Filter And Dust Bags - Supreme 150 / Performer 150 / Supreme 250 / Performer 250 / Supreme Lcd; Replacing The Bag Fi Lter; Fitting The Bag Fi Lter; Replacing The Dust Bag - Nilfisk-Advance Supreme 100 EU Instructions For Use Manual

7 Filter and dust bags - Supreme 150 / Performer 150 / Supreme 250 /
Performer 250 / Supreme LCD
7.1 Replacing the bag fi lter
A bag fi lter must always be installed in the dust container.
Clean the fi lter in the following way:
1. Release the two handles clamping the dust container.
The handles are easily unlocked by lifting up the
handles until they come to a stop. When you pull the
handles outwards away from the cleaner, the container
is released. Fig. 22.
2. Do not remove the fi lter from the container. Instead,
give the fi lter a light shaking inside the container to
loosen dust from the fi lter allowing it to fall into the
container. This is done by grasping the strap on the
fi lter and quickly move the fi lter up and down as shown
in Fig. 23.
3. Lift out the bag fi lter. If a dust bag is being used - re-
move the dust bag. Then empty the container of any
remaining dust in a suitable place.

7.3 Replacing the dust bag

The machine is supplied with a dust bag. Replace the dust
bag in the following way:
1. Release the two handles clamped on to the dust con-
tainer. The handles are easily unlocked by lifting up the
handles until they come to a stop. When you pull the
handles outwards away from the cleaner, the container
is released. Fig. 22.
2. Lift off the container.
3. Shake the dust from the bag fi lter. It may be advanta-
geous for the fi lter to be installed in the container in
such a way that dust in the fi lter can be shaken down
into the dust container.
4. Lift out the bag fi lter.
5. Remove the dust bag by taking hold of the cardboard
stiff ener and carefully pulling out the card and bag from
the container, Fig. 24. Fold down the perforated part of
the cardboard towards the opening of the bag in order
to prevent the bag contents to leak out.
6. Empty the container of dust.
Original Instructions
Fig. 22
7.2 Fitting the bag fi lter
Replace the bag fi lter in the machine as follows:
1. Replace the cleaned/shaken bag fi lter in the container.
Make sure the fi lter support fi ts into the inner edge
of the dust container properly. Check that the fi lter is
fi tted the right way up - the cloth handle on the fi lter
should be visible.
2. Then replace the dust container with the bag fi lter in
the cleaner's vacuum unit.
3. Attach the container on the vacuum unit by lifting the
container back in place and pushing the handles back
in over the edge of the cleaner till you hear a click.
Push down the handles and ensure that the vacuum
unit and dust container are fi tted together properly.
Fig. 24

7.4 Fitting the dust bag

Replace the dust bag as follows:
1. Fit the dust bag's card with a hole into the bag holder,
Fig. 25.
2. Replace the cleaned/shaken bag fi lter in the container.
Make sure the fi lter support fi ts into the inner edge of
the dust container properly.
Check that the fi lter is fi tted the right way up - the cloth
handle on the fi lter should be visible.
3. Replace the dust container on the vacuum unit. Close
the container on the vacuum unit by applying inward
pressure to the two handles to ensure the vacuum unit
and dust container are fi tted together properly.
The Supreme 150 / Performer 150 / Supreme 250 /
Performer 250 / Supreme LCD can be run with or with-
out the installation of a dust bag - the choice is yours.
These products must though always be operated with
the bag fi lter fi tted in the cleaner.
Fig. 23
Fig. 25
47