Parameters Related To Cc-Link Ie Tsn - Mitsubishi Electric FR-E800 Instruction Manual (Communication

2.5.4

Parameters related to CC-Link IE TSN

The following parameters are used for CC-Link IE TSN communication. Set the parameters as required.
Pr. Name
541 Frequency command sign
N100 selection
544
CC-Link extended setting
*1
N103
1426
Link speed and duplex mode
*1
selection
N641
1442
IP filter address 1 (Ethernet)
*1
N660
1443
IP filter address 2 (Ethernet)
*1
N661
1444
IP filter address 3 (Ethernet)
*1
N662
1445
IP filter address 4 (Ethernet)
*1
N663
1446
IP filter address 2 range
*1
specification (Ethernet)
N664
1447
IP filter address 3 range
*1
specification (Ethernet)
N665
1448
IP filter address 4 range
*1
specification (Ethernet)
N666
1320 to
User Defined Cyclic
1329
Communication Input 1 to 10
N810 to
Mapping
*1
N819
1330 to
User Defined Cyclic
1343
Communication Output 1 to 14
N850 to
Mapping
*1
N863
804 Torque command source
D400 selection
810 Torque limit input method
H700 selection
*1 The setting is applied after an inverter reset or next power-ON.
*2 The setting is available only for the FR-E800-EPB and the FR-E800-SCEPB.
 Precautions for CC-Link IE TSN communication
• For CC-Link IE TSN, do not change initial values of Pr.1449 to Pr.1454 used to specify the Ethernet IP address range for
command source selection as the IP address is not used. Setting a value other than the initial value in any of the above
parameters may cause an Ethernet communication fault (E.EHR). If the fault occurs, reset the setting of the relevant
parameter to the initial value, or set "9999" in Pr.1432 Ethernet communication check time interval.
 CC-Link extended setting (Pr.544)
• Use this parameter to select the function of the remote registers for the CC-Link IE TSN.
Pr.544 setting
0 (initial value), 1, 12, 14, 18
38
100, 112, 114, 118
138
*1 Refer to the PLC Function Programming Manual.
Initial value Setting range
0
0
1
0, 1, 12, 14, 18, 38,
0 100, 112, 114, 118,
138
0 0 to 4
0
0
0 to 255
0
0
9999
9999 0 to 255, 9999
9999
*2
5 , 100
13787, 20488,
9999
20489
9999
*2
6 , 101
13787, 16384 to
16483, 20488,
9999
20489, 20981 to
20990
9999
0 0, 1, 3 to 6
0 0 to 2
Compatible with the octuple setting of CC-Link Ver.2
Compatible with the octuple setting of CC-Link Ver.2, user defined cyclic
communication data selected
Compatible with the octuple setting of CC-Link Ver.2
Compatible with the octuple setting of CC-Link Ver.2,
user defined cyclic communication data selected
Signed frequency command value
Unsigned frequency command value
Use this parameter to extend the function of the remote
registers for the CC-Link IE TSN.
Set the communication speed and the communication
mode (full-duplex/half-duplex).
Set the range of connectable IP addresses for the
network devices. (When Pr.1442 to Pr.1445 = "0 (initial
value)", the function is invalid.)
Set the index number for inverter parameters and
*2
, 12288 to
inverter control parameters. Functions can be assigned
to remote registers RWwn+4 to RWwn+17 when Pr.544
= "38".
Function disabled
*2
, 12288 to
Set the index number for inverter parameters, monitor
data, and inverter control parameters. Functions can be
assigned to remote registers RWrn+4 to RWrn+1F when
Pr.544 = "38".
Function disabled
In the torque control mode, the torque command source
can be selected.
The torque limit input method can be selected.
Description
PLC function
Description
*1
2. Ethernet Communication
2.5 CC-Link IE TSN
1
2
3
4
5
6
7
8
9
10
27