Triumph TIGER Service Manual page 92

4. Ensure that the 3 locating dowels are in position in
the upper crankcase.
cc
1. Locating dowels
5. Apply a thin bead of silicone sealant to the lower
crankcase mating faces. (At the factory, Three Bond
12155 is used).
1. Sealer areas
.a:" r .
a., :, : r ^ :. 3 ::
uv 5 • v;:•' x W."' } i! :a a. .'` : •. !,si;;: •:,.{:Yv'
:;
:r}'^ :,^vnt t`Cihr >,"?tt^.'.n•:,,. fi
5.
,Q
fif ? '
5 " ^
Caution
,t
h♦
:
. :,
b. r 'u X
,
AS
CS:f ma
aMv. • , ^•• x... ^.: < "^
, ...:::n,..t.., ^...n^^A;^ ^n...,,....:....:.:,.,•.:..,^: ^`
rx, ..,h .. .vW:•. ,.. `l.' .::.: .:....
, A .tn. t^'t"..n n ..., .: .. ro..
:v:n.:,^^.i:..S,i<..:.SSV::y..:::..:..a^^,',.:?':, :k ::::.^,..... C' L.#.....::n.
":^?:
Do not use excessive amounts of sealer. The extra sealer
may become dislodged and could block the oil passages
in the crankcases causing severe engine damage.
6. Install and lubricate the crankshaft bearing shells
with clean engine oil (see bearing selection before
proceeding).
7. Lubricate the crankshaft journals with clean engine
oil.
MM
ii
:
a
:SYS.:' 4 R •.oi;:..?.:ADC, uxaY.a
Srh^.'.:'4r v: ' S',ti."
C Cy S•: C
(, 7' ^..`^9 f n.. .is •. c,^i
k
t.. A te..r:.l..
• r$t.' w.Y ,^• ,I,..L..> sth . sh ...nn:Sn.:s}.v::YC , i: ` ^o, . ..: ."...?.:}.v..r.n. x "
.r .t. ^.
q
Service Manual - Tiger
iiirii 1T
8. Locate a new oil gallery 0-ring to the upper
crankcase.
ccyr
't ^\ I! _ nti
0-ring
1.
Position the lower crankcase to the upper, ensuring
9.
that all selectors engage correctly. An assistant may
be required to support the crankcase during
alignment.
10. Fit the screws into the lower crankcase and hand
tighten until the bolt heads are near contact with the
crankcase.
11. Invert the engine.
12. Fit the screws into the upper crankcase and hand
tighten until the bolt heads are near contact with the
crankcase.
Note:
• The crankcase screws are tightened in
stages.
• Two different sizes of crankcase screw are
used. All screws are tightened through the
first stage of the tightening procedure but
only the M8 size screws are tightened at the
second stage.
, ,^^^
^^} <
it^ ^ ^m
5 ,? t r i
^^ ,:sf ^
♦ ♦ t
• •
Sii£ ' c` • u`Si: '^' Y '
"tee'"' 7t" ?,
•fit .,
3 5 ^autioii+'{^ 's..
n .# ... ,. a 5ff;` ' S,'s^":tb `L' v^
^
h ♦
^+1::: n f`^' • x' ^ J '.''?a:^:'ta•
..:......:> ...s::^;,t.t.::. amt..:: ^.....^::^.
i!5.?r: r :n3 "o. ^`S^+K,':}°k'SE• rc; ^., , > , t n stta»vtY.Y,' Y...
Failure to fo ow the correct screw tightening sequence
ll
may result in permanent crankcase damage.
Stage I - all screws
1. Invert the engine.
I
ti ii iiii
.
If
y ♦, ^•
t
e :.d .
u..
p
^ # . 4..
T. f ^•
S f+
Nt '1
c
^
, `^5 f
a
.^•` M1 73' f
^. ^ "a`^,4:;
^;` s,; '.^.n««:, v}wsn. ^$:. v.,n t• t' .c.:. .: ,..{::f:. t: ..a•..
"D5:'. . 'i .. . r.)a..'Y.a... .» YL,.. . `^
5.5