Hardy Process Solutions HI 2160RC PLUS Operation And Installation Manual page 4

Chapter 5
PROFIBUS Interface Option (-B4) - - - - - - - - - - - - - - - - - - - - - - 4-11
Changing the RS-422 Converter Port Option (-B1) - - - - - - - - - - - - - - 4-11
Setting the Dip Switches - - - - - - - - - - - - - - - - - - - - - - - - - 4-11
Rear Panel Config. Option Dip Switch Settings - - - - - - - - - - - - - - - - 4-12
Option Configuration Dip Switch - - - - - - - - - - - - - - - - - - - - - 4-12
Power Up Process - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-13
Pre Power Up Check Procedures - - - - - - - - - - - - - - - - - - - - - 4-13
Proper Power Up Indicators - - - - - - - - - - - - - - - - - - - - - - - 4-13
®
WAVERSAVER - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-14
Effects of Vibration on a Scale - - - - - - - - - - - - - - - - - - - - - - 4-14
Configuring WAVERSAVER - - - - - - - - - - - - - - - - - - - - - - - 4-14
Some Things to Remember When Changing the Jumper Settings - - - - - 4-17
Calibration - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-1
About Chapter 5 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-1
Pre-Calibration Procedures - - - - - - - - - - - - - - - - - - - - - - - - - - 5-1
Mechanical Check Procedures - - - - - - - - - - - - - - - - - - - - - - 5-1
Checking the Load Cell Installation - - - - - - - - - - - - - - - - - - 5-1
Check for Binding on the Load Cell - - - - - - - - - - - - - - - - - - 5-1
Check for Binding on Platform Scale/Feeder - - - - - - - - - - - - - 5-2
Electrical Check Procedures - - - - - - - - - - - - - - - - - - - - - - - 5-2
Load Check - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-2
Weight Calibration Process - - - - - - - - - - - - - - - - - - - - - - - - - - 5-3
Calibration Setup Procedures - - - - - - - - - - - - - - - - - - - - - - 5-3
Setting the Mass Units - - - - - - - - - - - - - - - - - - - - - - - - 5-3
Setting the Time Units (Rate of Flow) - - - - - - - - - - - - - - - - - 5-4
Setting the Rate Decimal Points - - - - - - - - - - - - - - - - - - - 5-4
Setting the Batch Decimal Point - - - - - - - - - - - - - - - - - - - 5-4
Setting the Total Decimal Point - - - - - - - - - - - - - - - - - - - - 5-5
Setting the Graduations - - - - - - - - - - - - - - - - - - - - - - - 5-5
C2® Calibration Process - - - - - - - - - - - - - - - - - - - - - - - - - 5-6
Hard Calibration Process (With Calibrated Test Weights) - - - - - - - - - 5-7
ZERO Calibration Procedures - - - - - - - - - - - - - - - - - - - - 5-7
SPAN Calibration Procedures - - - - - - - - - - - - - - - - - - - - 5-7
Setting the Sticker Value - - - - - - - - - - - - - - - - - - - - - - - - - 5-8
Rate Calibration Process - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-9
Feeder System Verification Procedures - - - - - - - - - - - - - - - - - - 5-9
Automatic Rate Calibration Procedures - - - - - - - - - - - - - - - - - - 5-14
Setting REC to Zero - - - - - - - - - - - - - - - - - - - - - - - - - 5-14
Enter the PAUSE TIME Value - - - - - - - - - - - - - - - - - - - - 5-14
Enter the PRIME TIME Value- - - - - - - - - - - - - - - - - - - - - 5-15
Enter the FEED TIME Value - - - - - - - - - - - - - - - - - - - - - 5-15
AUTO RATE CALIBRATION From the Front Panel - - - - - - - - - - 5-15
AUTO RATE CALIBRATION Using a Serial Command - - - - - - - - 5-15
The Instrument Does the Following - - - - - - - - - - - - - - - - - - 5-15
Manual Rate Calibration Procedures - - - - - - - - - - - - - - - - - - - 5-18
Gathering Rate Calibration Data Method #1- - - - - - - - - - - - - - 5-20
Materials Required - - - - - - - - - - - - - - - - - - - - - - - - 5-20
Gathering Rate Calibration Data Method #2- - - - - - - - - - - - - - 5-21
Materials Required - - - - - - - - - - - - - - - - - - - - - - - - 5-21
Slow Feed Rate - - - - - - - - - - - - - - - - - - - - - - - - - 5-21
High Feed Rate - - - - - - - - - - - - - - - - - - - - - - - - - 5-22
Entering the Calibration Values - - - - - - - - - - - - - - - - - - - - 5-22
Entering the rate data into the Rate Calibration sub-menu - - - - - 5-22
Entering the High Rate Calibration Data - - - - - - - - - - - - - 5-23
The Manual Rate Calibration is Complete- - - - - - - - - - - - - - - 5-23
Table of Contents
iii