Hardy Process Solutions HI 2160RC PLUS Operation And Installation Manual page 9

HI 2151/30WC MANUAL
CHAPTER 5
CHAPTER 6
II
FIG. 4-7 REMOTE FUNCTION OPTION - - - - - - - - - - - - - - - - - - 4-7
FIG. 4-8 JUMPER SETTINGS FOR ANALOG INPUT PWA AND F1 FUSE - 4-9
FIG. 4-9 CONNECTOR PINS FOR ANALOG INPUT PWA - - - - - - - - - 4-10
FIG. 4-10 GROUND JUMPER TO READ ANALOG INPUT - - - - - - - - - - 4-11
FIG. 4-11 RS-422 CONVERTER DIP SWITCHES - - - - - - - - - - - - - - 4-12
FIG. 4-12 CONFIG. DIP SWITCHES REAR PANEL - - - - - - - - - - - - - 4-13
FIG. 4-13 OPERATIONAL DISPLAY #1 CURRENT WEIGHT - - - - - - - - 4-14
FIG. 4-14 REMOVAL OF REAR PANEL - - - - - - - - - - - - - - - - - - - 4-15
FIG. 4-15 REMOVAL OF TOP PANEL- - - - - - - - - - - - - - - - - - - - 4-15
FIG. 4-16 SETTING WAVERSAVER JUMPERS - - - - - - - - - - - - - - - 4-16
CALIBRATION- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-1
FIG. 5-1 PROPERLY INSTALLED LOAD CELL W/NO BINDING - - - - - - 5-2
FIG. 5-2 OPERATIONAL DISPLAY/NOT RUNNING - - - - - - - - - - - - 5-10
FIG. 5-3 OPERATIONAL DISPLAY RUNNING - - - - - - - - - - - - - - - 5-11
FIG. 5-4 OUTPUT SIGNAL IN 00.1% INCREMENTS - - - - - - - - - - - - 5-11
FIG. 5-5 OUTPUT SIGNAL IN 10% INCREMENTS - - - - - - - - - - - - - 5-12
FIG. 5-6 OPERATIONAL DISPLAY UNIT PAUSED - - - - - - - - - - - - - 5-13
FIG. 5-7 OPERATIONAL DISPLAY OFF - - - - - - - - - - - - - - - - - - 5-13
FIG. 5-8 AUTO RATE CALIBRATION PASSED - - - - - - - - - - - - - - 5-16
FIG. 5-9 AUTO RATE CALIBRATION FAILED - - - - - - - - - - - - - - - 5-17
FIG. 5-10 OPERATIONAL DISPLAY #1 CURRENT WEIGHT - - - - - - - - 5-19
FIG. 5-11 SCALE DISPLAY - - - - - - - - - - - - - - - - - - - - - - - - - 5-19
SETUP- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-1
FIG. 6-1 PRESS CONFIG/1 BUTTON TO GET TO THE MAIN MENU- - - - 6-4
FIG. 6-2 SECURITY CODE ENTRY DISPLAY - - - - - - - - - - - - - - - 6-4
FIG. 6-3 SELECTING SECURITY SUB-MENU - - - - - - - - - - - - - - - 6-5
FIG. 6-4 SECURITY MENU, SELECTING ACCESS LEVELS - - - - - - - - 6-5
FIG. 6-5 SECURITY MENU, ENTERING LEVEL VALUES - - - - - - - - - 6-7
FIG. 6-6 ACT BLANK TIMEBASE ERROR - - - - - - - - - - - - - - - - - 6-9
FIG. 6-7 DERIVED LOSS OF WEIGHT SLOPE (INTERPRETED AS
GAIN-IN-FIGWEIGHT)- - - - - - - - - - - - - - - - - - - - - - 6-10
FIG. 6-8 DERIVED LOSS OF WEIGHT SLOPE (INTERPRETED AS
NO CHANGE-IN-WEIGHT) - - - - - - - - - - - - - - - - - - - - 6-10
FIG. 6-9 DERIVED LOSS OF WEIGHT SLOPE (INTERPRETED AS
LOSS-IN-WEIGHT - - - - - - - - - - - - - - - - - - - - - - - - 6-11
FIG. 6-10 ENTERING TIMEBASE PARAMETER - - - - - - - - - - - - - - 6-13
FIG. 6-11 SETTING THE AVRG AND REC LEVELS - - - - - - - - - - - - - 6-14
FIG. 6-12 OPERATING DISPLAY TOTAL WEIGHT - - - - - - - - - - - - - 6-15
FIG. 6-13 ENTERING CALCULATED CONSTANT VALUES - - - - - - - - - 6-17
FIG. 6-14 OPERATIONAL DISPLAY/REC STATUS - - - - - - - - - - - - - 6-18
FIG. 6-15 GROUNDING THE "A" PIN TO CLEAR ALARM - - - - - - - - - - 6-21
FIG. 6-16 RATE TOLERANCES MENU/SHUTOFF SETTINGS - - - - - - - 6-22
FIG. 6-17 PROCESS GRAPH USING RATE TOLERANCES - - - - - - - - - 6-23
FIG. 6-18 AUTO REFILL OUTPUT RELAY - - - - - - - - - - - - - - - - - 6-24
FIG. 6-19 AUTO REFILL MENU/START AND STOP SETTINGS - - - - - - - 6-25
FIG. 6-20 AUTO REFILL MENU/LO SHUTOFF SETTINGS - - - - - - - - - 6-27
FIG. 6-21 AUTO REFILL MENU/HI SHUTOFF SETTINGS - - - - - - - - - - 6-28
FIG. 6-22 AUTO REFILL MENU/SETTING THE REFILL CORRECTION
FACTOR- - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-29
FIG. 6-23 GROUNDING REFILL FOR FORCED REFILL- - - - - - - - - - - 6-30
FIG. 6-24 MAIN MENU/SETTING TIME AND DATE - - - - - - - - - - - - - 6-30
FIG. 6-25 TIME AND DATE MENU/SETTING TIME AND DATE - - - - - - - 6-31
FIG. 6-26 MAIN MENU/SELECTING SERIAL PORT #1 - - - - - - - - - - - 6-32