Related Manuals for Avnet Qseven MSC Q7-MB-EP6
Summary of Contents for Avnet Qseven MSC Q7-MB-EP6
- Page 1 User Manual Qseven Baseboard MSC Q7-MB-EP6 REV 1.1 2020-05-07 www.msc-technologies.eu...
-
Page 2: Preface
MSC Q7-MB-EP6 User Manual Preface Copyright Notice Copyright © 2015 MSC Technologies GmbH. All rights reserved. Copying of this document, and giving it to others and the use or communication of the contents thereof, is forbidden without express authority. Offenders are liable to the payment of damages. - Page 3 MSC Q7-MB-EP6 User Manual Product Support MSC engineers and technicians are committed to provide support to our customers whenever needed. Before contacting the Technical Support, please consult the respective pages on our web site at www.msc-technologies.eu for the latest documentation, drivers and software downloads.
-
Page 4: Table Of Contents
MSC Q7-MB-EP6 User Manual Contents PREFACE ..........................2 CONTENTS ..........................4 FIGURES ............................ 6 TABLES ............................. 7 GENERAL INFORMATION ....................8 Revision History ........................8 Reference Documents ......................8 Definitions and Abbreviations ..................... 9 INTRODUCTION ......................10 QsevenTM Product Description ..................10 Features .......................... - Page 5 MSC Q7-MB-EP6 User Manual Wireless Operation on mini PCIe Add-in Cards (J501) ........28 PCIe Mini Card Status LEDs ..................28 3.10 RS-232 ..........................28 UART0, DB9 Connector (X705) ................28 UART2, RS232 Connector (X702) ................29 3.11 RS485 (X703) ........................29 3.12 Serial Communication Selection (J703) ................
-
Page 6: Figures
MSC Q7-MB-EP6 User Manual Figures Block diagram Q7-MB-EP6 baseboard ............... 12 Figure 1 Positioning of connectors and jumpers (Q7-MB-EP6 baseboard top view) ..13 Figure 2 Figure 3 Positioning of connectors (Q7-MB-EP6 baseboard bottom view) ......14 Dimensions of Q7-MB-EP6 Baseboard ............... 15 Figure 4 Jumper row X80x (X803, X804 and X805) .............. -
Page 7: Tables
MSC Q7-MB-EP6 User Manual Tables Revision history ......................... 8 Table 1 Pinout QsevenTM connector (X202) ................18 Table 2 Table 3 Pinout DisplayPort connector X301 ................19 Pinout JILI30 connector X801 ..................20 Table 4 Pinout backlight connector X802 .................. 21 Table 5 Table 6 Jumper settings LCD panel power X80x .............. -
Page 8: General Information
2016-01-17 Rework with changes and corrections 2016-01-25 Minor fixes 2016-09-16 Minor fixes 2017-07-25 Minor fixes 2020-05-07 Changed to Avnet CI Table 1 Revision history 1.2 Reference Documents Qseven Module Specification Revision 2.0 http://www.sget.org/standards/qseven.html PCI Local Bus Specification Rev. 2.1 PCI21.PDF Last update: June 1st, 1995 http://www.pcisig.com... -
Page 9: Definitions And Abbreviations
MSC Q7-MB-EP6 User Manual Universal Bus Specification usb_20.pdf Last update: April 27th, 2000 SuperSpeed USB (USB3.0), Oct 2012. http://www.usb.org SDIO Card Specification [10] Simplified_SDIO_Card_Spec.pdf Last update: February 8th, 2007 http://www.sdcard.org PCIe Mini Card Specification [11] http://www.pcisig.com 1.3 Definitions and Abbreviations Computer-On-Module Real Time Clock Peripheral Component Interconnect... -
Page 10: Introduction
MSC Q7-MB-EP6 User Manual 2 Introduction 2.1 QsevenTM Product Description Qseven modules are off the shelf compact, highly integrated computer on module devices designed to be plugged into a carrier baseboard. The Qseven standard is supported by multiple companies and defines a standardized square board of 70x70 mm size with a defined interface to the carrier board. -
Page 11: Features
MSC Q7-MB-EP6 User Manual 2.2 Features Display Port connector display interface LVDS LCD panel interface, using the standard JILI30 connector 5 Pin LCD panel backlight connector 12V Backlight support via on board 12V regulator HDA Audio Codec Realtec ALC888 and audio signal connector ... -
Page 12: Block Diagram
MSC Q7-MB-EP6 User Manual 2.3 Block diagram RS232 Transceiver 2 Pin RS485 Analog MicroAB UART0 USB1 Header Transceiver Multiplexer Host/Client 10 Pin RS232 USB 2.0 UART_MFG USB3 Header Transceiver Type A (UART2) 6 Pin USB 2.0 SMBus/I2C USB5 Test Point Type A 10 Pin Header... -
Page 13: Positioning Of Connectors And Jumpers
MSC Q7-MB-EP6 User Manual 2.4 Positioning of connectors and jumpers X604 X507 X506 X703 X902 X1102 J1001 J601 X705 X702 X1001 X905 X1005 X401 LED1003 X601 LED505 X901 LED1002 LED504 X704 X503 J1305 X301 X801 J1302 J501 X603 X602 J1102 X502 X504 X904... -
Page 14: Figure 3 Positioning Of Connectors (Q7-Mb-Ep6 Baseboard Bottom View)
MSC Q7-MB-EP6 User Manual X202 X907 X802 X1004 Battery Gold Cap Figure 3 Positioning of connectors (Q7-MB-EP6 baseboard bottom view) 14 / 35... -
Page 15: Dimensions
MSC Q7-MB-EP6 User Manual 2.5 Dimensions Dimension: 148.02 mm x 102.22 mm Board Thickness: 1.8 mm + /-10% Drill hole positioning tolerance: +/- 0.1mm in X and Y Drill hole diameter tolerance: + 0.1 mm Max height of component on Top side: 19.3mm Max height of component on Bottom side: 5.4mm... -
Page 16: Hardware
MSC Q7-MB-EP6 User Manual 3 Hardware NOTE: Not all QsevenTM modules may support all connectors and functionality available on the MSC Q7-MB-EP6 embedded platform baseboard. 3.1 QsevenTM connector specification (X202) Reference: X202 Type: ACES. 88882-2D0M Mating: PCB Q7 Module Row A Pin # Row B GBE_MDI3-... - Page 17 MSC Q7-MB-EP6 User Manual Row A Pin # Row B THRMTRIP# WDOUT USB_P7- / USB_SSTX0- USB_P6- / USB_SSRX0- USB_P7+/ USB_SSTX0+ USB_P6+ / USB_SSRX0+ USB_4_5_OC# USB_6_7_OC# USB_P5- / USB_SSTX1- USB_P4- / USB_SSRX1- USB_P5+ / USB_SSTX1+ USB_P4+ / USB_SSRX1+ USB_2_3_OC# USB_0_1_OC# USB_P3- USB_P2- USB_P3+ USB_P2+...
-
Page 18: Video Interface Via Displayport Connector Specification (X301)
MSC Q7-MB-EP6 User Manual Row A Pin # Row B UART0_TX UART0_RTS# PCIE1_RX+ PCIE1_TX+ PCIE1_TX- PCIE1_RX- UART0_RX UART0_CTS# PCIE0_RX+ PCIE0_TX+ PCIE0_TX- PCIE0_RX- LPC_AD0 / GPIO0 LPC_AD1 / GPIO1 LPC_AD2 / GPIO2 LPC_AD3 / GPIO3 LPC_CLK / GPIO4 LPC_FRAME# / GPIO5 SERIRQ / GPIO6 LPC_LDRQ# / GPIO7 VCC_RTC... -
Page 19: Lcd Panel Lvds Interface
MSC Q7-MB-EP6 User Manual Signal name Signal name ML_Lane 1N ML_Lane 2P ML_Lane 2N ML_Lane 3P ML_Lane 3N AUXCH P AUXCH N Hot Plug Detect Return for Power +3.3V Power (max 0.5A) Table 3 Pinout DisplayPort connector X301 3.3 LCD Panel LVDS Interface JILI30 Connector (X801) LCD/TFT displays with LVDS inputs can be connected via the JILI30 connector X801. -
Page 20: Backlight Inverter Interface (X802)
MSC Q7-MB-EP6 User Manual Signal name Function LVDS_A3+ LVDS Positive data signal (+) eDP0_TX3+ Display Port primary channel data signal pair 3 (+) LVDS_B0- LVDS Negative data signal (-) eDP1_TX0- Display Port secondary channel data signal pair 0(-) LVDS_B0+ LVDS Positive data signal (+) eDP1_TX0+ Display Port secondary channel data signal pair 0(+) Ground... -
Page 21: Lvds Eeprom
MSC Q7-MB-EP6 User Manual The analog signal level is derived either from the inverted or from the non-inverted PWM signal. (The PWM signal is integrated and then limited to the selected peak voltage of the backlight inverter). The peak level of the brightness signal can be selected with a jumper on X803 to be either 3.3V or 5V. -
Page 22: Backlight Power Selection Jumper
MSC Q7-MB-EP6 User Manual X80x Pins Function, LCD panel power supply voltage Power always on Panel is no longer enabled by LVDS_VDD_EN# signal, but is permanently enabled if this jumper is installed. (default) +3.3 V +5.0 V +12V Table 6 Jumper settings LCD panel power X80x 3.3.4.2 Backlight power selection jumper The backlight power for the inverter or LED driver is selected using jumpers on X80x. -
Page 23: Backlight Brightness Control Jumpers
MSC Q7-MB-EP6 User Manual 3.3.4.5 Backlight brightness control jumpers The jumpers on X80x are used in combination to select the type of brightness control signal used for the LCD panel backlight inverter or LED driver. The signal coming from the QsevenTM module is typically a PWM signal. -
Page 24: Sata Interface Specification (X506, X507)
MSC Q7-MB-EP6 User Manual 3.4 SATA interface specification (X506, X507) A SATA drive can be connected to SATA channel 0 via the connector X506. An onboard LED (LED504) is provided to indicate activity on the SATA port. The SATA can be powered by connector X507. -
Page 25: Ethernet Connector Specification (X504, X505)
MSC Q7-MB-EP6 User Manual Row A Row B VCC3V3 VCC1V5 SATA1_RX+ VCC3V3 SATA1_RX- VCC1V5 SMB_CLK SATA1_TX- SMB_DAT SATA1_TX+ VCC3V3 VCC3V3 VCC1V5 mSATA_ACT VCC3V3 Table 15 Pinout mSATA connector X503 3.6 Ethernet connector specification (X504, X505) The MSC Q7-MB-EP6 Board offers two Gigabit Ethernet ports. They can be connected to a local area network via a 10/100/1000 Base-T interface. -
Page 26: Usb Topology
MSC Q7-MB-EP6 User Manual 3.7 USB Topology Eight USB ports are normally provided by the Qseven module. The assignment of the ports is defined in Table 16: Signal Source Target Remark USB[1]+ Qseven connector X604 USB Client / Host USB[1]- USB1 USB[2]+ Qseven... -
Page 27: On Board 5 Pin Usb Connector (X601)
MSC Q7-MB-EP6 User Manual On Board 5 Pin USB Connector (X601) References: X601 Type: Weitronic 353-17-21-05-60-1-2-00 Mating: female crimp-connector Reference FCI 65039-032 Signal Signal USB_VCC0 USB_R0- No Connect USB_R0+ Table 18 Pinout Internal USB Connector X601 USB 3.0 Connector (X704) References: X704 Type:... -
Page 28: Pcie Mini Card (X502)
MSC Q7-MB-EP6 User Manual 3.9 PCIe Mini Card (X502) Both Full-mini and Half-mini size cards can be plugged into the mini PCIe connector X502. Additional holes are provided to accommodate the Half-mini size cards. References: X502 Type: Molex 67910-9000 Mating: mini PCIe size card with PCIe or USB interface Pinout: Refer to Mini PCIe Mini Card Specification [11]... -
Page 29: Uart2, Rs232 Connector (X702)
MSC Q7-MB-EP6 User Manual Signal name Function DCD# Not available Receive data Transmit data DTR# Not available Ground DSR# Not available RTS# Request to send CTS# Clear to send Not available Table 21 Pinout X701 UART2, RS232 Connector (X702) A second RS232 port with no hand shake signals is provided on the connector X702. References: X702 (COM) Type:... -
Page 30: Serial Communication Selection (J703)
MSC Q7-MB-EP6 User Manual 3.12 Serial Communication Selection (J703) The jumper J703 selects whether the UART0 signals are routed to the DB9 X705 connector to establish a RS232 connection or to the connector X703 to establish a RS485 connection. J703 Function removed (default) RS232 on DB9 X705... -
Page 31: Spi Interface, Bios Disable/Alternative Boot (X1001, J1001)
MSC Q7-MB-EP6 User Manual 3.15 SPI Interface, Bios disable/Alternative Boot (X1001, J1001) References: X1001 Type: Weitronic 137-10-3-60-1-2-10 Mating: female crimp-connector Reference FCI 65043-032 Pin Signal (Rev1)* Pin Signal (Rev1)* SPI_CS0# (MISO) +3V3 (BIOS_DIS#) SPI_MISO (MOSI) HOLD# (10k pull-up (CS0#) 3V3) (10k pull-up 3V3) (SCK) SPI_SCK... -
Page 32: Smbus, I2C Interface (X902)
MSC Q7-MB-EP6 User Manual 3.17 SMBUS, I2C Interface (X902) The EP6 baseboard provides test points for the SMBus and the I2C-bus. A 6 pin connector can also be assembled, if needed. X902 is by default not populated. References: X902 Type: CAB 1001-161-006-RoHS Mating: female crimp-connector Reference FCI 65039-031... -
Page 33: Sdio Card Socket (X1004)
MSC Q7-MB-EP6 User Manual 3.21 SDIO Card Socket (X1004) A SD card socket is provided on the EP6 board to read from the SD card. References: X1004 Type: SD DM1AA-SF-PEJ(21) Hirose Mating: SD Memory Card Pinout: See SDIO Card specification [10] SDIO Card LEDs There are two SD card LEDs on board. -
Page 34: Power Button
MSC Q7-MB-EP6 User Manual Power Button To control the system with a power button a switch may be connected to the pins 5-6 of X904 connector. The PWR_BTN# signal is low-active and is connected directly to the corresponding pin of the Qseven module. -
Page 35: Vendor Specific Signals Mfg_Nc3 And Mfg_Nc4 (J701, J702)
MSC Q7-MB-EP6 User Manual 3.23 Vendor Specific Signals MFG_NC3 and MFG_NC4 (J701, J702) The EP6 carrier board provides these 2 signals on jumpers for boot loader implementation and firmware development. J702 pins Fan Power 1-2 (default) MFG_NC3 high, 10k pull-up to +3,3V MFG_NC3 low, GND Table 36 Jumper J702...