Discrete Input Data Points - Uponor Smatrix Base PRO X-148 Installation Manual

Display name
Room setpoint override,
cannel 4
Room setpoint override,
cannel 5
Room setpoint override,
cannel 6
Room setpoint override,
cannel 7
Room setpoint override,
cannel 8
Room setpoint override,
cannel 9
Room setpoint override,
cannel 10
Room setpoint override,
cannel 11
Room setpoint override,
cannel 12
* Requires Heat Pump Integration via BMS to be activated in U_BMS.txt. It
takes about 2 minutes for the actuators in the Base PRO system to be fully
opened.

3.4 Discrete Input data points

These datapoints are read only and show the actuator, pump/boiler,
and GPI status on the controller (binary, on/off).
Display name
Actuator status/channel 1
(bit 0)
Actuator status/channel 2
(bit 1)
Actuator status/channel 3
(bit 2)
Actuator status/channel 4
(bit 3)
Actuator status/channel 5
(bit 4)
Actuator status/channel 6
(bit 5)
Actuator status/channel 7
(bit 6)
Register Physical
address address
(decimal) (decimal)
00033 00032
00034 00033
00035 00034
00036 00035
00037 00036
00038 00037
00039 00038
00040 00039
00041 00040
Register Physical
address address
(decimal) (decimal)
10001 10000
10002 10001
10003 10002
10004 10003
10005 10004
10006 10005
10007 10006
Uponor Smatrix Base PRO Controller X-148 Modbus RTU
Function Type
code (Hex)
0x01 Read
0x05 Write
0x0F Write
multiple
0x01 Read
0x05 Write
0x0F Write
multiple
0x01 Read
0x05 Write
0x0F Write
multiple
0x01 Read
0x05 Write
0x0F Write
multiple
0x01 Read
0x05 Write
0x0F Write
multiple
0x01 Read
0x05 Write
0x0F Write
multiple
0x01 Read
0x05 Write
0x0F Write
multiple
0x01 Read
0x05 Write
0x0F Write
multiple
0x01 Read
0x05 Write
0x0F Write
multiple
Function Type
code (Hex)
0x02 Read
0x02 Read
0x02 Read
0x02 Read
0x02 Read
0x02 Read
0x02 Read
Analogue/ Coding
Binary
Binary Unsigned.
0 = Setpoint override disabled (default)
1 = Setpoint override enabled
Binary Unsigned.
0 = Setpoint override disabled (default)
1 = Setpoint override enabled
Binary Unsigned.
0 = Setpoint override disabled (default)
1 = Setpoint override enabled
Binary Unsigned.
0 = Setpoint override disabled (default)
1 = Setpoint override enabled
Binary Unsigned.
0 = Setpoint override disabled (default)
1 = Setpoint override enabled
Binary Unsigned.
0 = Setpoint override disabled (default)
1 = Setpoint override enabled
Binary Unsigned.
0 = Setpoint override disabled (default)
1 = Setpoint override enabled
Binary Unsigned.
0 = Setpoint override disabled (default)
1 = Setpoint override enabled
Binary Unsigned.
0 = Setpoint override disabled (default)
1 = Setpoint override enabled
Analogue/ Coding
Binary
Binary Unsigned.1 = ON, 0 = Off.
Binary Unsigned.1 = ON, 0 = Off.
Binary Unsigned.1 = ON, 0 = Off.
Binary Unsigned.1 = ON, 0 = Off.
Binary Unsigned.1 = ON, 0 = Off.
Binary Unsigned.1 = ON, 0 = Off.
Binary Unsigned.1 = ON, 0 = Off.
| Installation manual | 19