Specifications; 5100, 5100C, 5401, 5400C, 5403 And 5400 Vision System Specifications - Cognex In-Sight 5000 Series Installation Manual

Specifications

The following sections list general specifications for the In-Sight 5000 series vision systems.
5100, 5100C, 5401, 5400C, 5403 and 5400 Vision System
Specifications
Table 3-1: 5100, 5100C, 5401, 5400C, 5403 and 5400 Vision System Specifications
Specification 5100/5110
Minimum In-Sight version 4.4.3
Firmware
Requirement
Job/Program 128MB non-volatile flash memory; unlimited storage via remote network device.
Memory
Image 256MB SDRAM
Processing
Memory
Sensor Type 1/3-inch CCD
Sensor 5.92mm diagonal,
Properties 7.4 x 7.4µm sq. pixels
Maximum 640 x 480
Resolution
1
(pixels)
Electronic 16µs to 1000ms
Shutter Speed
Acquisition Rapid reset, progressive scan, full-frame integration.
Bit Depth 256 grey levels
(8 bits/pixel).
Frames Per 60 full frames per second.
2 3
Second
Lens Type C-mount
Lens Cover Clear plastic with an abrasion-resistant coating on the exterior side.
View Port
Material
Trigger 1 opto-isolated, acquisition trigger input. Remote software commands via Ethernet and RS-232C.
Discrete Inputs None built-in. Additional inputs available using a compatible I/O module. (For more information, refer
I/O Modules on page 4
to
Discrete 2 built-in, high-speed outputs. Additional outputs available using a compatible I/O module. (For more
Outputs information, refer to
Status LEDs Power, Network Status, Network Traffic, 2 user configurable.
1
The number of image sensor rows are configurable and can be set within the In-Sight Explorer software. Decreasing the number of rows will
increase the number of frames per second acquired by the vision system. Refer to the AcquireImage topic in the In-Sight
for more information.
2
For In-Sight 5100/5110, 5100C, 5400C, 5403/5413 and 5400/5410 vision systems, the maximum frames per second is job-dependent, based
on the minimum exposure for a full image frame capture using the dedicated acquisition trigger, and assumes there is no user interface
connection to the vision system.
3
For In-Sight 5401/5411 vision systems, the maximum frames per second are job-dependent and based on an 8ms exposure and a full image
frame capture, using the dedicated acquisition trigger, and assumes there is no user interface connection to the vision system.
5100C 5401/5411
5.952mm
diagonal,
4.65 x 4.65µm
sq. pixels
1024 x 768
32µs to
1000ms
24-bit color. 256 grey levels
(8 bits/pixel).
17 full frames
per second.
.) Unlimited inputs when using an Ethernet I/O system.
I/O Modules on page 4
.) Unlimited outputs when using an Ethernet I/O system.
5400C 5403/5413
1/1.8-inch CCD 1/3-inch CCD
5.92mm 8.8mm
diagonal, diagonal,
7.4 x 7.4µm sq. 4.4 x 4.4µm sq.
pixels pixels
640 x 480 1600 x 1200
16µs to 27µs to
1000ms 1000ms
24-bit color. 256 grey levels (8 bits/pixel).
60 full frames 14 full frames
per second. per second.
5400/5410
5.92mm
diagonal,
7.4 x 7.4µm sq.
pixels
640 x 480
16µs to
1000ms
60 full frames
per second.
®
Explorer Help file
9