IDEC KW2D Series User Manual page 108

2 Configuration and Functions
■ Password Settings
Download Password: Select this check box to password protect downloading the project to the KW2D Series Smart
Upload Password:
Manage the passwords appropriately so that third parties do not know them. If you forget the download
password, use the Reset RFID Reader to factory settings function in the KW RFID Configurator to reset
the RFID reader. The project saved in the KW2D Series Smart RFID Reader will be deleted and the settings will
be reset to the factory settings. For details, refer to "RFID Reader List Dialog Box" on page 6-19.
■ Tag Read Settings
IC Tag Standard : Select the check boxes of the IC tag standards to read with the KW2D Series Smart RFID Reader.
"ISO/IEC 14443 Type A(MIFARE etc.)", "ISO/IEC 18092 Type F(FeliCa etc.)", "ISO/IEC 15693 Type V"
Lock Mode: Specify the operation after the KW2D Series Smart RFID Reader reads the RFID tag from the
following.
Disable:
Enable (Holding): When you hold an RFID tag for 1.5 seconds or longer, it will be in "Lock mode
Enable (Time):
Reading Distance: Specify the distance at which the KW2D Series Smart RFID Reader can read RFID tags in 8 steps
by sliding the slider or clicking
The RSSI value (0 to 7) of each specified step is displayed to the right of the slider.
The RSSI value indicates the received signal strength, which is the signal strength when the KW2D
Series Smart RFID Reader reads the RFID tag. An RSSI value of 7 (near) means the strongest
signal strength and a value of 0 (far) means the weakest signal strength. The signal strength
becomes smaller the further the distance between the KW2D Series Smart RFID Reader and RFID
tag. For this reason, the KW2D Series Smart RFID Reader controls the distance between the RFID
reader and RFID tag by judging the detection of the RFID tag only when the RSSI value is greater
than or equal to the set RSSI value.
For example, when the RSSI value is 7 (received signal strength: maximum), reading signal
strengths lower than 7 is abandoned.
Reading Time :
Specify the response time to read the RFID tag in 10 steps by sliding the slider or clicking
The time (300 to 3000 ms in increments of 300 ms) of each specified step is displayed to the right
of the slider.
When "Enable(time)" is selected in Lock Mode, the lock operation time starts counting down after an RFID tag
is held on the KW2D Series Smart RFID Reader and then released.
6-12
RFID Reader.
Download Password:
Download Password (Confirm): Enter the same password that you entered in Download
Select this check box to password protect uploading the project from the KW2D Series Smart
RFID Reader.
Upload Password:
Upload Password (Confirm):
It does not enter "lock mode (locking)". If you keep holding an RFID tag, the
"operation mode" and "detection mode" will be repeated.
(locking)", and when you release the RFID tag, the locking operation will be
released.
Hold an RFID tag to enter "lock mode (locking)". The lock operation is released
when the specified time (1 to 28,800 seconds) elapses from the time when the
RFID tag is released. If you hold the same tag again before the specified time
elapses, the lock operation will be released at that point.
KW2D Series Smart RFID Reader User's Manual
Enter the password. The entered characters are masked with *
(asterisks).
The length of the password is 8 to 16 characters. Only single-
byte alphanumeric characters and symbols can be used.
The password can be set only when the Download Password
check box is selected.
Password.
Enter the password. The entered characters are masked with *
(asterisks).
The length of the password is 8 to 16 characters. Only single-
byte alphanumeric characters and symbols can be used.
The password can be set only when the Upload Password
check box is selected.
Enter the same password that you entered in Upload
Password.
/ .
/ .