Hardy Process Solutions HI 2160RC PLUS Operation And Installation Manual page 211

HI 2151/30WC MANUAL
8-23
Percentage Function
Performing the HIGH RATE data sampling.
Physical Characteristics
5-2
Platform Scale/Feeder
4-3
PLC,
4-2
Potentiometers
Power and Relay Circuit Card Filters
Power and Utility Requirements
Power Brown Outs or Black Outs
9-5
Power Spikes
9-6
Power Surges
4-13
Power Up Process
Pre Power Up Check Procedures
6-12
Pre-Act Corr.
Pre-Calibration Procedures
6-33
Printer Setup
6-35
Printing Batch Reports
Process Example using Rate Tolerances (See Fig. 6-
6-23
17)
PROFIBUS Error Codes for C2 Calibration
PROFIBUS Error Codes for Rate Calibration
PROFIBUS Interface Card
PROFIBUS Interface Option
PROFIBUS Interface Option (-B4)
Profibus Interface Option Card
PROFIBUS Option card
Programmable Logic Controller
Proper Power Up Indicators
Q
Quad Option Expander Box - Basic Function (See Fig.
2-3
1-3)
R
Rate and Total Weight Display
Rate Calibration Data Gathering Form
Rate Calibration Passes
Rate Calibration Process
1-2
Rate Control Algorithm
8-28
Rate Exception Control
Rate Exception Control (REC) Alarm
Rate Exception Control (REC) Alarm appears too often
9-12
Rate Exception Control Shutoff
8-11
Rate Modes
4-2
Rate of Change (ROC)
8-2
Rate Section
8-8
Rate Set Point
4-7
Rate Set point
7-11
Rate Tolerance
1-2
Rate Tolerance Alarm
Rate Tolerance Sub-Menu
RateCurrent Weight Display Parameters (See Fig. 8-
8-8
11)
Ratio Control (Master/Slave)
Ratio Control Application Example
5-20
2-2
3-17
2-2
9-6
4-13
5-1
9-15
9-16
8-19
3-22
4-11
2-3
3-13
7-1
4-13
8-1
5-20
5-17
5-9
1-2
6-12
6-19
8-18
8-25
Ratio Process Control System
Readings on the Display are Not Correct
Rear Panel Config. Option Dip Switch Settings
1-2
REC Alarm
5-18, 6-11, 8-29
REC Level
6-12
REC Shutoff
6-12
REC Time
Recommended Graduation Level
Recommended Installation Procedures
Refill and Alarm Relays
Refill and Alarm Relays Diagram (See Fig. 3-23)
6-24
Refill Condition
4-13
Relay Output Wire
Remote Control Options
Remote Function Inputs
Remote Functions Connector
Remote functions Connector
Remote Functions Wiring
Remote Functions Wiring Diagram (See Fig. 3-25)
Remote I/O Interface for the Allen Bradley Network
22
Remote I/O Interface for the Allen Bradley Network Op-
4-11
tion (-B2)
1-4
Remote Operation
Remote Set Point Analog Input Option Card
Remote Set Point Input Option - Basic Function
Remote Set Point Input Option Board
Remote Set Point Input Option Card Configuration (Prt.
4-7
#0535-0410)
Remote Set Points Option for Ratio Control Applications
8-19
Remote Setpoint Input Card
Remote Setpoint Option Wiring Diagram (See Fig. 3-27)
3-18
1-4, 2-2
Reports
8-10
Reset Total ("RstToT")
6-12
Restore Data
Restoring Data Saved in the Secure Memory Module
39
RFI (Radio Frequency Interference)
RS 232 Port Wiring Diagram (See Fig. 3-24)
RS-232 to RS-422 Converter Board Option
RS-422 Converter Option Wiring Diagram (See Fig. 3-
3-18
28)
RS422/485 (Serial Port Option) - Basic Function
S
7-10
S (Set) Command
6-12
Save Data
SAVE/RECALL SUB-MENU
Saving to the Secure Memory Module (SMM)
Secure Memory Module
Secure Memory Module (SMM)
6-3
Security Access Levels
Security Code Number Has Not Been Assigned
6-3
Security Sub-Menu
Selecting Batch Displays
8-18
9-13
4-12
5-5
3-14
4-1
2-1
4-6
8-19
8-10
4-13
8-18
2-2
8-14
9-14
9-4
3-16
2-4
6-39
6-37
1-3
3-24, 5-8
5-10
8-5
3-16
3-17
3-
6-
2-2