ABB DCS800 Series Installation Manual page 51

Unit type
DC I [A-]
800 V
DCS800-A0x-1900-08-D 1900
DCS800-A0x-2500-08-D 2500
DCS800-A0x-3000-08-D 3000
DCS800-A0x-3300-08-D 3300
DCS800-A0x-4000-08-D 4000
DCS800-A0x-4800-08-D 4700
DCS800-A0x-6600-08PD 6200
DCS800-A0x-8000-08PD 7600
DCS800-A0x-9600-08PD 9000
990 V
DCS800-A0x-2050-10-D 2050
DCS800-A0x-2600-10-D 2600
DCS800-A0x-3300-10-D 3300
DCS800-A0x-4000-10-D 4000
DCS800-A0x-5200-10PD 4900
DCS800-A0x-6600-10PD 6200
DCS800-A0x-8000-10PD 7600
1190 V
DCS800-A0x-2600-12-D 2600
DCS800-A0x-3300-12-D 3300
DCS800-A0x-4000-12-D 3800
(1*) Recommendation by ABB:
- Use cable type VPE (90°C; 194°F) with 4 cores
- AC - connection: U, V, W and PE
- DC - connection: L+, L- and 2 * PE
- Ambient temperature: 40°C; 104°F
- Load: 100 %
Recommended cross-sectional areas - tightening torques DC-connection
You will find instructions on how to calculate the PE conductor's cross-sectional
area in VDE 0100 or in equivalent national standards. We remind you that power
converters may have a current-limiting effect.
DC - connection (U+, U-) + 2 * PE
With DC - fuses
Amount of single Amount of Size of
cores and cross - holes for screws (2*)
sectional area connection
connected per per phase
phase / PE (1*)
[mm²]
7 * 185²
8 * 185²
11 * 185²
11 * 185²
12 * 240²
14 * 240²
2 x 11 * 185²
2 x 12 * 240²
2 x 14 * 240²
7 * 185²
9 * 185²
11 * 185²
12 * 240²
2 x 9 * 185²
2 x 11 * 185²
2 x 12 * 240²
9 * 185²
11 * 185²
12 * 240²
(2*) Tightening torque:
M10 = 25 Nm; 18.5 ft. - lbs.
M12 = 50 Nm; 37 ft. - lbs.
3ADW000352R0101 DCS800-A Installation Manual e a
Without DC - fuses
Amount of holes for Size of
connection per phase; screws (2*);
For size D1 - D3 terminals Not for UL
are used
8 M12
8 M12
8 M12
16 M12
16 M12
16 M12
16 M12
16 M12
16 M12
16 M12
(3*) Diameter of all holes: 14 mm
51
Size
UL as per Nema 2 (3*):
Amount of holes per
phase for single drives;
For size D1 - D3
terminals are used
D6 D6
D7
D7P D7P
D7 D7
D7P D7P
D7 D7
Electrical Installation