Page 1
Mod. 1099 DS1099-047A H.265 5M PRO IP Camera Series IP Bullet Camera Ref. 1099/400 Bullet Camera IP Varifocal Ref. 1099/401 Dome Camera IP 1099/460 Dome Camera IP Varifocal 1099/461 Vandal Dome IP 1099/462 USER MANUAL...
INTRODUCTION Thank you for purchasing our integrated and developed network camera products for network video monitoring. Our range includes the following products: Storage Network Bullet, Wireless Storage Network Bullet, IR Network Dome, IR Network Weather-Proof and High-Speed Network Ball cameras. Individual high-performance SOC chips are used in the media processor for audio/video capture, compression and transmission/transfer.
PRODUCT DESCRIPTION URMET S.p.A. Ref. 1099/400, Ref. 1099/401, Ref. 1099/460, Ref. 1099/461 and Ref. 1099/462 are PRO Series 5 Megapixel IP cameras che possono essere controllate da connessione di rete TCP/IP. TECHNICAL CHARACTERISTICS ➢ Processor that ensures economic performance. ➢...
WARNINGS Power supply ➢ Before connecting the equipment to the electrical outlet, ensure that the nameplate specifications match those of the mains power supply. ➢ It is advisable to install a suitable disconnection and protection switch upstream from the equipment. ➢...
Page 7
Network configuration ➢ The camera default setting is DHCP mode. If the installation network does not support dynamic addressing (DHCP), the device will automatically switch to the factory-set IP address 192.168.1.168. The Urmet “Device Search Tool” software can be used to change the IP address and other network settings to prevent conflict with other devices on the network.
OVERVIEW RANGE OF APPLICATION These network cameras with their powerful image processing capacity can be used in various public places, such as malls, supermarkets, schools, factories and workshops, as well as in environments requiring HD images, such as banks and traffic control systems, as illustrated in the figure below: Monitoring centre PRODUCT DESCRIPTION An IP camera is an online digital surveillance camera, equipped with a web server and capable of independent operation,...
DEVICE CONNECTION The IP camera can be connected in two ways: • Connection to a PC Connect the IP camera to the PC using a direct network cable, with the power input connected to a 12VDC adaptor, and enter the IP addresses of the PC and the camera in a network segment. The IP camera will communicate with the PC within one minute after being switched on if the network is working properly.
OPERATING INSTRUCTIONS CHECKING THE CONNECTION • The factory default IP address for the IP camera is 192.168.1.168 and the subnet mask is 255.255.255.0. Give your computer an IP address in the same network segment as the IP camera, for example, 192.168.1.69, and the same subnet mask as that of the IP camera.
Note: Device Config Tool uses the Multicast protocol to search for the device across the segments; however, since firewalls prevent multicast data packet traffic, they must be disabled so that the information on the device can be acquired. Online device search procedure Run Device Config Tool by double-clicking on the icon.
LOGIN PREVIEW Open IE and enter the IP address of the camera (http://192.168.1.168) to bring up the login window shown below: Login Interface for H.265 IP Cameras. Figure 1 In the login window you can choose a language for the IE client. Enter your username (admin by default) and password (admin by default) and then press OK.
This reads the recording file from the SD card and plays it back through the browser (if SD card support is provided) : Access to the device settings menu to customise the settings of various parameters. : For snapshot, video file type and storage path settings. : Help information (current user, Web browser and plug-in versions) and logout button for returning to the login page.
Page 14
Opzione Value Explanation Manually adjusts zoom (+ zoom in / - zoom out) Zoom Step/-/+ Step: defines zooming speed Manually adjusts focus (+ increase / - decrease) Focus Step/-/+ Step: defines focusing speed This function is used to customise the camera focusing mode.
LOCAL SETTINGS Select Local Settings to access the following dialogue window: here you can set the video storage location, paths for downloading remote files and storing snapshot images, the file type (RF by default, with H265, AVI, MP4 or BMP encoding), video recording duration and screen capture file type (BMP or JPG).
• (IO) alarms: Motion and Alarms. • Intelligent: see the chapter on intelligent video analysis. :from left to right, Play/Pause, Stop, Advance one frame, (select once to play one frame), Record, Capture, Download, Zoom, Audio control. :from left to right, Zoom, Original proportions, Increase scale, Full screen. 10 REMOTE SETTING 10.1 DISPLAY CONFIGURATION 10.1.1...
10.1.2 IMAGE CONTROL Select Image Control in Display to open the following page: • IR-CUT Mode: Select the integrated IR-CUT filter mode to ensure that the camera functions properly in Day/Night: GPIO Automatic, Coloured, Black-White and Schedule (B/W), for which the time interval must be indicated.
10.1.1 PRIVACY ZONE (ZONA PRIVACY) Select Privacy Zone in Display Configuration to open the following page: Enable Privacy Zone, and then use the right mouse button to trace rectangles around areas not to be displayed during recording, in screenshots and in Live viewing. Save when done to keep the settings. 10.1.2 Select Display to open the following page: DS1099-047A...
ROI setting procedure: Choose a region of application. Press and hold the left mouse button and drag out a ROI (only one ROI can be set for each zone), Select Save to apply the ROI. • Region ID: Up to 8 ROI zones can be set in one bit stream. •...
10.2.2 SCHEDULE Select Schedule in the Record menu to access the following page. Example: a grid on the table represents 30 minutes; green indicates normal recording, yellow a movement detection alarm and red a recording alarm. You can set these parameters, according to your needs, to choose different types or times of recording.
• Type: Network connection mode: DHCP (Automatically Acquired), Static (Manually configured) and PPPOE; DHCP (Automatically Acquired) is the default setting. • Client Port: The port for the clients that connect to the IP camera. • HTTP Port (Porta http): Web port for the IP camera. •...
• Bit Rate: set the Bit rate value in Kbps. • Audio: Enables audio for each bit stream. • I frame interval: Sets the interval of a single frame. 10.3.3 E-MAIL CONFIGURATION Select E-Mail in the Network menu to open the following page for setting up the e-mail service – used with the alarm function to send images to the mail server: •...
10.3.4 DDNS CONFIGURATION Select DDNS in the Network menu to open the following page: DDNS (DDNS): Dynamic DNS configuration – used with the server to access an Extranet network. DDNS (Dynamic DNS) is a service used to record a domain name and floating IP address with the DDNS server so that the domain name can be routed towards the IP address even if it is modified in a dynamic IP system.
10.3.5 IP FILTER Select IP Filter in the Network menu to open the following page: • Filtering mode: Three modes are available (Allow all IP connections, Allow only IP connections which have been set up, Do not Allow the IP connections which have been set up). •...
• RTSPEnable: Enables or excludes RTSP. RTSP is enabled by default. If disabled, it cannot be found with ONVIF. • RTSP Port: The default port number is 554 and it can be changed by setting another value between 1024 and 65535.
10.3.8 HTTPS Allows you to set the security encryption protocol. 10.4 ALARM 10.4.1 MOTION Select Motion in the Alarm menu to open the following page: Motion Detection setting procedure: • Select Enable. • Click and hold the left mouse button and drag out an area for motion detection. •...
• Enable Send Mail, a function used with SMTP to enable the sending of e-mail. • Enable Send Cloud: a function used to send the Motion event to the Cloud. • Select Save to apply the settings. (Note: When any object moves within the target area, a green letter "M" is displayed in the preview frame) 10.4.2 I/O ALARM (DOVE PREVISTO) Select Alarm in the Alarm menu to open the following page:...
10.4.1 LENS BLOCKING Select Lens Blocking in the Alarm menu to open the following page: Select Enable to activate the Sensitivity and Send E-Mail options. • Sensitivity: Set the sensitivity level (level 1~6; the higher the value, the greater the sensitivity level). •...
10.4.1 SOUND DETECTION This function allows you to detect sound in the external environment if IP camera model has an audio microphone connection. • Enable: enable or exclude the Sound Detection function. • Rise: enable or exclude the sound detection Rise function •...
10.5 DEVICE This includes SD Card, Logs and Audio. The various interfaces and functions are described below. 10.5.1 HDD (DOVE PREVISTO) Select HDD in the Device menu to access the following page. Insert the SD card in the device: the system will automatically detect the total capacity and provide information on the remaining recording time.
Audio setup procedure: Select the Enable Audio option to access the audio parameters, then set the audio input/output volume (0~10) and select Save to save the set parameters. (Note: the audio option in Streaming Video must be enabled in order to use the audio function).
10.5.4 CLOUD STORAGE In the event of an alarm, the 5M IP camera is capable of sending images and video to a Cloud storage service via Dropbox, a free service that allows you to easily store and share snapshots and always have them on hand when needed. The setting can be accessed under Cloud in the side menu.
• NTP: Select the Enable NTP option, enter the address of the synchronisation server, choose a time zone and save the settings. The system will correct the time based on the synchronisation server. • Synchronise: The device will use the PC as a synchronisation server to correct the time. 10.6.2 USER CONFIGURATION Select User in the System menu to open the following page:...
10.6.3 INFO (INFORMAZIONI DI SISTEMA) Select Info in the System menu to open the following page: Some system information is displayed in this section, including the device type, MAC address and software version. The QR Code is a P2P ID that can be used by an app. 10.7 ADVANCED This includes Firmware Update, Load Default and Maintain.
LOAD DEFAULT (CARICA DEFAULT) 10.7.1 Select Load Default in the Advanced menu to open the following page: Enable le relative opzioni e selezionare Save (Salva) per ripristinare i parametri predefiniti di fabbrica. 10.7.2 SYSTEM MAINTENANCE Select Maintain in the Advanced menu to open the following page: DS1099-047A...
10.7.3 IMPORT AND EXPORT This function allows you to import and export the IP Camera configuration parameters. 10.8 INTELLIGENT This section briefly describes the intelligent video analysis functions capable of generating specific events that can also be recorded on a remote NVR. For further details on the use and settings of the intelligent video analysis functions, you can visit the URMET website http://www.urmet.com for series or product codes, the availability of relevant additional material and any firmware updates describing improvements to the intelligent video analysis algorithms.
This particular function is set and use only from NVR Menu refer to camera connected and set in record mode. IMPORTANT NOTE: ➢ Face Recognition function can be available only for NVR Pro Series with new GUI 5.2 DS1099-047A...
11 MOBILE SOFTWARE Mobile Software is used for the iOS (iPhone, iPad) and Android platforms (Android Smartphone, Tablet). The following is a description of the Mobile Client Software. 11.1 Smartphone Device 11.1.1 URMET IUVS PLUS MOBILE SOFTWARE Urmet iUVS plus is a TVCC application for iOS and Android on smartphones, pads and tablets that is compatible with all URMET devices, both IPCam (Codec H265) and DVR/NVR/HVR (all codecs).
Getting Started • Download the iUVS app from the Apple Store or Google Play Store and install it. • Connect your iPhone, iPad, Android phone or Android tablet to the Internet via the 3G network or WIFI. • Run the application to access the “Live” menu To access the menu, select the icon at the top left 11.1.1.1...
Page 40
1. Open a device Select to open the device list shown below, then select one of devices in the list: all its channels will open automatically. Opening a channel Selecting a device brings up the list of channels; select a channel, which will be displayed in the main window. Recording a live video stream You can record the stream while viewing a video in live mode.
Page 41
Live video In live mode, selecting allows you to select channels individually or all together. PTZ Control PTZ is short for Pan-Tilt-Zoom and refers to camera movement options. Select to open PTZ mode; this will bring up the PTZ control buttons of the live page. Select the arrows to move it sideways or up and down.
11.1.1.2 Playback Select “Playback” in the main menu; the play list will be displayed A channel from the device can be played remotely 1. Selecting a channel Select the “Remote Playback” button to open the device list, as shown below; select a channel on a device in the list. 2.
When you have selected a channel, all dates with recordings will be marked with a dot. Select a date to play the recordings from that day. 11.1.1.3 Record You can record the stream while viewing a video in live mode, as described previously. 11.1.1.4 Images Images opens a gallery of screenshot pictures.
11.1.1.7 Device Add or delete a device “Device” allows you to add or delete a device and edit its properties. Select Menu and “Device” or the icon at the top right of the start screen to open the interface shown below and manually add a device To add a new device, select “+”, then Manual Adding, Import Device (via QR Code), Online Device (Device present on network): enter the name of the device, the address (IP, domain name or device ID for the DDNS Urmet account), the...
To add a device using automatic network search: Choose the device and select “Add Device” NOTE: the Data Port (i.e. 9000) must be set up in order for the Mobile Software to work properly. If you do not configure the mobile device port, the iUVS Mobile Software will not work. To delete a device from list, select the name of the device you want to delete, then press the delete button next to the device name.
11.2 P2P FUNCTION Once the IP camera has been configured to the network, to remotely display images on an iPhone or Android smartphone, download the URMET iUVS apps from the online stores. For viewing on an Apple iPad or Android tablet, download the iUVSpad app from the Apple Store or the iUVStab app from the Google Play Store.
Page 48
Fill in the “Password” field entering password (default: 00000000), then press “Save” and wait for about 10 seconds for the NVR LIVE video to automatically load. IMPORTANT NOTE: In addition to P2P mode, the IP camera can also be remotely viewed on a smartphone via the Urmet DDNS service.
12 TECHNICAL SPECIFICATIONS FOR THE IP 5M FIXED LENS BULLET AND DOME IP CAMERAS Description Items Starlight Bullet IP Camera Starlight Dome IP Camera 1099/400 1099/460 Image Sensor 1/2.8" Progressive CMOS Sensor Type IMX335 Video Format Optional format P/N Minimum Luminance Colour 0.01lux @ F1.2(AGC ON);...
Page 50
Description Items Starlight Bullet IP Camera Starlight Dome IP Camera 1099/400 1099/460 Mobile Support Software: (iOS, Android) SMART Smart analysis (perimeter intrusion detection, line crossing detection, object detection, capability crossing counter, face detection, person detection, face recognition) TCP/IP, HTTP, DHCP, DNS, DDNS, RTP/RTSP, PPPoE, Protocols SMTP, NTP, UPnP, SNMP, HTTPS, FTP Network...
13 TECHNICAL SPECIFICATIONS FOR THE IP 5M VARIFOCAL BULLET AND DOME IP CAMERAS Description Starlight Bullet IP Starlight Dome IP Starlight Vandal Items Camera Camera Dome IP Camera 1099/401 1099/461 1099/462 Image Sensor 1/2.8" Progressive CMOS Sensor Type IMX335 Video Format Optional format P/N Minimum Luminance Colour 0.01lux @ F1.2 (AGC ON);...
Page 52
Description Starlight Bullet IP Starlight Dome IP Starlight Vandal Items Camera Camera Dome IP Camera 1099/401 1099/461 1099/462 Windows 7 O.S. or higher / MAC O.S. 10.8.0 or higher Mobile Support Software: (iOS, Android) SMART Intelligent Analysis (perimeter intrusion detection, line crossing detection, object detection, crossing capability counter, face detection, person detection, face recognition) TCP/IP, UDP, RTP/RTCP, RTSP, HTTP, SMTP, DNS, DDNS, DHCP, FTP,...
14 MAXIMUM RECORDING TIME WITH SD CARD 14.1 REF. 1099/401 – REF. 1099/461 – REF. 1099/462 The following resolution options can be selected for Main Stream recording: “5M”, “4M”, “3M”, “1080P”, “960P” and “720P” for IP cameras with H.265 codec ➢...
Page 54
1 recording channel with 1080P resolution (1920x 1080) and H.265 Codec Variables to be set Results Results Results Results Results Bitrate Frame rate SD 8GB SD 8GB SD 16GB SD 16GB SD 32GB SD 32GB SD 64GB SD 64GB SD 128GB SD 128GB (Kbps) (fps)
Page 55
1 recording channel with 3Mpx resolution (2048x1520 and 2304x1296) and H.264 Codec Variables to be set Results Results Results Results Results Bitrate Frame rate SD 8GB SD 8GB SD 16GB SD 16GB SD 32GB SD 32GB SD 64GB SD 64GB SD 128GB SD 128GB (Kbps)
15 APPENDIX 15.1 ROUTER PORT FORWARDING To remotely view the IP Camera through the Internet, you must first set the web port and client port of IP Camera. Taking a Cisco router as an example: The IP address of the IP camera is 192.168.1.168, the web port is 8000 and the client port is 9988. DS1099-047A...
15.2 FREQUENTLY ASKED QUESTIONS ◆ Internet Explorer cannot load and install plug-ins. Possible cause: IE security level is set too high. Solution: Set IE security level to the minimum level. ◆ After updating, I cannot access the IP Camera through Internet Explorer. Solution: Clear the IE cache as follows: open IE Tools, select Internet Options, select the 2nd option under “Delete Files”...
Page 60
DS1099-047A Technical area URMET S.p.A. customer service 10154 TORINO (ITALY) 011.23.39.810 VIA BOLOGNA 188/C http://www.urmet.com Tel. +39 011.24.00.000 (AUTO) e-mail: info@urmet.com +39 011.24.00.300 - 323 MADE IN CHINA DS1099-047A...