Mitsubishi Electric e Series Service Handbook page 67

[ IV Remote Controller ]
<5> Function Settings
The settings for the following remote controller functions can be changed using the remote controller function
selection mode. Change the settings as necessary.
Item 1
1. Display language Display language selection
setting
("CHANGE
LANGUAGE")
2. Function lock (1) Function lock ("LOCKING FUNCTION")
settings
(2) Operation mode skip setting ("SELECT MODE").
("FUNCTION
SELECTION") (3) Temperature range limit setting ("LIMIT TEMP FUNCTION")
3. Basic function
(1) Remote controller main/sub setting ("CONTROLLER MAIN/
settings
SUB")
("MODE SELEC-
TION")
(2) Use of clock setting ("CLOCK")
(3) Timer function setting ("WEEKLY TIMER")
(4) Contact number setting ("CALL.")
(5) Temp offset setting ("TEMP OFF SET FUNCTION")
4. Display options (1) Temperature unit °C/°F setting ("TEMP MODE °C/°F")
("DISP MODE
(2) Water temperature display setting ("WATER TEMP DISP
SETTING")
SELECT")
Function setting flowchart
[1] Stop the unit and go into the remote controller function selection mode. → [2] Select from item 1. → [3] Select from
item 2. → [4] Make the setting. → [5] Return to the Normal Operation screen.
Normal Operation screen (Screen that appears when
the unit is not running)
(Press and hold the
* No settings can be changed during a test run and self-
diagnosis.
Item 1
Press the
Display language
("CHANGE LANGUAGE")
Press the
button.
E
Function lock
("FUNCTION
Press the
SELECTION")
button.
G
Press the Press the
E button. E button.
Press the
G button.
Basic functions
("MODE
SELECTION")
Press the
button.
E
Press the
G button.
Display options
("DISP MODE
SETTING")
HWE1417B
Item 2
E D
and buttons for two seconds.)
Remote Controller Function
Selection Mode
G
button.
Item 2
Function lock setting ("LOCKING FUNCTION")
Operation mode skip setting ("SELECT MODE")
Temperature range limit setting ("LIMIT TEMP FUNCTION")
Remote controller main/sub setting ("CONTROLLER MAIN/SUB")
Use of clock setting ("CLOCK")
Timer function setting ("WEEKLY TIMER")
Contact number setting ("CALL.")
Temp offset setting ("TEMP OFF SET FUNCTION")
Temperature unit °C/°F setting ("TEMP MODE °C/°F")
Water temperature display setting ("WATER TEMP DISP SELECT")
• Use to select the display language from available languages.
• Use to lock functions.
• Use to show or hide specific modes.
• Use to restrict the temperature range.
• Use to designate the remote controller as Main or Sub.
*When two remote controllers are connected to one group, one
controller must be set to sub.
• Use to enable or disable the clock.
• Use to select a timer type.
• Use to show or hide, or enter the emergency contact number.
• Use to show or hide the offset value.
• Use to show or hide the temperature unit (°C or °F).
• Use to show or hide the water temperature.
E
(Press and hold the and
for two seconds.)
* The changes made to the settings will
be saved on the remote controller.
Press the
Press the button.
G
D button.
Press the
D button.
Press the button.
G
Press the
button.
D
Press the button.
G
- 58 -
Item 3 (Setting content)
D
buttons
See <5>-1
Dot display
The texts will appear in the
Item 3
selected language. In this
See <5>-2. (1)
manual, the texts are in English.
See <5>-2. (2)
See <5>-2. (3)
See <5>-3. (1) F
TEMP.
See <5>-3. (2)
MENU
E
BACK MONITOR/SET
See <5>-3. (3)
PAR-W21MAA CLOCK
G
See <5>-3. (4)
See <5>-3. (5)
C
See <5>-4. (1)
See <5>-4. (2)
I
ON/OFF
A
ON/OFF INITIAL SETTING CIR.WATER
DAY CHECK TEST
CLEAR
B
D H
GB