Table of Contents
Advertisement
Quick Links
JaNets JT Simple
Instruction Manual for the setup and change
of the line
Congratulations on your purchase of a JUKI product.
To ensure safe use of the JaNets JT Simple, it is necessary to read this Instruction
Manual carefully and fully understand its contents before putting the JaNets JT
Simple into use. Keep this Instruction Manual at a prescribed position to make it
available whenever necessary.
Revision No.
Advertisement
Table of Contents
Related Manuals for JUKI JaNets JT Simple
Summary of Contents for JUKI JaNets JT Simple
- Page 1 Congratulations on your purchase of a JUKI product. To ensure safe use of the JaNets JT Simple, it is necessary to read this Instruction Manual carefully and fully understand its contents before putting the JaNets JT Simple into use. Keep this Instruction Manual at a prescribed position to make it available whenever necessary.
-
Page 2: Table Of Contents
CONTENTS Introduction ..................... 1 I. Prior arrangement ..................1 1. List of layout of terminals ................. 1 2. Login to the report system ............... 2 3. User registration ..................3 3-1. Adding a user ..................3 3-2. Editing the user ................. 5 II. - Page 3 6-4. Changing the order of the machine ..........27 7. Linking up the machine to the terminal ..........28 8. Setting the threshold for smileys ............30...
-
Page 4: Introduction
This Instruction Manual describes the setup and operating procedure of the JUKI JaNets JT Simple when it is put into use. If you have not yet installed the operating environment for the JaNets JT Simple on the relevant personal computers (PCs), install it referring to the Installation Manual. -
Page 5: Login To The Report System
JaNets JT Simple Instruction Manual for the setup and change of the line 2. Login to the report system Start up the report system in accordance with the Installation Manual. * Refer to V.7 Setting the report system in the Installation Manual. -
Page 6: User Registration
JaNets JT Simple Instruction Manual for the setup and change of the line 3. User registration This clause describes the user registration procedure. After you have registered a new user with the report system, the added user is allowed to log in to the report system. - Page 7 JaNets JT Simple Instruction Manual for the setup and change of the line The user information setting screen is displayed. Enter the following information and press the OK button … ③ to confirm the data you have entered. ③ Employee number, name and login name ...
-
Page 8: Editing The User
JaNets JT Simple Instruction Manual for the setup and change of the line 3-2. Editing the user Log in to the report system using the name of user who has administrative rights (user type: adminRole). Then, press the System configuration tab … ○ 1 . - Page 9 JaNets JT Simple Instruction Manual for the setup and change of the line Deleting the user Log in to the System using the name of user who has administrative rights (user type: adminRole). Then, press the System configuration tab …①.
-
Page 10: System Setup
JaNets JT Simple Instruction Manual for the setup and change of the line II. System setup This section describes the setting items that are necessary to view various charts such as the operation rate and quantity of output on the report center. -
Page 11: Factory Setting
JaNets JT Simple Instruction Manual for the setup and change of the line 2. Factory setting 2-1. Adding a plant Select the Basic configuration > Factory … ①. Press the +Add button … ②. ② ① The factory name input dialog is displayed. Edit the Factory name … ③. -
Page 12: Deleting The Factory
JaNets JT Simple Instruction Manual for the setup and change of the line 2-2. Deleting the factory Select the Basic configuration > Factory … ①. Select the factory you want to delete, and press the Edit button … ②. ②... -
Page 13: Deleting The Factory
JaNets JT Simple Instruction Manual for the setup and change of the line 2-3. Deleting the factory Select the Basic configuration > Factory …①. Select the factory you want to delete, and press the Delete button … ②. ② ①... -
Page 14: Floor Setting
JaNets JT Simple Instruction Manual for the setup and change of the line 3. Floor setting 3-1. Adding a floor Select the Basic configuration > Floor … ① and press the +Add button … ②. ② ① The floor name input dialog is displayed. Enter a Floor name … ③ and select the Factory …... -
Page 15: Editing The Floor
JaNets JT Simple Instruction Manual for the setup and change of the line 3-2. Editing the floor Select the Basic configuration > Floor … ①. Press the Edit button … ②. ② ① The factory name input dialog is displayed. Edit the Floor name … ③ and the Factory name …... -
Page 16: Deleting The Floor
JaNets JT Simple Instruction Manual for the setup and change of the line 3-3. Deleting the floor Select the Basic configuration > Floor … ① and press the Delete button … ②. ② ① The floor deletion confirmation message is displayed. -
Page 17: Shift Setting
JaNets JT Simple Instruction Manual for the setup and change of the line 4. Shift setting 4-1. Adding a shift Select the Basic configuration > Shift … ○ 1 and press the +Add button …②. ② ① The shift name input dialog is displayed. Enter a Shift number … ③, Finishing time …... -
Page 18: Editing The Shift
JaNets JT Simple Instruction Manual for the setup and change of the line 4-2. Editing the shift Select the Basic configuration > Shift … ① and press the Edit button …②. ① ② The shift name input dialog is displayed. Edit the Shift number … ③, Finishing time …... -
Page 19: Deleting The Shift
JaNets JT Simple Instruction Manual for the setup and change of the line 4-3. Deleting the shift Select the Basic configuration > Shift … ① and press the Delete button … ②. ① ② The shift deletion confirmation message is displayed. -
Page 20: Line Setting
JaNets JT Simple Instruction Manual for the setup and change of the line 5. Line setting 5-1. Adding a line Select the Basic configuration > Line … ① and press the +Add button … ②. ② ① The line setting screen is displayed. Enter a Line name … ③, Line number … ④, Floor …... - Page 21 JaNets JT Simple Instruction Manual for the setup and change of the line Caution) If you press the "Save" button … ⑧ without entering data on ③ to ⑤, the message shown at the left will be displayed and the line cannot be added.
-
Page 22: Editing The Line
JaNets JT Simple Instruction Manual for the setup and change of the line 5-2. Editing the line Select the Basic configuration > Line … ① and press the Edit button … ②. ② ① The line setting screen is displayed. Enter the Line name … ③, Floor … ⑤, Shift …... - Page 23 JaNets JT Simple Instruction Manual for the setup and change of the line After you have pressed the Save button … ⑧, the screen returns to the previous screen. Then, press the Update button … ⑨. The information on the Edited line … ⑩ is reflected.
-
Page 24: Deleting The Line
JaNets JT Simple Instruction Manual for the setup and change of the line 5-3. Deleting the line Select the Basic configuration > Line … ① and press the Delete button … ②. ② ① The line deletion confirmation message is displayed. -
Page 25: Stopping The Line
JaNets JT Simple Instruction Manual for the setup and change of the line 5-4. Stopping the line Select the Basic configuration > Line … ① and press the Enable button … ②. ② ① The Enable button is grayed out to bring the line to the stop state. -
Page 26: Machine Setting
JaNets JT Simple Instruction Manual for the setup and change of the line 6. Machine setting 6-1. Adding a machine Select the Basic configuration > Line …① and press the +Add button … ②. ② ① List of machines registered with the line … ③ is displayed. - Page 27 JaNets JT Simple Instruction Manual for the setup and change of the line The machine information setting dialog is displayed to allow you to enter the items listed below. ⑤ Machine name * As many as 20 half-width characters or 10 full-width characters can be entered.
-
Page 28: Editing The Machine
JaNets JT Simple Instruction Manual for the setup and change of the line 6-2. Editing the machine Select the Basic configuration > Line … ① and press the Edit button … ②. ② ① List of machines registered with the line … ③ is displayed. -
Page 29: Deleting The Machine
JaNets JT Simple Instruction Manual for the setup and change of the line The machine setting dialog is displayed to allow you to edit the items shown in Table 6-1. ⑤ ⑥ ⑦ ｖ ⑧ ⑩ ⑨ ⑪ After you have completed editing, confirm the data with the Save button …⑪. - Page 30 JaNets JT Simple Instruction Manual for the setup and change of the line 6-4. Changing the order of the machine Put a checkmark to the Checkbox … ① of the machine you want to change the order from the machine list.
- Page 31 JaNets JT Simple Instruction Manual for the setup and change of the line 7. Linking up the machine to the terminal This clause describes how to link up the machines registered with the system (report system) under the Factory > Floor > Line to the terminals.
- Page 32 JaNets JT Simple Instruction Manual for the setup and change of the line Firstly, find and record the Machine number from the machine information setting dialog. (Refer to II-6. Machine setting.) * In order to input the machine number in the terminal, it is recommended to create a line configuration list that contains the lines in the factory in advance and a list of machines of each line.
- Page 33 JaNets JT Simple Instruction Manual for the setup and change of the line 8. Setting the threshold for smileys Select the Basic configuration > Smiley setting … ① and press the Edit button … ②. Then, the Thresholds for change … ⑤ to ⑩ for the smileys can be set.
Need help?
Do you have a question about the JaNets JT Simple and is the answer not in the manual?
Questions and answers