Sony STR-DN1010 Service Manual page 67
Multi channel av receiver
Hide thumbs
Also See for STR-DN1010:
- Operating instructions manual (136 pages) ,
- Quick setup manual (2 pages) ,
- Specifications (2 pages)
Table of Contents
Advertisement
DIGITAL VIDEO BOARD (4/5) IC3202 ABT1015LQ128 (VIDEO DEINTERLACING)
Pin No.
Pin Name
1
RED[0]
2
RED[1]
3
RED[2]
4
RED[3]
5
PPL_VSS
6
PPL-VDD
7
SYSCLK
8
IO_VDD
9
IO_VSS
10
RED[9]
11
RED[10]
12
Core_VDD
13
Core_VSS
14
RED[11]
15
BLUE[0]
16
BLUE[1]
17
BLUE[2]
18
BLUE[3]
19
BLUE[4]
20
BLUE[5]
21
BLUE[6]
22
BLUE[7]
23
BLUE[8]
24
BLUE[9]
25
BLUE[10]
26
BLUE[11]
27
Core_VDD
28
Core_VSS
29
IO_VDD
30
IO_VSS
31
HSN
32
VSN
33
IO_VDD
34
IO_VSS
35
DE
36
GREEN[0]
37
GREEN[1]
38
GREEN[2]
39
GREEN[3]
40
GREEN[4]
41
Core_VDD
42
Core_VSS
43
GREEN[5]
44
IO_VDD
45
IO_VSS
46
GREEN[6]
47
GREEN[7]
I/O
O
Output red video data, not used
O
Output red video data, not used
O
Output red video data, not used
O
Output red video data, not used
-
PLL ground
-
PLL power supply (+1.8V)
I
System clock input - 27MHz
-
I/O Power supply (+3.3V)
-
I/O ground
O
Output red video data, not used
O
Output red video data, not used
-
Core power supply (+1.8V)
-
Core ground
O
Output red video data, not used
O
Output blue video data, not used
O
Output blue video data, not used
O
Output blue video data, not used
O
Output blue video data, not used
O
Output blue video data, C[0]
O
Output blue video data, C[1]
O
Output blue video data, C[2]
O
Output blue video data, C[3]
O
Output blue video data, C[4]
O
Output blue video data, C[5]
O
Output blue video data, C[6]
O
Output blue video data, C[7]
-
Core power supply (+1.8V)
-
Core ground
-
I/O Power supply (+3.3V)
-
I/O ground
Output Hsync/also CSyncN. The state of this pin is latched during hardware reset-
Pull-Down - I2c device addr is 0x30
I/O
Pull-up - I2C device addr is 0x32
Input only used during reset
Output Vsync.
The state of this pin is latched during hardware reset-
I/O
Pull-down - Use ABT1015's internal PLL
Pull-up - Use external PLL to drive video output clock
Input only used during reset, function reserved
-
I/O Power supply (+3.3V)
-
I/O ground
Output Data Enable.
The state of this pin is latched during hardware reset-
I/O
- scaler VTG will start immediately after hardware reset
Pull-up - scaler VTG will be held in reset until released by software {reg. 0x848)
Input only used during reset.
O
Output green video data, not used
O
Output green video data, not used
O
Output green video data, not used
O
Output green video data, not used
O
Output green video data, Y[0]
-
Core power supply (+1.8V)
-
Core ground
O
Output green video data, Y[1]
-
I/O Power supply (+3.3V)
-
I/O ground
O
Output green video data, Y[2]
O
Output green video data, Y[3]
Description
STR-DN1010
67
- Quick Links:
- Digital Board
Hide quick links:
Advertisement
Table of Contents
