Troubleshooting; Transport And Storage - Tunturi FitRun 70i User Manual

GB
General Cleaning
Dirt, dust, and pet hair can block air inlets and accumulate on the
running belt� On a monthly basis: vacuum underneath your treadmill
to prevent buildup� Twice a year, you should remove the black motor
hood and vacuum out dirt that may accumulate�
UNPLUG POWER CORD BEFORE THIS TASK�
Belt adjustments
Adjustment must be made from the rear roller� The adjustment bolts
are located at the end of the step rails in the end caps�
- Tighten the rear roller bolts (clockwise) only enough to prevent
slippage at the front roller� Turn both running belt tension
adjustment bolts in increments of 1/4 turn each and inspect for
proper tension by walking on the belt at a low speed, making sure
the belt does not slip� Keep tensioning the bolts until the belt
stops slipping�
- If you feel the belt is tight enough, but it still slips, the problem
may be a loose Motor drive belt under the front cover�
- Do Not Over-tighten
Over tightening will cause belt damage and premature bearing
failure�
Running belt tracking adjustment
The performance of your treadmill is dependent on the frame running
on a reasonably level surface� If the frame is not level, the front and
back roller cannot run parallel, and constant belt adjustment may be
necessary�
The treadmill is designed to keep the running belt reasonably
centered while in use� It is normal for some belts to drift near one
side while the belt is running with no one on it� After a few minutes
of use, the running belt should have a tendency to center itself� If,
during use, the belt continues to move toward one side, adjustments
are necessary�
EXCEPTION:
During rehabilitation where the user is using one leg much stronger
than the other, it might happen that the running belt drifts to one
side� In these cases you should not adjust unless the running belt
does not centre itself during normal condition usage�
To set running belt tracking (fig. F-5)
A 10 mm Allen wrench is provided to adjust the rear roller� Make
tracking adjustments from the left side only� Set belt speed at
approximately 3 to 5 Km/h�
Remember, a small adjustment can make a dramatic difference!
Turn the bolt on the left side clockwise to move the belt to the right�
Counterclockwise to move to the left� Turn this bolt only a 1/4 turn
and wait a few minutes for the belt to adjust itself� Continue to make
1/4 rotation turns until the belt stabilizes in the center of the running
deck�
The belt may require periodic tracking adjustment depending on use
and walking/running characteristics� Some users will affect tracking
differently� Expect to make adjustments as required to center the
tread-belt� Adjustments will become less of a maintenance concern
as the belt is used� Proper belt tracking is an owner responsibility
common with all treadmills�
‼ NOTE
• Damage to the running belt because of incorrect running-belt
adjustments is not covered by the products warranty�

Troubleshooting

Despite continuous quality control, defects and malfunctions caused
by individual components may occur in the equipment� In most cases
it's unnecessary to take the whole device in for repair, as it's usually
sufficient to replace the defective part�
If the equipment does not function properly during use, contact your
Tunturi dealer immediately� Always give the Model and serial number
of your equipment� Please state also the nature of the problem,
conditions of use and purchase date�
If you require spare parts, always give the Model, serial number of
your equipment and the spare part number for the part you need�
The spare part list is at the back of this manual� Use only spare parts
mentioned in the spare part list�
Error codes
If the display shows an error code
(marked with "E"/ "DC" + number), restart the equipment and check
whether the display still shows the error code� If the display still shows
the error code, immediately contact the dealer�
Oil
OIL is not an error code, see "Lubrication"
-- -- -- --
Console will show "-- -- -- --" when safety key is not in (correct)
position during start up�
"-- -- -- --" is not an error code, see "Safety key"

Transport and storage

⚠ WARNING
• Before cleaning and maintenance, remove the mains plug from
the wall socket�
• Carry and move the equipment with at least two persons�
• Make sure that there are no other persons or objects under the
equipment�
• When folding the folding the equipment, make sure that you
hear the equipment lock into position to prevent the equipment
from dropping back down�
⚠ CAUTION
• Before folding the equipment, make sure that the incline is 0%� If
the incline is not 0%, folding will damage the mechanism�
- Move the equipment as shown (fig� F3)� Move the equipment
and carefully put the equipment down� Place the equipment on
a protective base to prevent damage to the floor surface� Move
the equipment carefully over uneven surfaces� Do not move the
equipment upstairs using the wheels, but carry the equipment by
the handlebars�
2 8