Chicco BebeCare oasys i-Size Manual page 31

therefore a Class 1 product which can be used
in all European Union Countries.
The equipment works together with the Blue-
tooth® Low-Energy standard.
• Frequency ranges: 2.402 GHz – 2.480 GHz
ISM band;
• Channels: 40 channels, each with a band with
equal to 2 MHz;
• Transmission power: - 4 dBm (transmitted to
the antenna);
• Maximum power; 0.398 mW;
• Standard Radio: 802.15.1;
The Chicco BebèCare "Safety system for chil-
dren in the car" was developed based on the in-
vention made by the engineer Stefano Fontana.
4. ADDITIONAL OPERATIONS
4.1 PLACING THE CHILD IN THE CHILD
CAR SEAT AND ADJUSTING THE SAFETY
HARNESS
To adjust the harness straps, proceed as follows:
1. Press the adjustment button and pull the child
car seat harness straps to loosen them (Fig. 19).
2. Press the red button (Fig. 20) to open the
buckle.
3. Place the baby on the seat.
WARNING! The harness straps must always
be adjusted to adapt to the child's growth
phase. Before installing the child car seat in-
side the vehicle, adjust the harness straps to
the right height. To adjust them correctly, the
harness straps must come out from the back-
rest at the height of the child's shoulders. The
headrest and straps can be adjusted simul-
taneously in height to 6 different positions
using button X to follow your child's growth.
4. Overlap the two ends of the harness straps,
insert them together inside the buckle until
you hear them clicking (Fig. 21)
WARNING! Never insert just one end of the
harness into the buckle or insert them one at a
time. Press button Q to adjust the straps.
5. Tighten the child car seat's safety harness by
pulling the adjustment strap (Fig. 22).
WARNING! The reducer cushion guarantees
the correct support and the ideal position for
the neck and back of babies from when they
are born until they weigh about 6 kg.
4.2 USE AS RECLINED CRADLE
When the child car seat is not used in a car, it
can be used as a reclined cradle.
Place on stable horizontal surfaces only.
WARNING! Before carrying the child car seat,
always move the carry handle to position B
(vertical).
WARNING! Do not leave the child unattended.
WARNING! Always use the restraint system.
WARNING! Using the child car seat on raised
surfaces such as tables, chairs etc. can be dan-
gerous.
WARNING! This child car seat is not designed
for long periods of sleep.
WARNING! Do not use the seat when the
child is able to sit up independently.
This child car seat is not a replacement for a bed
or crib. Should your child need to sleep, place
your child in a suitable bed or cot. Do not use
the child car seat if any part is broken or missing.
4.3 USE WITH THE STROLLER
The Oasys i-Size child car seat can only be used
with LOVE UP - StyleGo UP strollers.
WARNING! Please read the Stroller instruction
manual when using the child car seat on the
stroller.
Before fastening the child car seat, remove the
stroller seat.
To install the child car seat on the stroller, pro-
ceed as follows:
- Hold the child car seat with the handle in the
vertical position (Fig. 1 - B) (Fig. 23).
- Fit the connecting points (U) into the slots
on the stroller (Fig. 24A – LOVE UP, Fig. 24B –
StyleGo UP ). Pay particular attention that the
seat is engaged on both sides. You will hear a
CLICK when it is fastened correctly.
WARNING: Before use, make sure that all the
child car seat fastening devices are correctly
engaged.
To remove the child car seat from the stroller:
1. Put the carry handle into vertical position
(Fig. 1 - B).
2. Pull first the rear release handle (W), then lift
the child car seat by the handle (Fig. 25A -
LOVE UP, Fig. 25B - StyleGo UP).
31