List Of Field Settings For Indoor Unit - Daikin REYQ-XA Service Manual

SiUS371901E
1.2

List of Field Settings for Indoor Unit

Mode First
No. Code
(∗2) No.
0 Filter cleaning sign interval
0 (∗11) Filter sign setting
1 Filter type
1 (∗11) Filter cleaning sign interval
10 (20)
2 Thermistor selection
2 (∗11) Remote sensor and remote controller thermistor
3 Filter cleaning sign
Information for intelligent Touch Manager /
5
intelligent Touch Controller
Remote controller thermostat control during
6
group control
7 (∗9) Time for absence area detection
1 Auxiliary electric heater ON temperature: Ton
Auxiliary electric heater ON/OFF temperature:
1
Ton/Toff
2 Auxiliary electric heater OFF temperature: Toff
3 Setting the airflow rate when heating
3 (∗6) Electric heater setting
5 (∗6) Electric heater capacity setting
11 (21)
6 (∗9) Setting the rate of human detection
7 Automatic airflow adjustment
8 (∗9) Compensating the temperature around people
9 (∗9) Compensating the floor temperature
0 Optional output switching
1 External ON/OFF input
2 Thermostat switching
12 (22) 3 (∗8) Airflow setting when heating thermostat is OFF
4 Setting of operation mode to AUTO
5 Auto restart after power failure reset
6 (∗8) Airflow setting when cooling thermostat is OFF
0 Setting of airflow rate
1 Airflow direction setting
2 (∗9) Swing pattern settings
13 (23)
4 Setting of airflow direction adjustment range
5 (∗12) Setting of static pressure selection
6 External static pressure settings
Field Settings and Test Operation
Setting Contents
Ultra long life
filter
Long life filter
Standard
filter
Second Code No.
01
Approx.
10,000
hrs.
Approx.
Light Heavy
2,500
hrs.
Approx.
200 hrs.
Light Heavy
Long life filter Ultra long life filter
Short interval Long interval
Remote controller
thermistor + Suction air
Suction air thermistor only
thermistor
Remote sensor
—
thermistor only
Displayed Not displayed
Refer to page 172 for details.
Not permitted Permitted
30 minutes 60 minutes
Refer to page 173 for details.
Standard Slightly increased
Refer to page 174 for details.
Refer to page 175 for details.
High sensitivity Low sensitivity
Completion of
OFF
airflow adjustment
Priorities given on
Suction air
the suction air
temperature only
temperature
–4°C (–7.2°F) –2°C (–3.6°F)
Refer to page 177 for details.
Refer to page 177 for details.
1°C (1.8°F) 0.5°C (0.9°F)
LL tap Set fan speed
Refer to page 178 for details.
Not equipped Equipped
LL tap Set fan speed
Standard High ceiling 1
F (4 directions) T (3 directions)
All direction
synchronized swing
Draft prevention Standard
Standard High static pressure
Refer to page 180 for details.
Field Settings for Indoor Unit
: Factory setting
02 03
Approx.
5,000
hrs.
Approx.
—
1,250
hrs.
Approx.
100 hrs.
—
—
—
Remote
controller
thermistor only
Remote
controller
thermistor only
—
—
—
Increased
Standard
sensitivity
Start of airflow
adjustment
Standard
0°C (0°F)
—
OFF
—
OFF
High ceiling 2
W
(2 directions)
— Facing swing
Ceiling soiling
prevention
—
04
—
—
—
—
—
—
—
—
—
—
Infrared
presence/floor
sensor
disabled
—
Priorities given
on the floor
temperature
+2°C (+3.6°F)
—
—
—
—
—
—
—
—
—
166