Extron electronics IP Link Pro xi IPL EXP PDU4H User Manual page 24

Circuit Breaker
(power output
overcurrent protection)
Rear Panel
100 0 /240V ~ ~ 12/10A MAX
BREAKER
5 50 0 0-60 0-60 0-60 0-60 0-60 0-60 0 -60 0-60 -60 -60 -60 -60 -60 -60 -6 -60 -60 -60 -60 -60 -60 -60 -60 -60 -60 -60 6 60 6 60 60 6 0 0 H H H H H H H H H H H H z H H Hz
120 VAC or 240 VAC,
50-60 Hz
Input
Figure 7. Switched AC Power Output Ports
By default, the switched AC ports are in the unpowered (Off) state. During regular operation,
the states (On/Off) of the switched AC ports persists after a power cycle. The power output
state setting persists after and is retained during a power cycle.
Power sequencing
Power up sequencing prevents an in‑rush power overload. In the event of power loss
and restart, or any time two or more switched AC ports are turned on, power outlets are
powered on sequentially with a user‑configurable delay between each one. This prevents a
power overload spike and prevents a blown fuse or tripped circuit breaker.
A user cannot disable power sequencing, but you can reduce the time interval (between
ports turning on) to as low as
•
•
•
Surge protection
These outputs feature single‑stage surge protection using multiple MOVs to protect
connected products from power surges of up to 1750 joules (10/1000 µs).
1 2 3
To AC power input
ports on AV devices
0.1
Startup time interval — You can set a unique startup delay period that applies to every
switched AC port. For example, if you set the startup delay interval to be
then the second, third, and fourth ports in the power‑up sequence turn on at
0.5 1 1.5
seconds, second,
Sequence order — The power‑on sequence is always in ascending order, from output 1
to output 4. The only ways to change the order are to:
• Use configuration or programming.
• Select an output manually.
Use controls in the IPL EXP PDU4H embedded webpage.
•
Sequence persistence — The power on sequence occurs every time two or more AC
outlets are turned on. This occurs regardless of the source of the change in power
on‑off actions (program or configuration, SIS command, embedded webpage setting,
manual control selection, power cycling to the IPL EXP PDU4H).
Connect AC powered products to these four ports
using a standard IEC power cord, or use an Extron
IEC-to-Edison cable kit if your devices require
NEMA 5-15R receptacles.
4
• Output voltage: 120/240 VAC, 50-60 Hz
• Maximum AC load:
12 A at 120 VAC or 10 A at 240 VAC
• Current sense:
0 A to 12 A, 100 mA resolution, ≤6% tolerance
• Surge protection: Single-stage – multiple MOVs
• Surge energy dissipation: 1750 joules (10/1000 µs)
These outputs can be controlled via software,
controls in the embedded web page, SIS commands
(sent via SSH) or by a keypad or switch connected to
the Manual Control contact closure port.
Sortie Electrique Commutée
Connectez les produits alimentés à ces quatre ports à l'aide
d'un cordon électrique IEC standard, ou utilisez un lot de
câbles IEC/Edison Extron si vos appareils nécessitent des
prises NEMA 5-15R.
• Tension de sortie : 120/240 VAC, 50-60 Hz
• Charge CA maximale : 12 A à 120 VAC ou 10 A à 240 VAC
• Détection de courant : 0 A à 12 A, résolution 100 mA,
tolérance ≤6%
• Protection contre les surtensions : plusieurs
parasurtenseurs à un étage
• Dissipation de l'énergie en cas de surtension : 1 750 joules
(10/1 000 µs)
Plusieurs sorties peuvent être contrôlées via un logiciel, des
contrôles dans la page Web embarquée, des commandes SIS
(envoyées via SSH), ou via un clavier ou un switch connecté
au port de Manual Control avec contact sec.
second.
2
, and seconds, respectively.
IPL EXP PDU4H • Hardware Features and Installation
Switched AC Power Output
0.5
second,
16