Related Manuals for AGA Professional AMPRO36DF-SS
Summary of Contents for AGA Professional AMPRO36DF-SS
- Page 1 Professional 90 Dual Fuel User Guide & Installation & Service Instructions U110246 - 05...
-
Page 2: Table Of Contents
Contents Before You Start... Installation In Case of Fire Regulations To Prevent Fire or Smoke Damage Installation Safety Instructions Wear Suitable Clothing Converting to Propane Gas Use Only Dry Potholders or Oven Gloves Location of the Range Important Safety Notice and Warning Positioning the Range Proper Installation Fitting the Oven Handle... -
Page 3: Before You Start
1. Before You Start... Read all instructions before using this appliance. Save Many plastics will burn and most are damaged by heat. Keep these instructions for future reference. plastic items away from parts of the range that may become warm or hot. Do not leave plastic items on the cooktop as Have your appliance properly installed and grounded by they may burn, melt or soften if left too close to a vent or a a qualified technician in accordance with the National... -
Page 4: Wear Suitable Clothing
To avoid risk of electrical shock, personal injury, or death, Users of this appliance are hereby warned that the burning make sure your range has been properly grounded and of gas can result in low-level exposure to some of the listed always disconnect it from the main power supply before substances, including benzene, formaldehyde and soot, due servicing. -
Page 5: Use The Right Size Pan
If the flame is distorted, check that the burner head is DO NOT clean the door gasket: the door gasket is essential for a good seal. Care should be taken not to correctly placed over the burner. rub, damage or move the gasket. MAKE SURE THE FLOW OF COMBUSTION AND VENTILATION AIR TO THE RANGE IS UNOBSTRUCTED. - Page 6 the location of the range circuit breaker. Mark it for easy When an oven is on, do not use the top of the flue (the holes reference. Always allow the range to cool and then switch along the back of the range) for warming plates, dishes, off at the circuit breaker before cleaning or carrying out any drying dish towels or softening butter.
-
Page 7: Range Overview
Range Overview DocNo.025-0101 - Overview - 90 DF SC - Prof+ FX Fig. 2.1 PROFESSIONAL ArtNo.270-0029 - Prof+ 90SC annotated The dual fuel single cavity range (Fig. 2.1) has the following Fig. 2.2 features: 5 hotplate burners A control panel incorporating a timer A multi-function oven A storage drawer Cooktop Burners... -
Page 8: Igniting Cooktop Burners Without Electricity
The igniter should spark and light the gas. Keep holding the Fig. 2.3 knob pressed in to let the gas through to the burner for about ten seconds. If, when you let go of the control knob, the burner goes out, then the FSD has not been bypassed. -
Page 9: Wok Cradle (Optional Extra)
DO NOT put it crossways – it will not fit properly and Fig. 2.10 will be unstable (Fig. 2.9). DO NOT put it on any other burners – it is not designed to fit in any of the other grates. Position the griddle over the hotplate burners resting on the grates (Fig. -
Page 10: Operating The Oven
Please remember that all ranges vary – temperatures in your ArtNo.272-0017 new ovens may differ to those in your previous range. 90 Aga Professional - MF oven controls Fig. 2.13 Operating the Oven The multi-function oven has two controls: a function selector and a temperature setting knob (Fig. - Page 11 Convection Oven Fig. 2.16 This function operates the fans and the heating element around them (Fig. 2.18). An even heat is produced throughout the oven, allowing you to cook large amounts quickly. Convection oven cooking is particularly suitable for multi- rack cooking and is a good ‘all-round’...
- Page 12 Conventional Oven (Top and Base Heat) Fig. 2.21 This function combines the heat from the top and base elements (Fig. 2.21). It is particularly suitable for roasting and baking pastry, cakes and biscuits. Food cooked on the top rack will brown and crisp faster than on the lower rack, because the heat is greater at the top of the oven than at the base, as in ‘fan assisted oven’...
-
Page 13: Accessories
Accessories Fig. 2.25 Fig. 2.24 ArtNo.326-0014 - Cradle rack (Falcon) Oven Racks Each range is supplied with the following: • 1 broiler pan rack with telescopic runners (Fig. 2.24) • 2 flat racks with telescopic runners (Fig. 2.25) • 2 broiler pans with grids (Fig. 2.26) Fig. - Page 14 To Remove and Refit the Ladder Rack Supports Fig. 2.32 Lift the ladder support hooks out of the two locating holes in the oven side (or divider) before lifting the support clear of the bottom ladder restraint. ArtNo.320-0017 Main oven light Refit by inserting the bottom of the ladder into the restraint before fitting the hooks through the locating holes.
-
Page 15: The Clock
The Clock The clock must be set to the time of day before the oven Fig. 3.1 ArtNo.300-0005 2BC will work. minute minder setting Setting the Clock Once the cooker is connected and switched on, the display will start to flash. To set the time, turn the Timer (A) knob to the Clock (C) setting and back to the Manual (D) position. - Page 16 To Stop the Oven at a Specific Time of Fig. 3.5 You have set the required temperature and function mode and you would like the oven to automatically stop. TOP TIP Make a note of the current time so you do not forget. Fig.
- Page 17 To Start and Stop the Oven Fig. 3.9 Automatically The timer allows you to automatically start and stop by a combination of the length of the cooking time and the stop time. Giving you the flexibility to cook casseroles etc while you are out.
-
Page 18: Cooking Tips
Cooking Tips Cooking with a Multi-function Oven General Oven Tips Remember: not all modes are suitable for all food types. The The wire racks should always be pushed firmly to the back of oven cooking times given are intended for a guide only. the oven. -
Page 19: Cooking Table
Cooking Table The oven control settings and cooking times given in the table below are intended to be used as a guide only. Individual tastes may require the temperature to be altered to provide a preferred result. ArtNo.050-0019 - Albertine SC Food is cooked at lower temperature in a convection oven than in a conventional oven. -
Page 20: Troubleshooting
Troubleshooting Cooktop ignition or cooktop burners faulty If there is an installation problem and I don’t get my original installer to come back to fix it who pays? Is the power on? You do. Service organizations will charge for their service if Are the sparker (ignition electrode) or burner holes blocked they are correcting work carried out by your original installer. - Page 21 Has the oven knob been left in the OFF position by mistake? Fig. 6.1 Is the oven locked (see above)? Oven temperature getting hotter as the range gets older If turning the knob down has not worked or only worked for a ArtNo.324-0005 Oven light bulb short time then you may need a new thermostat.
-
Page 22: Cleaning Your Range
Cleaning Your Range Essential Information Fig. 7.1 Before thorough cleaning, turn off the circuit breaker. Allow the range to cool. After cleaning, remember to switch on the circuit breaker and ArtNo.311-0028 - Burner head off reset the clock before re-using the range. Never use paint solvents, caustic cleaners, biological powders, bleach, chlorine based bleach cleaners, coarse abrasives or salt. -
Page 23: Griddle (Optional Extra)
Avoid using any abrasive cleaners including cream Fig. 7.4 cleaners on brushed stainless steel surfaces. Never use caustic or abrasive cleaners as these will damage the surface. Griddle (Optional Extra) Always clean the griddle after use. Allow to cool completely ArtNo.272-0015 - 90DF - Pro+ - Removing the outer door panel before removing. - Page 24 Tilt the front of the rack downwards and then lift clear of the Fig. 7.7 runners (Fig. 7.6). Refit in the reverse order, making sure to push the rack down onto the runner arms. To Remove and Refit the Ladder Rack Supports Lift the ladder support hooks out of the two locating holes in the oven side (or divider) before lifting the support clear of the bottom ladder restraint.
-
Page 25: Cleaning Table (Table 7.2)
Chrome supports scouring pad. Cleaning Table Hot soapy water and soft cloth. (Table 7.2) ArtNo.050-0070 - Cleaning table AGA Professional Mildly abrasive cleaner with a soft Door inner Glass Cleaners listed are available from supermarkets or electrical cloth. retailers as stated. For enamelled surfaces use a cleaner that is... - Page 26 WARNING! If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. WHAT TO DO IF YOU SMELL GAS Do not try to light any appliance.
-
Page 27: Installation
INSTALLATION Check the appliance is electrically safe and gas sound when you have finished. Installation Regulations injury. Always use NEW flexible connectors when installing a gas appliance. Installation of this range must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, Important! ANSI Z223.1/NFPA.54, latest edition. - Page 28 INSTALLATION Check the appliance is electrically safe and gas sound when you have finished. the range, the area that the range will rest on should be built Checking the parts: up with plywood to the same level or higher than the floor 6 grates Allen key covering.
-
Page 29: Positioning The Range
INSTALLATION Check the appliance is electrically safe and gas sound when you have finished. Positioning the Range Fig. 8.1 Fig. 8.1 shows the minimum recommended distances and clearances from the range to nearby surfaces. Min 35½” (90 cm) - 36“ (91 cm) For Canada, min 36 / ”... -
Page 30: Fitting The Oven Handle
(Fig. 8.3). ArtNo.063-0019 - 90 - SC - Aga Professional - Removing the door Moving the Range The range is very heavy. Take great care. -
Page 31: Lowering The Two Rear Rollers
INSTALLATION Check the appliance is electrically safe and gas sound when you have finished. Lowering the Two Rear Rollers Fig. 8.6 To adjust the height of the rear of the range, first fit a 13 mm spanner or socket wrench onto the hexagonal adjusting nut (Fig. -
Page 32: Floor Fixing
INSTALLATION Check the appliance is electrically safe and gas sound when you have finished. Floor Fixing Fig. 8.10 Stability bracket Anti-tip bracket Using the screw supplied, assemble the anti-tip bracket base and anti-tip bracket extension (Fig. 8.9). Using suitable screws and fixings, attach the assembled anti- Cooker Range tip bracket to the floor to give a sufficient engagement into... -
Page 33: Electrical Connection
INSTALLATION Check the appliance is electrically safe and gas sound when you have finished. Electrical Connection Fig. 8.14 When installed the range must be electrically grounded in accordance with local codes or; in the absence of local codes 16” (41 cm) with the National Electrical Code ANSI/NFPA 70, latest edition. - Page 34 INSTALLATION Check the appliance is electrically safe and gas sound when you have finished. 4-Wire Conduit Installation Fig. 8.16 White Black Disconnect the supplied power cord from the terminal block Green and ground post. Keep the terminal block parts; you will need them.
- Page 35 INSTALLATION Check the appliance is electrically safe and gas sound when you have finished. 3-Wire Conduit Installation Fig. 8.22 Disconnect the supplied power cord from the terminal block and ground post. Keep the terminal block parts; you will need them. Remove the strain relief clamp from the power cord ArtNo.280-0039 Reducer Plate and remove the power cord and strain relief clamp from the mounting bracket.
-
Page 36: Gas Connection
INSTALLATION Check the appliance is electrically safe and gas sound when you have finished. Gas Connection Fig. 8.25 Installation of this range MUST conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1-latest edition. 16”... - Page 37 INSTALLATION Check the appliance is electrically safe and gas sound when you have finished. Connect the Range to the Gas Supply Fig. 8.28 Shut off the main gas supply valve before disconnecting the Appliance Flexible connector Adaptor gas inlet old range and leave it off until the new hookup has been completed.
-
Page 38: Seal The Openings
INSTALLATION Check the appliance is electrically safe and gas sound when you have finished. Seal the Openings Fig. 8.29 Seal any openings in the wall behind the range and in the floor under the range when hookups are completed. Important: When all connections are completed make sure the flow of combustion and ventilation air to the range is unobstructed. -
Page 39: Range Operational Checks
INSTALLATION Check the appliance is electrically safe and gas sound when you have finished. Range Operational Checks Refitting the Range Reverse the above procedure to refit. If the gas line has been Oven Check disconnected, check for gas leaks after reconnection. Turn on the oven and check that the oven fans start to turn Note: A suitably qualified person should disconnect and and that the oven starts to heat up. -
Page 40: To Fit The Drawer
INSTALLATION Check the appliance is electrically safe and gas sound when you have finished. To fit the drawer To remove the drawer DO NOT use the levers to remove the drawer... -
Page 41: Conversion To Another Gas
This appliance is supplied set for Natural gas. A conversion kit for Propane gas is supplied with the range. ArtNo.272-0025 - 90 Aga Professional - Control panel removal If the appliance is to be converted this must be done before installation. -
Page 42: Valve Adjustment
CONVERSION Check the appliance is electrically safe and gas sound when you have finished. Valve Adjustment ArtNo.0102-0011 - Screwing Fig. 9.3 the control valve bypass screw Disconnect from the electricity supply. Pull off all the control knobs. Open the oven door and remove the 3 fixing screws underneath the control panel (Fig. -
Page 43: Stick On Label
CONVERSION Check the appliance is electrically safe and gas sound when you have finished. Type 2 Fig. 9.7 The regulator has a bayonet mounted top cap (Fig. 9.7). Using a small coin, press in and turn the cap to remove it. Turn the cap over so that the letters “LP”... -
Page 44: 10. Circuit Diagram
10. Circuit Diagram A2/B1 B2 Code Description Code Description Code Color Multi-function oven master switch Oven protect thermostat Blue Multi-function oven drone switch Oven neon Brown Oven thermostat Oven light Black Oven front switch Oven light switch Orange Right-hand oven base element Door lock neon Right-hand oven top outer element Ignition spark generator... -
Page 45: 11. Rating Plate
CONVERSION Check the appliance is electrically safe and gas sound when you have finished. 11. Rating Plate Removing the Drawer (Access to rating plate) Fig. 11.1 NOTE: To avoid exterior damage to the storage drawer. Place a soft cushioned mat on the floor. Push the ends of the plastic clips (Fig. -
Page 46: 12. Technical Data
12. Technical Data INSTALLER: Please leave these instructions with the user. RATING PLATE LOCATION: Inside base drawer of cavity. To remove the drawer refer to the instructions in “Rating Plate” on page 43. COUNTRY OF DESTINATION: USA, Canada. Connections ArtNo280-0090 Drawer Cavity & Badges Electric 240 V 60 Hz ½”... - Page 47 AGA warrants the oven heating elements against defects in material or workmanship for an additional two years. These parts will be repaired or replaced at the option of AGA without charge, but you pay for labor and transportation subject to the terms and conditions set out below.
- Page 48 AGA Marvel 1260 E. VanDeinse St. Greenville, MI 48838 Business (616) 754-5601 Fax (616) 754-9690 Toll Free Telephone 800-223-3900 www.aga-ranges.com...