Super Filter; Filter+Drive; Auto Wah; Saturator - Roland TM-6 PRO Data List

Parameter Value
Character 1–6
EQ Low Freq 200–400Hz
EQ Low Gain -15–+15dB
EQ High Freq 2000–8000Hz
EQ High Gain -15–+15dB
Level
0–127

SUPER FILTER

This is a filter with an extremely sharp slope. The cutoff frequency
can be varied cyclically
Parameter Value
Filter type
Frequency range that will pass through each filter
LPF
Filter Type
BPF
HPF
NOTCH
Amount of attenuation per octave
-12 dB
Filter Slope
-24 dB
-36 dB
Filter Cutoff(#) 0–127
Filter Resonance 0–100
Filter Gain 0–+12 dB
Modulation Sw
OFF, ON
How the cutoff frequency will be modulated
TRI
SQR
SIN
Modulation Wave SAW1
SAW2
SAW1
Tempo Sync OFF, ON
0.05–10.00Hz,
Rate
note
Depth 0–127
Attack 0–127
Level 0–127
Explanation
Type of reverb
Center frequency of the low region
Gain of the low range
Center frequency of the high region
Gain of the high range
Output level
Explanation
Frequencies below the cutoff
Frequencies in the region of the
cutoff
Frequencies above the cutoff
Frequencies other than the region of
the cutoff
Gentle
Steep
Extremely steep
Cutoff frequency of the filter
Increasing this value will raise the
cutoff frequency.
Filter resonance level
Increasing this value will emphasize
the region near the cutoff frequency.
Amount of boost for the filter output
On/off switch for cyclic change
Triangle wave
Square wave
Sine wave
Sawtooth wave (upward)
Sawtooth wave (downward)
SAW2
Specifies whether the modulation
rate is specified as a note value (ON)
or not (OFF).
Rate of modulation
Depth of modulation
Speed at which the cutoff frequency
will change
This is effective if Modulation Wave is
SQR, SAW1, or SAW2.
Output level

FILTER+DRIVE

This is a low-pass filter equipped with overdrive. It cuts the upper
range and adds distortion.
Parameter Value
Cutoff
0–127
Frequency(#)
Filter
0–127
Resonance(#)
Drive
0–127
Level 0–127

AUTO WAH

Cyclically controls a filter to create cyclic change in timbre.
Parameter Value
Filter Type LPF, BPF
Manual
0–127
Peak 0–127
Sens 0–127
Polarity UP, DOWN
Tempo Sync OFF, ON
0.05–10.00Hz,
Rate(#)
note
Depth
0–127
Phase
0–180deg
Low Gain -15–+15dB
High Gain -15–+15dB
Level 0–127

SATURATOR

A saturator which distorts the sound is connected in parallel with
a compressor, producing a rougher tonal character and boosting
the loudness. This also cuts the low-frequency region of the input
audio.
Parameter Value
Saturator Gain 0–127
Saturator Drive 0–127
Saturator Level(#) 0–127
Comp Depth 0–127
Comp Level 0–127
Hi Gain
-12–+6dB
Level 0–127

OVERDRIVE

This is an overdrive that provides heavy distortion.
Parameter Value
Drive(#) 0–127
TRIGGER SETUP
Explanation
Cutoff frequency of the filter
Increasing this value will raise the
cutoff frequency.
Filter resonance level
Increasing this value will emphasize
the region near the cutoff frequency.
Amount of distortion
Output level
Explanation
Type of filter
LPF:
The wah effect will be applied
over a wide frequency range.
BPF:
The wah effect will be applied
over a narrow frequency range.
Adjusts the center frequency at
which the effect is applied.
Width of the frequency region at
which the wah effect is applied
Increasing this value will make the
frequency region narrower.
Adjusts the sensitivity with which the
filter is controlled.
Direction in which the filter will move
UP: Move toward a higher frequency
DOWN:
Move toward a lower
frequency
Specifies whether the modulation
rate is specified as a note value (ON)
or not (OFF).
Frequency of modulation
Depth of modulation
Adjusts the degree of phase shift of
the left and right sounds when the
wah effect is applied.
Gain of the low range
Gain of the high range
Output level
Explanation
Input volume to the saturator
Degree of distortion
Output volume of the saturator
Amount of compression
Output volume of the compressor
Gain of the high range
Output level
Explanation
Degree of distortion
Also changes the volume.
29