This manual introduces from Pylontech. Please read this manual before you Phantom-S install the battery and follow the instruction carefully during the installation process. Any confusion, please contact Pylontechimmediately for advice and clarification. Contents Safety Precautions..........................1 1.1 Before Connecting......................... 1 1.2 In Using .............................
1. Safety Precautions Reminding 1) It is very important and necessary to read the user manual carefully (in the accessories) before installing or using battery. Failure to do so or to follow any of the instructions or warnings in this document can result in electrical shock, serious injury, or death, or can damage battery, potentially rendering it inoperable.
Page 5
3) In case of fire, only dry powder fire extinguisher can be used, liquid fire extinguishers are prohibited; 4) Please do not open, repair or disassemble the battery except staffs from Pylontech or authorized by Pylontech. We do not undertake any consequences or related responsibility which because of violation of safety operation or violating of design, production and equipment safety standards.
Phantom-S lithium iron phosphate battery is one of new energy storage products developed and produced by Pylontech, it can be used to support reliable power for various types of equipment and systems. Phantom-S is especially suitable for application scene of high power, limited installation space, restricted load-bearing and long cycle life.
2.3 Equipment Interface Instruction This section details the front and back panel of the interface functions. PHANTOM Product Front Interface Start Button After turn on the Power Switch (back face), touch it 3sec to start up the battery, or touch 3sec to turn the battery into sleep mode (Soft-start/shut down).
PHANTOM Product Back Interface + Power Terminal - Power Terminal Dry Contact Terminal ON/Off Led Power Grounding Link Port 0/1 CAN/RS485 Console Switch Point Power Switch Power Switch: BMS standby, no power output RUN LED: to show the Power Switch is ON, and the equipment has electricity. ADD Switch (5) ADD Switch: 4 ADD switches, Dip1 to definite different baud rate (0 is 115200, 1 is 9600).
CAN Communication Terminal: (RJ45 port) follow CAN protocol, for output batteries information. RS485 R485 Communication Terminal: (RJ45 port) follow RS485 protocol, for output batteries information. Link Port 0, 1 Link Port 0, 1 Communication Terminal: (RJ45 port) follow RS485 protocol, for communication between multiple parallel batteries.
Power Terminals Power cable terminals: there are two pair of terminals with same function, one Lock Button connect to equipment, the other one paralleling to other battery module for capacity expanding. For each single module, each terminal can achieve charging and discharging function.
3. Safe handling of lithium batteries Guide 3.1 Schematic Diagram of Solution 3.2 Explanation of Symbols * Do not disconnect or disassemble by non-professional personnel. * Do not drop, deform, impact, cut or spearing with a sharp object. * Do not place at a children or pet touchable area. * Do not place near open flame or flammable material.
3.3 Tools The following tools are required to install the battery pack Wire cutter Crimping modular Plier Screw driver NOTE Use properly insulated tools to prevent accidental electric shock or short circuits. If insulated tools are not available, cover the entire exposed metal surfaces of the available tools, except their tips, with electrical tape.
4. Installation 4.1 Package Items Unpacking and check the Packing List For battery module package: Two power cables and one communication cable for each battery package: Grounding cable: 1000 2) For battery system connects to inverter: Two long power cables (current capacity 120A) and one communication cable for each energy storage system: 2000 2000...
4.2 Installation Location Make sure that the installation location meets the following conditions: The area is completely water proof. The floor is flat and level. There are no flammable or explosive materials. The ambient temperature is within the range from 0°C to 50°C. ...
Page 16
Back Face ① Put the battery into the cabinet; ② Drive the 4 pcs screws; ③ Connect the cables between battery modules ④ Connect the cables to inverter 19PISV0606 13/23...
Page 17
The power cables’ current capacity is 120A. If the battery string’s current over this limit, it must configure 2 pare external power cables to reach 240A. 19PISV0606 14/23...
Page 18
B. Power On Double check all the power cable and communication cable. (1) Switch power on Switch on all the battery modules and the green LED light below will be on: (2) The one with empty Link Port 0 is the Master Battery Module, others are slaves: (3) Touch the start button of master battery to power on, all the battery LED light will be on one by one from the Master battery: 19PISV0606...
Page 19
If all the battery LED lights on, and then off, which means the battery system is good and working. Installation with bracket: 19PISV0606 16/23...
Page 21
Aim at the 4 pare of Location Pin and Location Hole, stack the batteries together. And hasp the 4 agraffes together. 19PISV0606 18/23...
Page 22
Maximum 4 batteries can be athwart stacked: One or two batteries can be sidelong stacked: Cables connection and batteries system start are same as cabinet installation. 19PISV0606 19/23...
Page 23
NOTE After installation, do not forget to register online for full warranty: www.pylontech.com.cn/service/registration NOTE To start the system, if has grid power, it should turn on the inverter at first, to avoid current pulse of the inverter add on the battery bank.
5. Trouble Shooting Steps 5.1 Problem determination based on: 1) Whether the battery can be turned on or not; 2) If battery is turned on, check the red light is off, flashing or lighting; 3) If the red light is off, check whether the battery can be charged/discharged or not. 5.2 Preliminary determination steps: 1) Battery cannot turn on, switch on the lights are all no lighting or flashing.
Damaged batteries are dangerous and must be handled with the utmost care. They are not fit for use and may pose a danger to people or property. If the battery pack seems to be damaged, pack it in its original container, and then return it to Pylontech or an authorized dealer. NOTE Damaged batteries may leak electrolyte or produce flammable gas.
Page 28
Pylon Technologies Co., Ltd. No. 73, Lane 887, ZuChongzhi Road, Zhangjiang Hi-Tech Park Pudong, Shanghai 201203, China +86-21-51317699 | +86-21-51317698 service@pylontech.com.cn www.pylontech.com.cn...