signal CONFIG1 CA_DET (cable detect) CONFIG2 Ground AUX CH + Auxiliary Channel positive signal Ground AUX CH - Auxiliary Channel negative signal HPDET Hot Plug Detect Return Ground...
Page 21
MSC C10-MB-EV User Manual Specification: References: X1602 Connector: Tyco 5-2069716-3, I-PEX 20455-040E-02 Pin-out: Refer to Table 4 Signal name Function Reserved for LCD manufacturer’s use RSVD BL_PWR Backlight power BL_PWR Backlight power BL_PWR Backlight power BL_PWR Backlight power...
Page 22
MSC C10-MB-EV User Manual Table 4 Pin-out embedded Display Port The supply voltage of the eDP logic and the eDP backlight can be adjusted with jumper JP1101 and JP1102. The according position is printed on the PCB. Refer to chapter 4.7 LVDS-Interface.
MSC C10-MB-EV User Manual LVDS Interface Any LVDS display can be connected via a JILI30 connector. One 24 bit LVDS channel is present on this 30-pin connector. The signals of the LVDS interface are shared with the eDP port. To use the signals for the LVDS S2802 #3 has to be set open.
Page 24
MSC C10-MB-EV User Manual Specification: References: X1601 Connector: JAE FI-X30SSL-HF Pin-out: Refer to Table 5 "JILI30" according to JILI specification [4] Signal name Function LVDS_A0- LVDS Negative data signal (-) LVDS_A0+ LVDS Positive data signal (+) LVDS_A1-...
MSC C10-MB-EV User Manual 4.7.1 LVDS EEPROM Socket A serial EEPROM is connected to the signals LVDS_I2C_CK and LVDS_I2C_DAT to store configuration data of the LCD. This EEPROM can be assembled optionally or it can be disabled with a closed DIP-Switch S2804 #4 to avoid conflicts with configuration EEPROM connected via the JILI connector.
MSC C10-MB-EV User Manual 4.7.2 Backlight Inverter Interface The supply voltage of the backlight can be adjusted with jumper JP1102. The according position is printed on the PCB. DIP switch S2804 #3 should be set according to the backlight inverter used.
MSC C10-MB-EV User Manual 4.8 Audio A Realtek ALC888 or ALC886 HD audio codec is connected to the AC link of the COM Express module. Following LF signals are provided by the HDA codec: Stereo LineIn Stereo LineOut ...
MSC C10-MB-EV User Manual SATA-Interface Two SATA drives can be connected to the SATA interfaces. Note: Depending on the COM Express module used, not all SATA ports are available. SATA Channel References SATA 0 X2101 SATA 1 X2102 Table 10 Assignment SATA Channel to Connector Reference Specification: ...
MSC C10-MB-EV User Manual 4.10 USB Topology Eight USB ports are provided by the C10-MB-EV carrier. The exact assignment of each port is defined in the following table: USB-Port References Function Location Power jumper Remarks USB0 X702 USB 3.0 I/O Shield...
MSC C10-MB-EV User Manual 4.10.1 USB Power Supply The power supplies are protected by USB power switches. With power jumper setting the USB power can be sourced from standard +5V (2-3) or from suspend +5V (1-2). The USB power switches have the following functions: ...
MSC C10-MB-EV User Manual 4.10.3 USB Client Connector The USB Port 7 signals were switched to a 5 pin header, if a USB client is plugged at X1903. Specification: References: X1903 Connector: single row pin header Pin-out: Refer to Table 14 ...
MSC C10-MB-EV User Manual 4.12 LPC Connector The LPC signals are available on a pin header. Specification: References: X1403 Connector: 10 pin header, 2.54mm Pin-out: Refer to Table 16 Signal Signal LPC_CLK LPC_LAD0 LPC_FRAME# LPC_LAD1 LPC_RST# LPC_LAD2...
MSC C10-MB-EV User Manual 4.13 GPIO The COM Express module provides four general purpose outputs and four general purpose inputs. They are shared with the SD Memory Card signals. The GPIs have pull-up resistors and are routed to a DIP switch (S2805). With the DIP switch the GPIs can be connected to ground.
MSC C10-MB-EV User Manual 4.13.1 GPIO Connector Don’t set jumper J3001 to use the GPI signals at X3001. (Default) Specification: References: X3001 Connector: 10 pin header, 2.54mm Pin-out: Refer to Table 17 Signal Signal VCC3V3 GPO0 GPI0...
MSC C10-MB-EV User Manual 4.14 Super IO The Winbond Super IO W83627HG is integrated on the base board. Interfaces used by the Super IO: 2 RS232 interface (function of COM port shared with IrDA interface) 1 LPT interface ...
MSC C10-MB-EV User Manual 4.14.4 PS/2 Connector The PS/2 signals are routed to a 7pin single row header to connect PS/2 keyboards and PS/2 mice. Specification: References: X2305 Connector: 7 pin single row header 2.54mm Pin-out: Refer to Table 21...
MSC C10-MB-EV User Manual 5) Note: The power at 12V PCIe, VCC_LCD (X1601), VCC_BL_EDP (X1602), VCC_BL (X1101) and 12V fan power are switched off, when the power input is not in the range of 11V to 13V. In that case, you can feed 12V from an external power source at X1603 pin 4 to supply these connectors with power.
MSC C10-MB-EV User Manual 4.17 External SPI BIOS-Flash There is a socket (SO8 220) on the motherboard, where an additional BIOS-Flash can be inserted. The BIOS SPI flash can be selected with DIP switch S2802. BIOS_DIS1 BIOS_DIS0 BIPOS Entry (SPI_CS#)
MSC C10-MB-EV User Manual 4.19 Power Supply ATX Connector An ATX connector with additional ATX12V connector is available to power the system. Specification ATX connector: References: X1503 Connector: Molex 39-29-9202 Pin-out: Refer to ATX specification V2.2 [2] Specification 2 pol.
Page 44
MSC C10-MB-EV User Manual Illustration 3 Miscellaneous Parts 44 / 48...
MSC C10-MB-EV User Manual 4.20 Auxiliary Power Connector An auxiliary power connector is available to power some interfaces when the input power is not in the 11V to 13V range and the power at 12V PCIe, VCC_LCD (X1601), VCC_BL_EDP (X1602), VCC_BL (X1101) and 12V fan power are switched-off. In that case, you can feed 12V from an external power source at X1603 pin 4 to supply these connectors with power.
MSC C10-MB-EV User Manual 4.22 Power Button For switching the system on a power push button has been implemented. The PWR_BTN# signal is low-active and is connected directly to the corresponding pin of the COM Express module. References: SW2901 ...
MSC C10-MB-EV User Manual 4.25 WLAN LEDs There are three yellow LEDs placed near PCIe Mini Card slot. They indicate the card type. Wireless Wide Area Network (WWAN). Wireless Local Area Network (WLAN). Wireless Personal Area Network (WPAN).