ATTO Technology XstreamCORE FC 7550 Installation And Operation Manual page 34

HttpsCertParams (Supported In-Band)
Displays or sets the attributes used to generate the HTTPS
certificate. All attributes are optional. C is Country with a fixed
length of 2 characters. ST is State with a max length of 128
characters. L is Locality with a max length of 128 characters. O is
Organization with a max length of 64 characters. OU is
Organization Unit with a max length of 64 characters. CN is
Common Name with a max length of 64 characters. If the
attribute contains spaces or commas, it must be enclosed in
quotation marks. Changes made to the HTTPS attributes will take
effect on reboot.
set HttpsCertParams [C | ST | L | O | OU | CN] [nn...nn]
get HttpsCertParams
IdentifyController (Supported In-Band)
IdentifyController causes the 'Alert' LED to blink to enable
identification of this system. Disable this option to cancel the
blinking.
set IdentifyController [enabled | disabled]
get IdentifyController
IdentifyLUN (Supported In-Band)
Lights the LED(s) of disk drive(s) associated with one or more FC
LUNs.
IdentifyLUN [LUN] ...
Info (Supported In-Band)
Info displays version numbers and other product information for
key components. Use the optional 'brief' parameter to show a
more concise subset of system information.
Info <brief>
IPAddress (OEM Configurable, Supported In-Band)
IPAddress controls the current IP address of any Ethernet port(s).
If IPDHCP is enabled, then the 'get' command reports the current
IP address assigned by the network DHCP server, followed by the
(DHCP) identifier.
set IPAddress [mp[n] | all] [[xxx.xxx.xxx.xxx] | [[IPv6-compatible
address] <Prefix length>]]
get IPAddress [mp[n] |all]
IPDHCP(OEM Configurable, Supported In-Band)
IPDHCP allows acquisition of an IP address from a network DHCP
server. When this option is disabled, the IP address used will be
specified by the IPAddress CLI command.
set IPDHCP [mp[n]] [enabled | disabled]
get IPDHCP [mp[n] | all]
IPDNSServer (OEM Configurable, Supported In-Band)
Controls the current DNS Server address. If
then this value is automatically detected. If IPDHCPis disabled,
then this value must be manually set (IPv4 only).
set IPDNSServer [xxx.xxx.xxx.xxx]
get IPDNSServer
IPGateway (OEM Configurable, Supported In-Band)
IPGateway controls the current default gateways used by any
Ethernet port(s). If IPDHCP is enabled, the 'get' command reports
the current IP gateway assigned by the network DHCP server.
set IPGateway [mp[n]] [xxx.xxx.xxx.xxx]
get IPGateway [mp[n] |all]
IPSubnetMask (OEM Configurable, Supported In-Band)
IPSubnetMask controls the current subnet masks used by any
Ethernet port(s). If IPDHCP is enabled, the 'get' command reports
the current IP subnet mask assigned by the network DHCP server.
set IPSubnetMask [mp[n]] [xxx.xxx.xxx.xxx]
get IPSubnetMask [mp[n] |all]
IPV6Prefix (OEM Configurable, Supported In-Band)
Controls the current IPv6 prefix (1-128) of any Ethernet port(s).
set IPV6Prefix [mp[n]] [Prefix length]
get IPV6Prefix [mp[n] | all]
IsReserved (Supported In-Band)
IsReserved displays the reservation status of the current services
session/interface.
IsReserved
Licenses
Displays the system's collection of relevant open source licenses.
Licenses
MaxOpTemp (OEM Configurable, Supported In-Band)
Regulates/displays the maximum enclosure temperature alarm
of the XstreamCORE in degrees Celsius. If the temperature of the
XstreamCORE rises above the maximum MaxOpTemp, thermal
control event handling occurs.
set MaxOpTemp [75-90]
get MaxOpTemp
IPDHCP is enabled,