Device Description - WAGO 750-530 Manual

WAGO-I/O-SYSTEM 750
750-530 8DO 24V DC 0.5A
Pos : 19 /All e Seri en (Allgemei ne Module)/Ü berschriften für alle Serien/Gerätebesc hreibung/Gerätebeschr eibung - Übersc hrift 1 @ 3\mod_1233756084656_21.doc x @ 27096 @ 1 @ 1
3

Device Description

Pos : 20.1 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Ei nlei tung/Anwendung/D O/Anwendung 750- x5xx D O @ 3\mod_1233764594468_21.doc x @ 27120 @ @ 1
The 750-530 (8DO 24V DC 0.5A) Digital Output Module transmits binary control
signals from the automation device to the connected actuators (e.g., solenoid
valves, contactors, transmitters, relays or other electrical loads).
Pos : 20.2 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Ei nlei tung/I/O-Besc hrei bung/DO/I/O-Besc hrei bung 750-05xx 8 D O 1-Leiter (DO 1 ... DO 8) @ 4\mod_1235647050031_21.doc x @ 27858 @ @ 1
The module has eight output channels. Eight 1-conductor actuators may be
directly connected to the module. The actuators can be connected using
connection DO 1 ... DO 8.
Pos : 20.3 /Serie 750 (WAGO-I/O-SYST EM)/Wic htige Erläuterungen/Sicherheits- und sonstig e Hinweis e/Hinweis/Hi nweis: D O Potenti al ver vi elfältigungs modul e für Aktor vers orgung ei nsetzen @ 3\mod_1233765481250_21.doc x @ 27140 @ @ 1
Use field side connection modules!
Where required, use the appropriate field side connection modules for power
supply to the actuators.
Pos : 20.4 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Ei nlei tung/I/O-Besc hrei bung/Allgemei n/Ver weis auf Kapitel "Ansc hlüss e" @ 8\mod_1276775378035_21.doc x @ 57956 @ @ 1
The assignment of the connections is described in the "Connectors" section.
Pos : 20.5 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Ei nlei tung/I/O-Besc hrei bung/Allgemei n/Ver weis auf Kapitel "Geräte anschli eß en" > "Ansc hlus sbeis piel(e)" @ 5\mod_1246015203281_21.doc x @ 36298 @ @ 1
Connection examples are shown in section "Connecting Devices" > ... >
"Connection Example(s)".
Pos : 20.6 /Serie 750 (WAGO-I/O-SYST EM)/Wic htige Erläuterungen/Sicherheits- und sonstig e Hinweis e/AchtungAc htung: DO Indukti onsspannungsbegrenz ung El ektr oni k @ 3\mod_1233815757507_21.doc x @ 27153 @ @ 1
Limit all induced voltage!
The electronic components of the I/O module can be damaged by the induced
voltage produced when inductive loads are de-activated.
An appropriate protection circuit, e.g., a recovery diode, must be installed in
parallel to the load to limit this induced voltage.
Pos : 20.7 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Ei nlei tung/I/O-Besc hrei bung/DO/I/O-Besc hrei bung 750- x5xx D O HSS / posi ti vsc haltend (24 V) @ 3\mod_1233816955742_21.doc x @ 27160 @ @ 1
The I/O module outputs provide high-side switching. If the signal status of an
output channel is at "high" the 24 V potential for field power will be switched to
the appropriate output connection.
Pos : 20.8 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Ei nlei tung/I/O-Besc hrei bung/DO/I/O-Besc hrei bung 750-05xx Leistungs kontakt durch Ei nspeis eklemme @ 5\mod_1246856959993_21.doc x @ 36590 @ @ 1
The supply voltage for the field side is derived from an adjacent supply module by
means of power jumper contacts.
Pos : 20.9 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Ei nlei tung/LED-Anz eige/LED Zustand Signal @ 3\mod_1233755258578_21.doc x @ 27087 @ @ 1
A green LED indicates the switched status of each channel.
Pos : 20.10 /Serie 750 ( WAGO-I/O-SYST EM)/Gerätebeschr eibung/Ei nleitung/LED-Anzeig e/Ver weis auf Kapitel " Anzeig eel emente" @ 5\mod_1246010525000_21.doc x @ 36194 @ @ 1
The meaning of the LEDs is described in the "Display Elements" section.
Pos : 20.11 /Serie 750 ( WAGO-I/O-SYST EM)/Gerätebeschr eibung/Ei nleitung/Versorgung/Vers orgung 24 V, 0 V über Leistungs kontakte Standard @ 3\mod_1226498974531_21.doc x @ 25020 @ @ 1
The I/O module 750-530 (8DO 24V DC 0.5A) receives the 24 V voltage supply
for the field level from an upstream I/O module or from the fieldbus
coupler/controller via blade-formed power jumper contacts. It then provides these
potentials to subsequent I/O modules via spring-formed power jumper contacts.
Pos : 20.12 /Serie 750 ( WAGO-I/O-SYST EM)/Wichtig e Erl äuter ung en/Sic her hei ts- und s onstige Hinweise/Ac htung/Ac htung: Maxi maler Str om Leis tungs kontakte 10 A @ 3\mod_1226499143500_21.doc x @ 25029 @ @ 1
Manual
Version 1.2.0
Device Description 13