Axg1A Remote Transmitter; Axfa11 Remote Transmitter - YOKOGAWA ADMAG TI Series User Manual

● Setting of Write Protect Switch
The write protect function is to prevent the overwriting of
parameters.
Write protection can be carried out using either the write
protection switch (SW1-2) (See Figure 6.3.1) or software
function with parameter setting. If either of these items is
activated, the overwriting of parameters will be prohibited.
Table 6.3.1 Write protect switch (SW1-2)
Position of
Switch
1 2
H ON Write protect: ON
L OFF
Parameters cannot be overwritten
SW1
1 2
H ON
Write protect: OFF
L OFF
Parameter can be overwritten.
SW1
NOTE
• If the hardware switch is set to "ON", the condition
of preventing parameter overwriting kept until the
switch is set to "OFF".
• For the software write protect, read the user's
manual of applicable communication type as listed
in Table 1.1.
● Setting of Address Switch (ADDRESS)
The device IP address can be set using either the
address switch (ADDRESS) (See Figure 6.3.2) or
software parameters.
The Address Switch (ADDRESS) is used to set the 4
octet (8 bits) of the IP address. The 1
of the IP address are set by software parameters. The
4 octet of the address which is set by this switch
th
(ADDRESS) is enabled when the Enable hardware
switch (SW3-1) is set to ON. When the Enable hardware
switch (SW3-1) is set to OFF, the 4
address set by this switch (ADDRESS) is disabled, and
the 4th octet of the address set by software parameter is
enabled.
Table 6.3.2 Address switch
Position of Switch
7 6 5 4 3 2 1 0
Setting range: 1 to 244
1
If all switches are set to "OFF" or "ON",
0 the device IP address (4th octet) is
ADDRESS automatically converted to 210.
Setting example:
If only the address switch "position 7" is set to 1, the
device IP address (4 octet) is 128.
th
(1 * 2 +0 * 2 + 0 * 2 + 0 * 2
7 6 5
* 2 )
0
Description
th
, 2 and 3 octets
st nd rd
octet of the IP
th
Description
+ 0 * 2 + 0 * 2 + 0 * 2 + 0
4 3 2 1
<6. Operation>
● Setting Enable Hardware Address Switch
(SW3-1)
This switch is used to enable or disable the Address
Switch (ADDRESS) and DHCP Switch (SW3-2).
Table 6.3.3 Enable hardware address switch (SW3-1)
Position of
Switch
1 2
Hardware address switch: ON
ON
OFF
Device IP address is set by Address switch.
SW3
1 2
Hardware address switch: OFF
ON
OFF
Device IP address is set by software parameters.
SW3
● Setting DHCP Switch (SW3-2)
The DHCP switch (See Figure 6.3.4) is used to enable or
disable DHCP function. The DHCP function is enabled
or disabled by this switch when Enable hardware switch
(SW3-1) is set to ON. When the Enable hardware
switch (SW3-1) is set to OFF, the setting by this switch
is disabled and DHCP function is enabled or disabled by
software parameter.
Table 6.3.4 DHCP switch (SW3-2)
Position of
Switch
1 2
DHCP function is disabled.
ON
The fixed IP address set by the address switch or
OFF
software parameter is used as the device address.
SW3
1 2
DHCP function is enabled.
ON
OFF
The device IP address is set by DHCP.
SW3

6.3.2 AXG1A Remote Transmitter

(Not applicable for EtherNet/IP communication type.
Please read the descriptions on IM 01E22A01-01EN if
necessary.)

6.3.3 AXFA11 Remote Transmitter

(Not applicable for EtherNet/IP communication type.
Please read the descriptions on IM 01E22A01-01EN if
necessary.)
13
Description
Description
IM 01E21A01-03EN-A