Carrier PIC 5+ User Manual page 63

Table Name PIC Table Type
QCK_CAL
Menu Name Status
HBP_MAXA
24
25 HBP_MINA
26 DMP_CAL 0 to 1
27 DMP_ST 0 to 2
28
29
30 DMP_MAXA
31 DMP_MINA
Table Name PIC Table Type
MAIISMC
Menu Name Status
cycle_1 no/yes
1
2 ph_loss no/yes
3 ov_volt no/yes
4 un_volt no/yes
5 amp_unb no/yes
6 volt_unb no/yes
7 overload no/yes
8 lratrip no/yes
9 slratrip no/yes
grnd_flt no/yes
10
11 ph_rev no/yes
12 freqflt no/yes
13 ism_por no/yes
14 phase_1 no/yes
15 phase_2 no/yes
16 phase_3 no/yes
17 start_ok no/yes
18 1m_flt no/yes
19 2m_flt no/yes
20 prs_trip no/yes
21 strt_flt no/yes
22 no_amps no/yes
23 accelflt no/yes
24 highamps no/yes
25 stop_ok no/yes
26 1m2mstop no/yes
27 ampstop no/yes
28 hardware no/yes
29 calfc_er no/yes
30 conf_err no/yes
31 un_used no/yes
Table Name PIC Table Type
MAIISMH
Menu Name Status
1 AMPS_H1
2 AMPS_H2
3 AMPS_H3
4 FREQ_H
5 GRFT_H1
6 GRFT_H2
GRFT_H3
7
8 phase_h1
9 phase_h2
10 phase_h3
11 Alm_code
12 sum1ht_h
13 sum2ht_h
14 sum3ht_h
15 VOLT_H1
16 VOLT_H2
Instance HMI Menu Path
12H 6 //MAINMENU/
Default Unit Note Menu text description
mA
mA
0 -
0 -
-
-
mA
mA
Instance HMI Menu Path
12H 7 //MAINMENU/
Default Unit Note Menu text description
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Instance HMI Menu Path
12H 8 //MAINMENU/MAINTAIN/
Default Unit Note Menu text description
AMPS
AMPS
AMPS
Hz
AMPS
AMPS
AMPS
-
-
-
-
%
%
%
Volts
Volts
EC Valve mA 100%
EC Valve mA 0%
Damper Calib Enable
Damper Calib Status
No Calib Or Failure=0,
Progress=1, Completed=2
Damper mA 100%
Damper mA 0%
Single Cycle Dropout
Phase Loss
Over Voltage
Under Voltage
Current Imbalance
Voltage Imbalance
Overload Trip
Locked Rotor Trip
Starter LRA Trip
Ground Fault
Phase Reversal
Frequency Out of Range
ISM Power On Reset
Phase 1 Fault
Phase 2 Fault
Phase 3 Fault
1CR Start Complete
1M Start/Run Fault
2M Start/Run Fault
Pressure Trip Contact
Starter Fault
Motor Amps Not Sensed
Starter Accel Fault
High Motor Amps
1CR Stop Complete
1M/2M Stop Fault
Motor Amps When Stopped
Hardware Failure
Calibration Factor Error
Invalid Configuration
Unused
Line Current Phase 1
Line Current Phase 2
Line Current Phase 3
Line Frequency
Ground Fault Phase 3
Ground Fault Phase 2
Ground Fault Phase 1
Phase 1 Faulted
Phase 2 Faulted
Phase 3 Faulted
VFD Alarm Code
I2T Sum Heat Phase 1
I2T Sum Heat Phase 2
I2T Sum Heat Phase 3
Line Voltage Phase 1
Line Voltage Phase 2
Low High CCN LEN
Limit Limit Force Force
0 1 x
0 2
Low High CCN LEN
Limit Limit Force Force
Low High CCN LEN
Limit Limit Force Force
63