Safety Instructions - Night Owl WNIP2 Series User Manual

Wi-fi nvr
Hide thumbs Also See for WNIP2 Series:
Table of Contents

Advertisement

Safety Instructions

Use the provided power adapter.
Do not use this product with a power source that applies more than the specified voltage.
Never insert metal into the Wi-Fi NVR case or its openings.
Inserting metal into the Wi-Fi NVR case may cause electric shock.
Do not operate in wet or dusty areas.
Avoid placing the Wi-Fi NVR in areas such as a damp basement or dusty attic.
Do not expose the Wi-Fi NVR to rain or use near water.
If the Wi-Fi NVR accidentally gets wet, unplug it and contact technical support immediately.
Keep product surfaces clean and dry.
To clean the outside case of the Wi-Fi NVR, use a lightly dampened cloth. Do not use
cleaning solutions or solvents.
Do not install near any heat sources.
Do not install the Wi-Fi NVR near any heat sources such as stoves, heat registers, radiators,
or electronics (including amplifiers) that produce heat.
Unplug the Wi-Fi NVR when moving it.
Make sure that the Wi-Fi NVR is unplugged before you move it. When moving this device, be
sure to handle it with care.
Make sure there is good air circulation around the Wi-Fi NVR.
This Wi-Fi NVR uses an internal hard drive, that generates heat during operation for video
storage. Do not block the vents on the Wi-Fi NVR as these vents reduce the generated heat
while the system is running. Place this product in a well-ventilated area.
Do not attempt to remove the top cover.
If you observe any abnormal operation, unplug the Wi-Fi NVR immediately and contact
technical support. Do not attempt to open the Wi-Fi NVR to diagnose the cause of the
problem. Removing the cover will void your warranty.
Handle the Wi-Fi NVR carefully.
If you drop the Wi-Fi NVR on any hard surface, it may damage the device. If the Wi-Fi NVR
doesn't work properly due to physical damage, contact an authorized dealer for repair.
It is recommended to use your Wi-Fi NVR with an uninterruptible power supply (UPS).
Connecting your Wi-Fi NVR and cameras to a UPS allows continuous operation even during
power outages. The run-time duration will depend on the rating of the UPS used.
CAUTION
You may be subjected to severe electrical shock if you remove the cover of the Wi-Fi NVR.
Support.NightOwlSP.com
1

Hide quick links:

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the WNIP2 Series and is the answer not in the manual?

Questions and answers

Jerry Fisher
January 23, 2025

I have model WNIP-2LTA-BS-U stand alone camera. I previously had this device in use for my garage. we had to change routers and now have different password. I **** not able to get the camera connected

Glenn Jones
April 11, 2025

I need help with getting the phone on the App

User image 67f9932125b80
1 comments:
Mr. Anderson
April 11, 2025

To connect your Night Owl WNIP2 Series camera to the app:

1. Open the Night Owl Protect app.
2. Tap "Add New" and select "Standalone Camera."
3. Tap "OK" to allow the app to scan the camera’s QR code.
4. Tap "Use Your Network to Discover Your Device," then tap "OK."
5. Tap "Use Your Network to Discover Your Device" again.
6. Tap on the detected device and confirm by tapping "Yes."
7. Go to your device settings, tap "Wi-Fi," and connect to the network starting with "noip."
8. Once connected (checkmark appears), return to the app.
9. The app will search for the camera automatically.
10. Select your Wi-Fi network, enter the password, and tap "Continue."
11. When the screen says "Device has been added" and the camera says "Woohoo," setup is complete.
12. Name the camera and tap "Live View" to see the live stream.

This answer is automatically generated

This manual is also suitable for:

Wnvr-wnip2

Table of Contents

Save PDF