ABB DCS800 Series Installation Manual page 49

Unit type
IAC [A~]
400 V / 500 V / 525 V
800 V
DCS800-A0x-1900-08-D
DCS800-A0x-2500-08-D
DCS800-A0x-3000-08-D
DCS800-A0x-3300-08-D
DCS800-A0x-4000-08-D
DCS800-A0x-4800-08-D
DCS800-A0x-6600-08PD
DCS800-A0x-8000-08PD
DCS800-A0x-9600-08PD
990 V
DCS800-A0x-2050-10-D
DCS800-A0x-2600-10-D
DCS800-A0x-3300-10-D
DCS800-A0x-4000-10-D
DCS800-A0x-5200-10PD
DCS800-A0x-6600-10PD
DCS800-A0x-8000-10PD
1200 V
DCS800-A0x-2600-12-D
DCS800-A0x-3300-12-D
DCS800-A0x-4000-12-D
Incoming Supply Sections
DCA63u-1000-0x-D
DCA63u-2000-0x-D
DCA63u-3000-0x-D
DCA63u-4000-0x-D
(1*) Recommended by ABB:
- Use cable type VPE (90°C; 194°F) with 4 cores
- AC - connection: U, V, W and PE
- DC - connection: L+, L- and 2 * PE
- Ambient temperature: 40°C; 104°F
- Load: 100 %
Recommended cross-sectional areas - tightening torques AC-connection
Amount of single Amount of holes per phase for
cores and cross -
sectional area
Group drives are connected via
connected per incoming supply units;
phase / PE (1*) For sizes D1 - D3 terminals are
[mm²]
1558 6 * 185²
2050 8 * 185²
2460 10 * 185²
2706 10 * 185²
3280 10 * 240²
3854 12 * 240²
5084 2 x 10 * 185²
6232 2 x 10 * 240²
7380 2 x 12 * 240²
1681 6 * 185²
2132 8 * 185²
2706 10 * 185²
3280 10 * 240²
4018 2 x 8 * 185²
5084 2 x 10 * 185²
6232 2 x 10 * 240²
2132 8 * 185²
2706 10 * 185²
3116 10 * 240²
1000 3 * 120²
2000 7 * 185²
3000 9 * 240²
4000 12 * 240²
(2*) Tightening torque:
M10 = 25 Nm; 18.5 ft. - lbs.
M12 = 50 Nm; 37 ft. - lbs.
3ADW000352R0101 DCS800-A Installation Manual e a
AC - connection (U, V, W) + PE
Size of
single drives; screws (2*);
Not for UL
used
8 M12
8 M12
12 M12
16 M12
16 M12
16 M12
16 M12
16 M12
16 M12
16 M12
8 M12
8 M12
8 M12
8 M12
UL as per Nema 2 (3*):
Amount of holes per phase for
single drives;
Group drives are connected via
incoming supply units;
For sizes D1 - D3 terminals are
used
(3*) Diameter of all holes: 14 mm
Electrical Installation
49
Size
D6 D6
D7
D7P D7P
D7 D7
D7P D7P
D7 D7