Hardy Process Solutions HI 2160RC PLUS Operation And Installation Manual page 212

Selecting Operational Displays
Selecting the Auto Refill Function
Selecting the Initial Fill Function
1-4
Self Test
self-Test Count Up Sequence
7-2
Serial Commands
1-4
Serial Communications
Serial Communications/Serial Port #1 Sub-Menu (For
RS-232C Specifications See Chapter 2)
7-1
Serial Protocol
Serial Protocol and Serial Commands
8-24
Set Point High (SPH)
6-15
Set the OP% to 99.9%
Set the Operating Percentage for 10% increments
Setting a Percentage of the HI Output Signal
Setting Control Out HI%
5-14
Setting REC to Zero
Setting the Alarm Time (Sec.)
Setting the Automatic Rate Control Mode (Gravimetric
8-15
Mode)
Setting the Averaging Parameter (See Fig. 8-25)
Setting the Batch Decimal Point
Setting the Continuous Operation Mode
Setting the Control Out LO%
Setting the Control Out LO% and Control Out HI%
6-31
Setting the Date
Setting the Dip Switches
8-11
Setting the Flow Rate
Setting the Graduations
Setting the HI Alarm Tolerance
Setting the HI and LO Shutoff
Setting the HI Output Signal parameter
Setting the HI Shutoff Weight
6-27
4-4
Setting the Jumpers
Setting The Jumpers in the HI 2160PLUS
Setting the Jumpers in the Optional Quad Expander
4-5, 4-8
Box
Setting the LO ALARM Tolerance
Setting the LO Output Signal Parameter
Setting the LO SHUTOFFand HI SHUTOFFAlarm
6-26
Weight Parameters
Setting the LO SHUTOFF Weight
6-26
Setting the Manual Rate Control Mode (Volumetric
8-11
Mode)
5-3
Setting the Mass Units
Setting the Rate Decimal Points
Setting the Rate Exception Control (REC LEVEL)
Setting the Rate Exception Control Parameters.
Setting the Remote Set Point Input Mode
Setting the Security Code Numbers
Setting the Set Point Amount Batch Mode
Setting the Set Point High (SPH) Parameter.
Setting the Shutoff Out Percentage
Setting the START (LO) and STOP (HI) Parameters
26
8-1
6-25
6-28
4-13
6-31
7-1
8-23
6-43
6-20
5-4
8-18
6-40
4-11
5-5
6-20
6-21
8-21
4-4
6-19
8-20
5-4
8-29
8-14
6-6
8-16
8-24
6-22
Setting the Sticker Value
Setting the Time
Setting the Time Units (Rate of Flow)
Setting the Total Decimal Point
Setting Too High
Setting UP the Analog Output Option
Setting Up the Controller for Manual Tuning
8-25
Setup
Sigma Data - About 2 Sigma Data
Sigma Test - Definition
Slave Controller
Slow Feed Rate
Solid State Relays
8-14
Some Things to Remember When Changing the Jump-
4-17
er Settings
SPAN Calibration Procedures
SPAN Output Reference Voltage and Current
Specific Response Error Codes
Speed Control Output Card (Prt. #0535-0406)
Speed Control Output Wiring Diagram (See Fig. 3-22)
8-21 3-15
9-2
Start Up
Status, Force Functions, Weight and Rate Parameters
7-11
6-40
Sticker Number
5-8
Sticker Value
2-1
Storage
7-7
SUB-CMD
System Configuration
System Lock Ups
System Network Configuration
System Troubleshooting
T
Test Procedures
The Information Type Parameter Setting
The Instrument Does the Following
The Manual Rate Calibration is Complete
The Rate Section
8-3
The Set Rate
The Weight Section
There are Three Continuous Rate Displays
Three Constants
K(p), K(i), K(d)
Time and Date Sub-Menu
6-9
Time Base
Time Unit Selection
Total Accumulated Weight
8-29
Total Decimal Point Menu
Total Weight Display
Troubleshooting with a Simple Ground Test.
Tuning and Control Sub-Menu
Tuning/Control (Sec) Parameter Definitions
Tuning/Control Menu
Twisted Pair Shielded
6-
1-4
Two Sigma
5-8
6-30
5-4
5-5
6-45
6-45
8-34
8-30
8-18
5-21
4-1
5-7
7-10
5-8
7-1
9-4
7-1
9-3
8-30
5-15
8-3
8-3
6-12
6-30
5-4
8-7
5-5
8-3
6-8
4-17
3-17
Index
6-13
6-47
4-2
6-47
5-23
8-1
9-5
6-9