Subscribe to Our Youtube Channel
Related Manuals for Cognex CAM-CIC-5000-20G-1
Summary of Contents for Cognex CAM-CIC-5000-20G-1
- Page 1 CAM-CIC-5000-20G-1 CAM-CIC-6MR-18G-1 CAM-CIC-10MR-10G-1 CAM-CIC-12MR-8G-1 GigE Area Scan Industrial Camera User Manual 2023 August 18 V1.1.0...
-
Page 2: Foreword
Foreword Abstract The document briefly describes GigE Area Scan Industrial Camera, including product introduction, networking, basic parameters and applications for quick operation. Symbol Convention The following symbols may appear in this document, and their meanings are as follows： Symbol Description Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. -
Page 3: Important Safety Instructions
Important Safety Instructions Here is the proper use of the product and prevention of dangers as well as loss of property, etc. Be sure to follow the instructions when using. Please do not place or install the device in the location with strong sunlight or near ⚫... -
Page 4: Table Of Contents
Directory Contents Contents Foreword ..........................II Important Safety Instructions ....................III Directory ..........................4 1 Product Overview ....................... 5 1.1 Product Introduction ......................5 1.2 Product Features ......................... 5 1.3 Typical Networking ......................5 1.4 Main Technical Parameters ....................6 1.5 Spectral Curve ........................ -
Page 5: Product Overview
Product Overview Product Introduction GigE area scan camera adopts high-performance sensor chip and realizes real-time non-compressed image data transmission via GigE, which is compatible with any application development tool which meets GigE Vision and GenICam standard. Max transmission rate 1Gb/s can satisfy the requirements of transmission rate in most industrial applications. -
Page 6: Main Technical Parameters
Figure 1-1 Typical Networking Main Technical Parameters Main technical parameters of the GigE Area Scan Industrial Camera are as follow: Sheet 1-1 CAM-CIC-5000-20G-1 Technical Parameters 5MP GigE Mono Area Scan Industrial Camera Sensor Model IMX264 Sensor Type... - Page 7 5MP GigE Mono Area Scan Industrial Camera Certification Power 12V≈3.3W Consumption Storage Temperature ： -30 ℃ ～ +80 ℃ ； Operating Temperature Temperature：-30℃～+50℃ 29mm×29mm×42mm (Not including the lens mount and Dimension the rear case connectors) Weight Certification Conforms to CE, FCC, UL, RoHS, GigE Vision V2.0, GenICam Software GenICam and GigE Vision supported devices Sheet 1-2 CAM-CIC-5000R-14G-1 Technical Parameters...
- Page 8 5MP GigE Mono Area Scan Industrial Camera the rear case connectors) Weight Certification Conforms to CE， FCC， UL， RoHS， GigE Vision V2.0， GenICam Software GenICam and GigE Vision supported devices Sheet 1-3 CAM-CIC-6MR-18G-1 Technical Parameters 6MP GigE Mono Area Scan Industrial Camera Sensor Model IMX178 Sensor Type...
- Page 9 Sheet 1-4 CAM-CIC-10MR-10G-1 Technical Parameters 10MP GigE Mono Area Scan Industrial Camera Sensor Model MT9J003 Sensor Type CMOS Mono/Color Mono Shutter Rolling Resolution 3856×2764 Sensor Pixel Size 1.67×1.67 [μm] Sensor Size 1/2.3" Bit Depth 8/10/12 Frame Rate Dynamic 65dB Range Signal to ＞32dB Noise Ratio...
-
Page 10: Spectral Curve
12MP GigE Mono Area Scan Industrial Camera Resolution 4000 x 3000 Pixel Size 1.85 x 1.85 [μm] Sensor Size 1/1.7" Bit Depth Frame Rate Dynamic 66dB Range ＞38dB Signal to Noise Ratio (SNR) Image Gain 0dB～32dB Exposure Time 16μS～1S Image Format Mono：Mono8/12/12p；... - Page 11 Figure 1-1 IMX264 Mono Spectral Response Figure 1-2 MT9P031 Mono Spectral Response...
- Page 12 Figure 1-3 IMX178 Mono Spectral Response Figure 1-4 MT9J003 Mono Spectral Response...
-
Page 13: Environmental Requirements
Figure 1-2 IMX226 Mono Spectral Response Environmental Requirements The following are the environmental requirements for GigE area scan industrial camera： Temperature and humidity ⚫ Ambient temperature should not exceed 50 ℃ , it is best to work in an air-conditioned environment. Operating cover temperature：0℃～60℃. -
Page 14: Interface Description
Interface Description Product Dimensions The product dimensions are as follows： Figure 2-1 29mm×29mm×42mm（Unit：mm） Figure 2-2 29mm×29mm×42mm（Unit：mm） CAM-CIC-5000-20G-1 CAM-CIC-5000R-14G-1 CAM-CIC-6MR-18G-1 CAM-CIC-10MR-10G-1 CAM-CIC-12MR-8G-1 Figure 2-2 Dimensions of Installation Block This installation block is suitable for both 29mm×29mm×42mm models. -
Page 15: Interface Description
Interface Description The back of the device has two interfaces, the network interface and 6pin power as well as I/O interface, as shown below: Figure 2-3 29mm×29mm×42mm Interface Description Figure 2-4 29mm×29mm×29mm Interface Description 2.2.1 Network Interface Network interface, RJ45 Ethernet port, three-speed Ethernet 10M / 100M / 1000Mbps transmission interface for camera control, data transmission and power supply (POE function). -
Page 16: Electrical Specification
Signal Description GPIO（Non-isolated software can configure input and Line2 output） Line0 Opto-isolated output OPTO_GND Opto-isolated signal ground（ISO_GND） GPIO signal ground（GND） Only 29mm×29mm×29mm GigE Camera has this function. Electrical Specification 2.3.1 Power Supply and Network Port Electrical Specifications Sheet 2-2 Power Supply and Network Port Electrical Specifications Parameter Description Power... - Page 17 Input Voltage Description Note DC 30V Limit voltage: input voltage should not The limit voltage of 29mm×29mm×42mm exceed this limit, otherwise it will cause GigE (produced before Jan.,2017) damage to the device opto-isolated input voltage is DC 25V; I/O input safe operating voltage ranges from I/O input safe operating voltage range DC 0～24V DC 0 to DC 18V.
- Page 18 Figure 2-6 Opto-isolated Output Circuit 2.3.2.3 GPIO Input Sheet 2-5 GPIO Input Voltage Description DC 30V Limit voltage: input voltage should not exceed this limit, otherwise it will cause damage to the device Input safe operating voltage range (the min voltage is DC 3.3V when pulled-up DC 0～5.0V from external) Indicates logical 0...
- Page 19 Figure 2-8 Input Circuit of 5V TTL Logic Level 2.3.2.4 GPIO Output Sheet 2-6 GPIO Output Voltage Description I/O output swing range, 30V is limit voltage which should not be DC 0～30V exceeded, otherwise it will cause damage to the device DC +3.3V～+24V Any voltage within this range can be used to indicates logical 1, it is defined by user...
-
Page 20: Indicator Light Description
Indicator Light Description The indicator light description of the device is shown in Sheet 2-7. Sheet 2-7 Indicator Light Description Status Indicator light status Note Red light quick flashing Device booting. IP is assigned, and the application Blue light slight brightness software API is not connected to the device. -
Page 21: Faq
You can solve problems that you may encounter with following instructions: Application fails to discover the device. Reason analysis： ➢ The camera fails to boot up normally. ➢ Connection of network cable is abnormal. ➢ The camera and the Host PC running the client are not in the same LAN. Solutions：... -
Page 22: Cleaning And Maintenance
Cleaning and Maintenance This chapter mainly introduces cleaning and replacement of color filter. We have installed a fully transparent protective glass for the mono camera with the main purpose of preventing dust from falling on the surface of the image sensor. The color camera is equipped with a low-pass filter that cuts off to the near-infrared band.
Need help?
Do you have a question about the CAM-CIC-5000-20G-1 and is the answer not in the manual?
Questions and answers