Table of Contents
Advertisement
18
Device Description
Pos : 18.11 /Serie 750 ( WAGO-I/O-SYST EM)/Gerätebeschr eibung (alte Struktur)/Anschl üss e/Lei stungs kontakte/Fel dversorgung - Ü bersc hrift 3 @ 6\mod_1256294692864_21.doc x @ 43664 @ 3 @ 1
3.2.2
Power Jumper Contacts/Field Supply
Pos : 18.12.1 /Serie 750 ( WAGO-I/O- SYST EM)/Wic htig e Erl äuter ung en (alte Struktur)/Sic her heits- und s ons tige Hi nweis e/Vorsicht/Vorsic ht: Verletz ungsgefahr durch sc harfkantige Mess er kontakte! @ 6\mod_1256193279401_21.doc x @ 43414 @ @ 1
Risk of injury due to sharp-edged blade contacts!
The blade contacts are sharp-edged. Handle the I/O module carefully to prevent
injury. Do not touch the blade contacts.
Pos : 18.12.2 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung ( alte Struktur)/Anschl üss e/Leis tungs kontakte 2 LK (Messer /Feder) - Ei nleitung @ 15\mod_1371721641099_21.doc x @ 123714 @ @ 1
The I/O module 750-1515/040-000 has 2 self-cleaning power jumper contacts
that supply and transmit power for the field side. The contacts on the left side of
the I/O module are designed as blade contacts and those on the right side as
spring contacts.
Pos : 18.12.3 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung ( alte Struktur)/Anschl üss e/Leis tungs kontakte 2 LK (Messer /Feder) - Abbil dung (16-Kanal) @ 15\mod_1370866610582_21.doc x @ 122222 @ @ 1
Figure 3: Power Jumper Contacts
Pos : 18.12.4 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung ( alte Struktur)/Anschl üss e/Leis tungs kontakte 2 LK (Messer /Feder) - Legende @ 15\mod_1371721352500_21.doc x @ 123710 @ @ 1
Table 4: Legend for Figure "Power Jumper Contacts"
Contact
1
2
3
4
Pos : 18.12.5 /Serie 750 ( WAGO-I/O- SYST EM)/Wic htig e Erl äuter ung en (alte Struktur)/Sic her heits- und s ons tige Hi nweis e/Ac htung/Ac htung: M axi maler Str om Leistungs kontakte 10 A @ 3\mod_1226499143500_21.doc x @ 25029 @ @ 1
Do not exceed maximum values via power contacts!
The maximum current that can flow through the power jumper contacts is 10 A.
The power jumper contacts can be damaged and the permissible operating
temperature can be exceeded by higher current values.
When configuring the system, do not exceed the permissible maximum current
value. If there is a higher power requirement, you must use an additional supply
module to provide the field voltage.
Pos : 18.13 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.3.0
750-1515/040-000 8DO 24VDC 0.5A 2-Wire XTR
Type
Function
Spring contact Potential transmission (U
Spring contact Potential transmission (0 V) for field supply
Blade contact
Potential feed-in (0 V) for field supply
Blade contact
Potential feed-in (U
WAGO-I/O-SYSTEM 750 XTR
) for field supply
v
) for field supply
v
Advertisement
Table of Contents
