Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Daikin 668898001
Summary of Contents for Daikin 668898001
- Page 1 Operation and Maintenance Manual OM 897-3 Group: WSHP Document PN: 910203510 Date: March 2017 Wireless Temperature Control Use with factory or field installed Daikin WSHP wireless RCN Part No. 668898001 - Programmable Part No. 668898101 - Non-Programmable...
- Page 2 THE MANUFACTURER IS NOT RESPONSIBLE FOR THE ORIGINAL EQUIPMENT MANUFACTURER ANY RADIO OR TV INTERFERENCE CAUSED BY (OEM) MUST ENSURE THAT FCC LABELING UNAUTHORIZED MODIFICATIONS TO THIS REQUIREMENTS ARE MET. THIS INCLUDES A EQUIPMENT. SUCH MODIFICATIONS COULD VOID CLEARLY VISIBLE LABEL ON THE OUTSIDE OF THE USER’S AUTHORITY TO OPERATE THE THE FINAL PRODUCT ENCLOSURE THAT DIS- EQUIPMENT.
-
Page 3: Table Of Contents
Backlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Programmable Thermostat Only (668898001) ..7 Setting The Clock . -
Page 4: Introduction
Introduction Figure 1: T9000 Programmable – Front View The T9000 Wireless Temperature Control is a two-part wireless thermostat system designed to provide preci- sion temperature control without the installation labor and expense of wiring. Powered by AA batteries, the thermostat can operate continuously for approximately 18 months, and can be mounted in any suitable location that will provide good temperature control. -
Page 5: Mounting
Figure 2: Opening Thermostat Note: Do not mix old and new batteries. When batteries are changed, replace them all at the same time Programmed data for heating, cooling and time of day will be lost when batteries are completely removed or depleted and will have to be re-entered along with resetting the clock. -
Page 6: Buttons
• Program set up button* • Run – Sets program or manual mode of operation* • Clock set up button* Programmable Thermostat Only (668898001) OM 897-3 www.DaikinApplied.com... -
Page 7: Backlight
Step 2 Backlight The minute digits will now be blinking. Press the UP or Programmable Thermostat Only (668898001) DOWN button to change to the desired minute. When the correct minute is flashing press HEAT/COOL. A single button on the right hand side of the thermostat acti- vates the display backlight. - Page 8 Step 1 Table 1: Weekday Default Program Times and Temperatures Press the PROGRAM button to put the thermostat into the Period Time Heat Cool programming mode. The display will blink all the days of the Morning 6:00 AM 70° 75° week icons.
-
Page 9: Navigating
Set point temperature, indicating the Program / Manual Operation thermostat is holding that temperature. Programmable Thermostat Only (668898001) In manual mode, you can adjust the desired temperature The RUN button toggles the thermostat between manual using the UP and DOWN buttons, and the thermostat will operating mode and program operating mode. -
Page 10: Changing Temperature While Running
RCN if the thermostat batteries are removed, Program or after a power outage. Programmable Thermostat Only (668898001) Installing Nodes You can always change the temperature up or down while If multiple installation teams are installing and linking ther- a program is running. - Page 11 Step 1 Step 2 Press the SW4-INSTALL. button inside the thermostat. The The UP button on the front of the thermostat is used to tog- display will change to the Install Session screen shown in gle between the following two choices: Figure 8, with the “install”...
- Page 12 Step 4 Model 122 - 24VAC Node – Apply power or press PB3, see The control node can be installed to a thermostat as a HEAT Figure 10 on page 13 only, COOL only or HEAT & COOL node. After selecting the When the SW9-LINK button is pressed, the thermostat will node number, the HEAT and/or COOL icon will flash in the display a “Please Wait”...
-
Page 13: Installing Multiple Nodes To A Thermostat
If another node is to be installed to this thermostat, press Figure 10: Wireless Control Node the HEAT/COOL button again. The “Install” icon will flash. As was done previously, press the HEAT/COOL button (Step Two). The node number will begin blinking, select the node number by one using the UP button and continue with the 916.5 MHz Transceiver... -
Page 14: Un-Installing Nodes
Un-Installing Nodes Step 2 Press and hold the PB1-NETWORK button (see Figure 8 on Un-installing nodes, the procedure to remove will un-install page 11) on the inside of the thermostat board for approxi- all nodes at once. mately two seconds. Step 1 No response is displayed. -
Page 15: Om 897-3
“What do I do if the antenna symbol is no longer dis- “When my AC turns off, I can’t immediately make it run again?” played?” This is normal. What you are experiencing is called an anti Ensure the RCN has power. Make sure the thermostat and short-cycle delay. - Page 16 “The display on my thermostat is blank . What happened?” During the cooling season, consider humidity as well as room temperature. When your air conditioner runs, it not only A blank display indicates your batteries are depleted. When cools the air, it also removes moisture, lowering humidity. the low battery icon comes on there is approximately one High humidity can encourage mold growth.
- Page 17 Figure 12: T9000 Programmable Overview - (PN 668898001) www.DaikinApplied.com OM 897-3...
- Page 18 Figure 13: T9000 Non-Programmable Overview - (PN 668898101) OM 897-3 www.DaikinApplied.com...
- Page 20 Daikin Applied Training and Development Now that you have made an investment in modern, efficient Daikin equipment, its care should be a high priority. For training information on all Daikin HVAC products, please visit us at www.DaikinApplied.com and click on Training, or call 540-248-9646 and ask for the Training Department.