Hardy Process Solutions HI 2160RC PLUS Operation And Installation Manual page 10

CHAPTER 7
CHAPTER 8
FIG. 6-27 SERIAL PORT #1 CONFIGURATION - - - - - - - - - - - - - - - 6-32
FIG. 6-28 SERIAL PORT #1 CONFIGURATION - - - - - - - - - - - - - - - 6-33
FIG. 6-29 OPERATIONAL MENU - - - - - - - - - - - - - - - - - - - - - - 6-33
FIG. 6-30 DISABLING THE PRINT FUNCTION - - - - - - - - - - - - - - - 6-35
FIG. 6-31 CONFIG DIP SWITCH #3/DISABLING BATCH REPORT PRINTING
FUNCTION - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-36
FIG. 6-32 SAVING TO SECURE MEMORY MODULE - - - - - - - - - - - - 6-38
FIG. 6-33 SAVE/RECALL MENU - - - - - - - - - - - - - - - - - - - - - - 6-38
FIG. 6-34 RECALL SUB-MENU - - - - - - - - - - - - - - - - - - - - - - - 6-40
FIG. 6-35 CONTROL OUT% GRAPH - - - - - - - - - - - - - - - - - - - - 6-41
FIG. 6-36 TUNING/CONTROL MENU/SETTING CONTROL OUT LO
PERCENTAGE - - - - - - - - - - - - - - - - - - - - - - - - - 6-42
FIG. 6-37 TUNING/CONTROL MENU/ SETTING CONTROL OUT LO
PERCENTAGE TO 26 - - - - - - - - - - - - - - - - - - - - - - 6-43
FIG. 6-38 TUNING/CONTROL MENU/SETTING CONTROL OUT HI
PERCENTAGES - - - - - - - - - - - - - - - - - - - - - - - - - 6-44
FIG. 6-39 TUNING/CONTROL MENU/SETTING CONTROL OUT HI
PERCENTAGE/74 - - - - - - - - - - - - - - - - - - - - - - - - 6-45
FIG. 6-40 MAIN MENU/ANALOG OUTPUT - - - - - - - - - - - - - - - - - 6-46
FIG. 6-41 ANALOG OUTPUT MENU - - - - - - - - - - - - - - - - - - - - 6-46
FIG. 6-42 ANALOG OUTPUT MENU/ZERO AND SPAN VOLTAGE
SETTING - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-48
SERIAL COMMUNICATIONS - - - - - - - - - - - - - - - - - - - - - - - - 7-1
FIG. 7-1 MULTIDROP CONFIGURATION WITH HOST AND
CONTROLLERS - - - - - - - - - - - - - - - - - - - - - - - - - 7-2
OPERATION- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8-1
FIG. 8-1 RATE & CURRENT WEIGHT DISPLAY (DEFAULT DISPLAY)- - - 8-1
FIG. 8-2 RATE & TOTAL WEIGHT DISPLAY - - - - - - - - - - - - - - - - 8-2
FIG. 8-3 CURRENT TOTAL WEIGHT DISPLAY - - - - - - - - - - - - - - 8-2
FIG. 8-4 RATE DISPLAY - - - - - - - - - - - - - - - - - - - - - - - - - 8-3
FIG. 8-5 TOTAL ACCUMULATED WEIGHT - - - - - - - - - - - - - - - - 8-4
FIG. 8-6 CURRENT AND ACCUMULATED TOTAL WEIGHT DISPLAY - - - 8-5
FIG. 8-7 SET POINT MENU/SELECTING BATCH MODE - - - - - - - - - 8-5
FIG. 8-8 BATCH AMOUNT AND RATE DISPLAY - - - - - - - - - - - - - 8-6
FIG. 8-9 BATCH AMOUNT/CURRENT WEIGHT DISPLAY - - - - - - - - - 8-7
FIG. 8-10 BATCH AMOUNT AND TOTAL WEIGHT DISPLAY - - - - - - - - 8-8
FIG. 8-11 SET RATE/CURRENT WEIGHT DISPLAY PARAMETERS - - - - 8-8
FIG. 8-12 CURRENT/TOTAL WEIGHT DISPLAY PARAMETERS - - - - - - 8-9
FIG. 8-13 CLEARING THE TOTAL REGISTER FROM THE FRONT PANEL - 8-10
FIG. 8-14 CLEARING TOTAL REGISTER FROM THE REAR PANEL - - - - 8-10
FIG. 8-15 OPERATIONAL DISPLAY RUNNING - - - - - - - - - - - - - - - 8-12
FIG. 8-16 OUTPUT SIGNAL IN 00.1% INCREMENTS - - - - - - - - - - - - 8-13
FIG. 8-17 OUTPUT SIGNAL IN 10% INCREMENTS - - - - - - - - - - - - - 8-14
FIG. 8-18 SELECTING THE REMOTE MODE OF OPERATION - - - - - - - 8-15
FIG. 8-19 SETPOINT MENU/SELECTING AUTOMATIC MODE - - - - - - - 8-16
FIG. 8-20 SETPOINT MENU/CONTINUOUS AMOUNT MODE- - - - - - - - 8-17
FIG. 8-21 SETPOINT MENU/SET POINT AMOUNT BATCHING - - - - - - - 8-17
FIG. 8-22 PROCESS CONTROL SYSTEM/RATIO CONTROL - - - - - - - - 8-19
FIG. 8-23 REMOTE SET POINT JUMPER- - - - - - - - - - - - - - - - - - 8-20
FIG. 8-24 SETTING LO AND HI SIGNAL OUTPUT PARAMETERS - - - - - 8-21
FIG. 8-25 REMOTE SETPOINT MENU/SETTING AVERAGING - - - - - - - 8-22
FIG. 8-26 REMOTE SETPOINT MENU/SETTIN SPL & SPH - - - - - - - - - 8-23
FIG. 8-27 ANALOG SIGNAL CONFIGURATION DIAGRAM - - - - - - - - - 8-27
FIG. 8-28 DOWNLOADING SET POINTS, RELAY WIRING
Table of Illustrations
III