Page 1 FORTERRA HSX OPERATOR´S MANUAL 04/2020 Tractor is Zetor. Since 1946.
Page 2 ZETOR This Operator’s Manual for the Zetor tractors, which we are presenting to you will help you to become familiar with the operation and maintenance of your new tractor. Although many of you have rich experience with the operation of other tractors, please, read the information contained in this Operator’s Manual very carefully.
Page 4: Table Of Contents
Aggregation tractor - machine/trailer ......................26 Tractors equipped with front end loader ...................... 26 Principles for operating tractors equipped with front end loader ..............27 Zetor tractors used for work in the woods ....................28 Safety labels ..............................28 Preventive daily maintenance ........................29 Preventive daily maintenance........................
Page 5 CONTENTS Switching on Work Lights and Beacons ...................... 43 Tractor Cab Lighting Control ........................44 Steps Lights Control ............................ 44 Day / Night Mode ............................44 Work Lights Memory ............................ 45 Automatic Work Lights Activation according to the Selected Driving Direction (FNR Automatics) ..... 45 Control panel on the right rear mudguard ....................
Page 6 CONTENTS Display - setting the automatic mode of the display backlight ..............72 Display - setting and calibration........................73 Travel speed calibration ..........................74 Display - machined area ..........................75 Machined area menu ........................... 75 Processed area - user selection ........................76 The processed area - setting of the width of aggregation ................
Page 7 CONTENTS Change the direction of drive........................105 Change the direction of drive by means of reversing lever ............... 105 Change the direction of drive - using the clutch pedal ................105 Gear shifting .............................. 106 Gear shifting - Using the clutch pedal ....................... 106 Gear shifting - using the clutch control button on the head of gear shifting lever ........
Page 8 CONTENTS Drive of agricultural machinery ........................131 Work with PTO shaft ..........................131 Display of revolutions of PTO shafts ......................131 Replaceable end points of rear PTO shaft ....................131 Control elements of PTO shafts ........................ 132 The buttons for activation of PTO shafts ....................132 Selection switch of rear PTO clutch revolutions (P.T.O.) ................
Page 9 Motor oils ..............................188 Oil in the gearbox and final drivehousing ....................188 Oil for the front driving axle ........................188 Oil for the front PTO ..........................188 Specification of oils for Zetor engines equipped by diesel particle filter ............ 189...
Page 10 Plastic lubricant for the tractor ........................189 A/C coolant ..............................189 Liquid for the cooling system of the tractors ....................189 Fuel for Zetor engines which are equipped with diesel paricle filter ............190 Urea (urea solution AUS 32) ........................190 Tractor greasing scheme ........................... 191 Safety instructions for lubrication of the tractor ..................
Page 11 CONTENTS Permitted maximum load of front axle (kg) ....................213 Permitted maximum load of rear axle (kg) ....................213 Permitted maximum weight of set 'tractor + mounted machine' (kg) ............213 Manoeuvrability condition .......................... 213 Front tires steerability ..........................214 Change of the load-bearing capacity of the front tyres (%) ...............
Page 12: Location Of Serial Numbers
LOCATION OF SERIAL NUMBERS FCL20S5001 1. Tractor data plate 2. Cab serial number 3. Engine serial number 4. Tractor serial number When ordering spare parts and within all written and oral communication always specify the data of your tractor that should be written in the frames below. Tractor type Tractor serial number Engine serial number...
Page 13 LOCATION OF SERIAL NUMBERS The 'right', 'left', 'front' and 'back' indications refer to the driving direction of the tractor. FCL20S5002...
Page 14: Safety Instructions For Users
SAFETY INSTRUCTIONS FOR USERS Pay increased attention to the parts in the instructions for use and maintenance indicated with this symbol. The symbol can be found next to all important warnings related to the operational safety. Follow these warnings and be particularly careful in these situations! Inform your colleagues and other users about these warnings.
Page 15: Used Pictograms
SAFETY INSTRUCTIONS FOR USERS Used pictograms Engine oil pressure SCR system failure Engine failure Transmission failure Engine stop Transmission oil temperature Engine coolant temperature Transmission automatic shifting Engine air filter clogged Transmission oil filter Engine rotational speed, automatic control Transmission, skip shift up Engine rotational speed, instantaneous Transmission, skip shift down decrease...
Page 16 SAFETY INSTRUCTIONS FOR USERS Clutch Battery charging condition Clutch temperature Seatbelt Front axle drive Engine glow plugs Four-wheel drive(automatic) Fuel level Differential lock Urea level warning Automatic differential lock Fuel Spring-loaded front driving axle, failure Area worked Suspended axle, automatic operating mode Hourmeter Suspended axle, lower Distance covered by the tractor since the...
Page 17 SAFETY INSTRUCTIONS FOR USERS Slow operation Rear fog lights Rear fog lights Beacon Push pedal Interior compartment illumination Release pedal Lighter Left direction lamp Timer Right direction lamp Horn Turn signals Windscreen wiper, intermittent Turn signal, first trailer Windscreen washer and wiper Turn signal, second trailer Windscreen wiper Position lights...
Page 18 SAFETY INSTRUCTIONS FOR USERS Seat adjustment, longitudinal (fore and aft) Hydraulic system, flow of oil Seat height adjustment Force regulation Seat adjustment, seatback recline Position regulation Seat tilt controller Lower working position Seat, lumbar adjustment, in and out Upper working position Seat, weight adjustment Fast rock lower Seat turning controller...
Page 19: General Safety Regulations
SAFETY INSTRUCTIONS FOR USERS General safety regulations The tractor may only be operated by a trained person that has a valid driving licence and has been  thoroughly acquainted with the operation and safety rules. Besides the safety instructions mentioned in the Operator´s Manual you are obliged to respect ...
Page 20: Driving Operation
 aggregated unit which may be influenced by the connected machine. During aggregation of Zetor tractors with machines and implements with high tensile resistance when  the engine speed drops and the engine tends to stall, the 1R, 2R reduced gears must not be used for...
Page 21: Risk Of The Tractor Overturning
SAFETY INSTRUCTIONS FOR USERS Risk of the tractor overturning The risk of the tractor overturning is increased especially when the following is used: a narrow wheel gauge  inappropriate tractor travelling speed  travel on the slope along a contour line or turning on the slope ...
Page 22: Leaving The Tractor
SAFETY INSTRUCTIONS FOR USERS Leaving the tractor Park the tractor only on an even land and where not possible, support with a shim assy.  Do not park the tractor with an attached implement in the lifted position.  Usually use the left-hand side tractor door when leaving the tractor. Look round whether any vehicle is ...
Page 23 SAFETY INSTRUCTIONS FOR USERS Health and environment protection The tractors are not equipped with special filters of air aspirated to the cab. Therefore, they are not  designed for work with aerosols and other harmful substances. Coolant, brake liquid, kerosene, diesel fuel, mineral oil and other oil products that are used for the ...
Page 24: Preventive Daily Maintenance
When handling the battery you must pay increased attention and avoid short-circuits. In tractors  equipped with a battery disconnector switch the disconnector off when handling the battery. Zetor tractors must not be operated with a disconnected battery as this may lead to a serious failure of  the tractor.
Page 25: Driver's Seat
FH13N002 Protection of cab against aerosols The cab of Zetor tractors in standard design is not designed for work with aerosols and other health hazardous substances. The level of cab protection in standard design complies with EN 15695-1:2009 standard - level 2 (only dust proof cab).
Page 26: Level Of External And Internal Noise
77,8 The level of vibrations on driver´s seat ZETOR tractors are classified in the category A and the class I/II/III. The category A includes all tractors with specified levels of vibration due to similar specifications of the construction. The following table presents the results of the measurement on the test bench according to the Commission Delegated Regulation (EU) No.
Page 27: Aggregation Tractor - Machine/Trailer
Tractors equipped with front end loader Zetor Tractors in standard design are designed for utilization in agriculture and are not designed for special purposes. Tractors designed for operation within the European Union must be equipped, in case of using front end loader, with a protective structure (FOPS - Falling Object Protective Structure) protecting drivers from potential falling objects.
Page 28: Principles For Operating Tractors Equipped With Front End Loader
ZETOR´s ap-proval. The loader may become dangerous as a result of not observing these instructions. ZETOR TRACTORS shall not be held responsible in case of any damage or injury. Use front end loader without additional weights on the tractor (danger of mutual contact). The load of ...
Page 29: Zetor Tractors Used For Work In The Woods
Standard tractors Zetor do not provide sufficient protection for operation in forest terrain as, for example, protection against a fal-ling tree or branch on a cab or penetration of objects to a cab. If Zetor tractor is utilized for forest work, a tractor operated within the European Union must be protected against these risks.
Page 30: Preventive Daily Maintenance
PREVENTIVE DAILY MAINTENANCE Preventive daily maintenance Perform this maintenance daily or after every 8 - 10 hours of operation at the latest. FCL20S5003 Fuel system leaks Check the fuel system for leaks, including the fuel tank. Repair any leaks immediately. The hole for draining dirt from the fuel tank is found in its bottom.
Page 31: Windshield Washer Tank
PREVENTIVE DAILY MAINTENANCE Windshield washer tank Windshield washer tank is placed on the rear wall of the cabin from the outside side. The washer tank capacity is 2 litres. In summer the reservoir should be filled with distilled water or mixture for washers. Antifreeze mixture for washers must be used in winter season for filling the washer tank.
Page 32: Air Cleaner
PREVENTIVE DAILY MAINTENANCE Air cleaner Repeated pressing the cup located on the bottom of the air cleaner cover in the direction of the arrows will blow out the dirt caught in the air cleaner cover. Perform other cleaning tasks: - every day when working with front-mounted implements or in a dusty environment - every 100 engine hours.
Page 33: Inspection Of Fouling Of Coolers
PREVENTIVE DAILY MAINTENANCE Inspection of fouling of coolers After opening the front hood, check that the fins of all installed radiators and the air conditioning condenser are not clogged. If they are clogged, clean the radiator fins with compressed air. After work with front implements and in case of cooler clogging After working with front-mounted machines: - Check the tightness of the connections of the external hydraulic circuit of the front three-point hitch control...
Page 34: Acquaintance With The Tractor
ACQUAINTANCE WITH THE TRACTOR Tractor user must be properly acquainted with recommended operating and safety rules for safe tractor operation in advance. It is too late to do it within operation! Safety cabin Use the left side of the tractor for getting on and getting off the tractor.
Page 35: Rear Window
ACQUAINTANCE WITH THE TRACTOR Rear window Is equipped with a handle and in an open position is locked by gas spruts. Rear window is heated. When driving on an uneven surface we recommend to secure the window in a closed position - danger of window cracking.
Page 36: Hinged Lid
ACQUAINTANCE WITH THE TRACTOR Hinged lid It is opened by turning the lid locking levers (1) and pushing it upwards. Close the hinged lid in reverse order . Opening the hinged lid increases the overall height of the tractor. Therefore, always close the lid when driving or parking in areas with reduced clearance.
Page 37: Rear View Mirrors
ACQUAINTANCE WITH THE TRACTOR Rear view mirrors Before driving or starting work, adjust the rear-view mirrors to allow you to monitor the whole drive way or working field. The rear-view mirrors are heated. FCL20S5015 Internal lighting To be turned on and off by means of a button marked with the arrow. *If the tractor is equipped with a light controller The interior lighting will automatically switch on for one to two minutes only in night mode when the battery...
Page 38: Cab Steps Lights (Only If Equipped With The Light Controller)
ACQUAINTANCE WITH THE TRACTOR Cab Steps Lights (only if equipped with the light controller) The cab steps lights are located in the cab roof above the left cab door. The cab steps lights automatically switch on, only in the night mode, for one to two minutes always when the battery disconnector is turned on or the ignition key is moved from position I to position 0.
Page 39: Driver's Seat Sears
ACQUAINTANCE WITH THE TRACTOR Driver's seat Sears P13N003 The driver's seat Sears can be made with a mechanical (A) or pneumatic (B) suspension. 1 - The seat suspension adjustment controller according to the driver's weight (turn it in the direction based on icons shown on the seat bellows) 2 - The seat height adjustment controller (release the controller to increase the seat height, tighten the controller to decrease the seat height)
Page 40: Passenger´s Seat
ACQUAINTANCE WITH THE TRACTOR Passenger´s seat Passenger´s seat is tiltable and placed on the left mudguard of the cabin. C15N047 Seat tilting out Passenger´s seat to be tilted out in the direction of an arrow (1) upward. Locking of the seat is done automatically.
Page 41: Control Panel On The Right Column Of The Cabin
ACQUAINTANCE WITH THE TRACTOR Control panel on the right column of the cabin 1 - Washer Button 2 - Front Wiper Cycle Switch 3 - Rear Wiper Switch 4 - 2-Position Front Windscreen Wiper Switch 5 - Rear Window Heater Switch 6 - Rearview Mirror Heater Switch 7 - Rear Work Light Switch (*not used if equipped with the light controller)
Page 42: Rear Window Wiper
ACQUAINTANCE WITH THE TRACTOR Rear window wiper The rear window wiper switch is located on the right pillar of the cab. The single-speed wiper of the rear window is controlled by a single-position switch. 0 - rear window wiper off 1 - rear window wiper on F18N012 Windscreen washer...
Page 43: Work Lights And Beacon Control Panel (Light Controller)
ACQUAINTANCE WITH THE TRACTOR *Work Lights and Beacon Control Panel (light controller) The control panel for work lights and beacons is located on the right side of the cab roof. It is forbidden to use work lights during road traffic. Use only original work lights.
Page 44: Switching On Work Lights And Beacons
ACQUAINTANCE WITH THE TRACTOR Switching on Work Lights and Beacons FHD20S5N015 Description of Work Lights and Beacon Control Panel 1 - Work Light Memory and FNR Automatic Control Switch 2 - Work Light Control Switch on the Front Turn Signal Lights Brackets (depending on equipment) 3 - Control Switch of Interior Front Work Lights on the Cab Roof 4 - Control Switch of Exterior Front Work Lights on the Cab Roof 5 - Beacon / Beacons Control Switch...
Page 45: Tractor Cab Lighting Control
ACQUAINTANCE WITH THE TRACTOR Beacons Control To turn on the beacons, press button (5) on the work light and beacon control panel. The beacons button is backlit in light green (orientation backlight); if the beacons are switched on by briefly pressing the button, the backlight of the button changes to dark orange (functional backlight).
Page 46: Work Lights Memory
ACQUAINTANCE WITH THE TRACTOR Work Lights Memory Press the ON / OFF button (1) to turn on the work lights memory; the backlight of the button changes to dark green (functional backlight). Press the relevant buttons to switch on the required configuration of work lights.
Page 47: Control Panel On The Right Rear Mudguard
ACQUAINTANCE WITH THE TRACTOR Control panel on the right rear mudguard The controls are located on the control panel on the right rear fender 1 - Rear PTO Preset Lever (for more information see AGRICULTURAL MACHINES DRIVE) 2 - Electrohydraulics Control Panel (more in the chapter ELECTROHYDRAULICS) 3 - Multiplier Preset Switch (see THE DRIVING OPERATION chapter)
Page 48: Lights Switch
ACQUAINTANCE WITH THE TRACTOR Lights switch a - illumination off b - side and end point lights on, illumination of licence label, illuminated c - all devices on in 'b' position. Lower beam head lights or head beam lights are engaged (according to the position of direction lights, lights and horn switches).
Page 49: Switch Box
ACQUAINTANCE WITH THE TRACTOR Switch box Switchbox is placed on the dashboard, see arrow. C18N165 Switch box key in the position (0) The voltage of all the equipment controlled via the key is disconnected. The key can be removed. C18N058 Switch box key in the position (I) The voltage is connected to all the equipment excluding starter.
Page 50: Manual Throttle
ACQUAINTANCE WITH THE TRACTOR Manual throttle a - idle run b - maximum supply The lever enables to set engine revolutions in the whole range (a) to (b). FHSXS5N003 Pedals and levers 1 - travel clutch pedal 2 - foot brake pedals joint by a catch 3 - throttle pedal C18N061 Reversing lever...
Page 51: Gear Shifting Lever
ACQUAINTANCE WITH THE TRACTOR Gear shifting lever - main gear shifting lever 1. button for disengaging clutch on the head of gear shifting 2. buttons of shifting individual gears of multiplier C18N062 Gear shifting scheme Reversing speeds can be shifted only by means of reversing lever.
Page 52: Pto Revolutions Preselection Lever
ACQUAINTANCE WITH THE TRACTOR PTO revolutions preselection lever The lever (1) is placed on the right side of driver's seat. For more information see the chapter on Drive of agricultural machines. F18N085 Auxiliary hydraulic switchbox control (external hydraulic circuit) Is placed in the upper part of right mudguard. A detailed description of control and function of integrated hydraulic switchboard (of external hydraulic circuit) follows in 'Hydraulic equipment' chapter of this instructions...
Page 53: Battery Disconnector
ACQUAINTANCE WITH THE TRACTOR Battery disconnector P18N100 The battery disconnector is located on the left side of the tractor behind the driver's stairs. A - Battery connected B - Battery disconnected C - Disconnector plate is located on the cover of the accumulator battery When the tractor is switched off, disconnect the battery using the battery disconnector.
Page 54: Heating Control Panel, * Air-Condition
ACQUAINTANCE WITH THE TRACTOR Heating control panel, * air-condition The control panel of the heating and of the air conditioning is located on the right side of the lower view of the cabin roof. A - valve heating controller B - fan controller C - air conditioner switch D - controller of air circulation in the cabin PGPPN125...
Page 55: Air Circulation In Cabin Control (D)
ACQUAINTANCE WITH THE TRACTOR Air circulation in cabin control (D) To switch the internal air circulation on and off, press the switch (D). - The internal air circulation is switched off (the diode under the switch is off), the outside air is sucked through the filters into the cab - The internal air circulation is switched on (the diode under the switch is on), air is sucked from the cab area...
Page 56: Fast Heating Of The Cabin Area
ACQUAINTANCE WITH THE TRACTOR Fast heating of the cabin area PGPPN131 Proceed as follows: 1 - Turn the heating valve control (A) to the right (HI) position (fully open heating valve) 2 - Use the fan control (B) to select the appropriate fan speed (position 1, 2, 3) 3 - Switch on the internal air circulation with the switch (D) (the diode under the switch is on) 4 - Adjust the air vents at the desired angle so that the people in the cab are not directly blown on 5 - After heating the cab space, switch off the internal air circulation by pressing the switch (D) and set the...
Page 57: Immediately After Cooling The Cabin
ACQUAINTANCE WITH THE TRACTOR Immediately after cooling the cabin PGPPN133 Immediately, after the cab has cooled down and the internal temperature has been lowered to the desired value, we recommend: 1 - Switch off the internal air circulation by pressing the button (D) 2 - By opening the heating valve (A), perform the continuous regulation of the air temperature, with the air conditioning on.
Page 58: Air-Condition And Heating Registers
ACQUAINTANCE WITH THE TRACTOR Air-condition and heating registers C20N030 Adjustable heating and air conditioning vents, front (A), side (B). Heating and air conditioning vents control A - Opening the vent, open the vent by pressing it, where indicated by the arrow B - Closing the vent, close the vent by pressing the slat of the vent in the direction of the arrow C - Changing the direction of air flow from the vent, hold...
Page 59: Fuel Tank
ACQUAINTANCE WITH THE TRACTOR Fuel tank A plastic tank of 270 litres volume is mounted as a standard for all types of tractors. Do not step on the fuel tank! F18N087 Fuel tank drain plug Plug for draining dirt and fuel off the fuel tank is in its bottom.
Page 60: Instrument Panel
INSTRUMENT PANEL Instrument panel - signal lamps P18N039 1 - green - signal lamp of left direction lamps 2 - blue - distance lights signal lamp Lights up with distance lights on. 3 - green - signal lamp of direction lights of the 1st trailer 4 - green - signal lamp of direction lights of the 2nd trailer 5 - orange - warning signal lamp 6 - blue - operational protection signal lamp.
Page 61: Instrument Panel - Instruments
INSTRUMENT PANEL Instrument panel - instruments P18N040 A - coolant thermometer B - fuel gauge C - engine speedometer D - information display Instrument panel - buttons P18N041 A - reset button, exit from menu of the instrument panel B - enter button, entry to menu of the instrument panel, item selection confirmation in the instrument panel menu C - button for rolling up in the instrument panel menu D - button for rolling down in the instrument panel menu...
Page 62: Display Description
INSTRUMENT PANEL Display description FHSX18N002 The basic display shows the following values: 1 - position of the reversing gear lever (more in the chapter RUNNING OPERATION) 2 - gear indicator of the torque multiplier, 1, 2 or 3 is displayed according to the selected gear 3 - position of the driving and reduced speed gear lever (more in the chapter RUNNING OPERATION) 4 - low air pressure indicator in the tractor's air pressure system 5 - graphical representation of the air pressure in the tractor's air pressure system...
Page 63 INSTRUMENT PANEL When the key in the switch box is moved to position I, the home screen is displayed on the display. C15N030 After about three seconds the main screen is displayed on the display. 1 - total operating hours (the value cannot be reset) 2 - operating hours of the tractor since the last reset of the value 3 - total distance covered (the value cannot be reset)
Page 64 INSTRUMENT PANEL 1 - immediate fuel consumption in L/100 km 2 - average fuel consumption in L/100 km since the last reset of the value 3 - average fuel consumption in L/hour since the last reset of the value 4 - fuel consumed since the last reset of the value P18N046 There are data regarding automatic switching off of the rear PTO shaft;...
Page 65: Display - Display Of Air Pressure In The Air-Pressure System Of The Tractor
INSTRUMENT PANEL Display - display of air pressure in the air-pressure system of the tractor P18N075 The air pressure in the air-pressure system of the tractor shown on the display of the instrument panel. 1 - the air pressure symbol, white illuminated, has no signaling function. 2 - the red display field;...
Page 66: Display - Resetting Data
INSTRUMENT PANEL Display - resetting data P18N047 The procedure for resetting data on the main screens where the data can be reset is as follows: 1 - Use the buttons (C) and (D) to select display of the corresponding main screen. 2 - Reset the data by longer pressing of the button (A) (RESET).
Page 67: Display - Service Menu
INSTRUMENT PANEL Display - service menu Entering the service menu: Enter the service menu by longer pressing of the button (B) (ENTER). Use the buttons (C) and (D) to select the items. The selected item is marked with a frame. Exiting the service menu: Press the button (A) to return from the service menu to the main screen.
Page 68: Display - Indicator Of Service Inspection Intervals
INSTRUMENT PANEL Display - indicator of service inspection intervals P18N070 The warning regarding an approaching maintenance date (service interval) is displayed if there are less than 25 operating hours remaining to the planned maintenance. The maintenance symbol (1) is shown on the display of the instrument panel. When the key in the switch box is moved from the position 0 to the position I, the main screen appears on the display and after several seconds the warning regarding an approaching maintenance (B) with the number of operating hours of the tractor (2) remaining to the maintenance date are displayed on the display.
Page 69: Error Signalling
INSTRUMENT PANEL Error signalling Errors arising during tractor operation are indicated by switching the corresponding signal lamp, acoustic signal and error message in the instrument panel display. If the error is indicated, the signal lamp still glows, even though the display is switched to the next display. If the error is not eliminated or the indicated state has not returned to a normal state: the corresponding signal lamp glows...
Page 70: Description Of The Display Of Error Messages
INSTRUMENT PANEL Description of the display of error messages 1 - The symbol of the defect significance. 2 - Node of the tractor where the defect appeared. 3 - Main display field - defect code. 4 - Secondary display field - defect specification. P18N074 Symbols of tractor nodes Engine...
Page 71: Display - Setting Language Mutation
INSTRUMENT PANEL Display - setting language mutation P18N077 Press the button (B) to enter the service menu 1 - use the buttons (C) and (D) to select the item Language; press the button (B) to enter the screen with language mutations. 2 - use the buttons (C) and (D) to select the required language mutation and press the button (B) for confirmation.
Page 72: Display - Setting Of Day And Night Backlight Of The Display
INSTRUMENT PANEL Display - setting of day and night backlight of the display P18N098 Enter the display settings menu. a - Use the buttons (C) and (D) to select the item for the day display backlight. Long press the button (B) to enter the screen for the display backlight setting (b).
Page 73: Display - Setting The Automatic Mode Of The Display Backlight
INSTRUMENT PANEL Display - setting the automatic mode of the display backlight P18N099 Enter the display settings menu. a - Use the buttons (C) and (D) to select the item (1) for the automatic mode of the display backlight. Long press the button (B) to enter the screen for setting the automatic mode of the display backlight (b).
Page 74: Display - Setting And Calibration
INSTRUMENT PANEL Display - setting and calibration FHSXS5N016 Press the (B) button to enter the service menu. 1 - Use the (C) and (D) buttons to select the setting item, press the (B) button to go to the setting menu screen.
Page 75: Travel Speed Calibration
INSTRUMENT PANEL Travel speed calibration FHSXS5N015 The instrument panel is calibrated after assembly at the factory. Re-calibrate the ground speed: - after the tires are considerably worn - when installing new tires - when replacing the instrument panel Calibration procedure - Mark a 100 m long track in a suitable area.
Page 76: Display - Machined Area
INSTRUMENT PANEL Display - machined area The processed area display shows the processed area in hectares. 1 - processed area in hectares 2 - processed area - average in hectares per hour 3 - fuel consumption - average in litres per hectare 4 - fuel consumption in litres from the start of the recording of the processed area.
Page 77: Processed Area - User Selection
INSTRUMENT PANEL Processed area - user selection PSH18N010 Enter the processed area menu - user selection. Three aggregation widths can be adjusted for each user. There is an extra memory of the processed area for each user. In the use selection menu (a) use the buttons (C) and (D) of one out of three users. Shortly press the button (B) to select the user with the set aggregation.
Page 78: Machined Area Record
INSTRUMENT PANEL Machined area record PHS18N012 Enter the aggregation settings menu. Make sure you have the correct user and the aggregate width (1) preset or set the user and the width of the aggregation. Each user has their own processed area values recorded; when a user changes, the processed area on the primary screen displays values valid for the selected user.
Page 79: Instrument Panel - Warning
INSTRUMENT PANEL Instrument panel - warning Replenish fuel When the fuel signal lamp (orange) is lit up, the prompt to refill the fuel appears in the display for about 3 seconds. If the fuel is not refilled, the prompt always appears in the display when the key is moved from the position ´0´...
Page 80: High Temperature Of The Cooling Liquid
INSTRUMENT PANEL High temperature of the cooling liquid PHS18N041 High temperature of the cooling liguid is indicated in several stages of warning A - informative - reduce the engine power B - warning - stop the tractor, set the engine to idling until the temperature of the cooling liquid is reduced C - caution - stop the engine, wait until the temperature of the cooling liquid is reduced and check the level of the cooling liquid;...
Page 81: Full Pushing Filter Of The Gearbox Distributor
INSTRUMENT PANEL Full pushing filter of the gearbox distributor PHS18N043 A - Caution - Replace the gearbox oil filter cleaner insert (see the maintenance instructions chapter) B - Warning - Fault in the sensor circuit, contact service Signalling of driver's seat PHS18N047 A - signalling - the operator left the driver's seat, sit back on the driver's seat B - defect - there is a defect in the circuit of the safety switch of the driver's seat, some functions of the...
Page 82: System Of Additional Treatment Of Exhaust Gases
SYSTEM OF ADDITIONAL TREATMENT OF EXHAUST GASES The tractor is equipped with an engine that meets the STAGE V and TIER 4f emission limits. Compliance with the emission limit is achieved, among other things, through a combination of two exhaust gas after- treatment systems: a- Diesel particulate filter (DPF), which is used to retain particulates in the exhaust gases.
Page 83: Conditions For Dpf Operation
SYSTEM OF ADDITIONAL TREATMENT OF EXHAUST GASES Conditions for DPF operation When the tractor is operated, the diesel particulate filter is fouled with solid particles during the fuel combustion while the engine is running. The regeneration of the diesel particulate filter in case of increased temperature of exhaust gases is performed at higher engine load.
Page 84: Error Signalling Of Dpf System
SYSTEM OF ADDITIONAL TREATMENT OF EXHAUST GASES Error signalling of DPF system Defects of the system of the diesel particulate filter when the engine is running are indicated by glowing or flashing of the orange or red signal lamp on the instrument panel and by the subsequent acoustic signal.
Page 85: Urea (Aqueous Urea Solution Aus 32, Def)
SYSTEM OF ADDITIONAL TREATMENT OF EXHAUST GASES Urea (Aqueous Urea Solution AUS 32, DEF) The used reagent is a mixture of 32.5% solution of synthetic urea and demineralized water. It is used as a reducing agent NOx for additional treatment of exhaust gases by SCR (selective catalytic reduction) of motor vehicles with diesel engines.
Page 86: Error Signalling Of Scr System
SYSTEM OF ADDITIONAL TREATMENT OF EXHAUST GASES Error signalling of SCR system Defects of the SCR system when the engine is running are indicated by glowing of the red (1) or orange (2) signal lamp on the instrument panel and by the subsequent acoustic signal.
Page 87: Indication Of Amount Of Urea In The Tank
SYSTEM OF ADDITIONAL TREATMENT OF EXHAUST GASES Indication of amount of urea in the tank P18N030 The amount of urea in the tank is displayed on the instrument panel on the main screen. a - If the urea level is higher than 32%, it is displayed as OK on the instrument panel. If the amount is below 32%, the real amount of urea in percentage is displayed.
Page 88: Reduction Of The Engine Power And Engine Revolutions
SYSTEM OF ADDITIONAL TREATMENT OF EXHAUST GASES Reduction of the engine power and engine revolutions If there is a serious error in the system or if the level of urea in the tank is low, the reaction of the system is reduced engine power output and revolutions.
Page 89 SYSTEM OF ADDITIONAL TREATMENT OF EXHAUST GASES P18N033 If the serious error is not removed, the second stage of engine power and speed reduction will take place. It is signaled to the tractor operator on the instrument panel display (1) or (2) together with an acoustic signal and warning indicator lights.
Page 90: Signalling Of Whether Dpf Is Full
SYSTEM OF ADDITIONAL TREATMENT OF EXHAUST GASES Signalling of whether DPF is full Information whether DPF is full is available on the main screen of the display. P18N035 By repeated pressing of button (A) you can switch between individual screens to the screen with the data on the status how much the DPF filter is full: 1 - percentage filling of DPF with carbon black The position (1) indicates the percentage filling of DPF filter with carbon black that fills the filter during...
Page 91: System Of Treatment Of Exhaust Gases - Setting
SYSTEM OF ADDITIONAL TREATMENT OF EXHAUST GASES System of treatment of exhaust gases - setting The regeneration of the diesel particulate filter in case of increased temperature of exhaust gases is performed at higher engine load. The system of regeneration of the diesel particulate filter DPF can be controlled through the menu of the engine setting on the instrument panel.
Page 92: Inhibition Of Regeneration Of The Diesel Particulate Filter - Regen. Inhibit
SYSTEM OF ADDITIONAL TREATMENT OF EXHAUST GASES Inhibition of regeneration of the diesel particulate filter - REGEN. INHIBIT The function of inhibition of regeneration of the diesel particulate filter (REGEN. INHIBIT) is used to block the process of DPF regeneration for safety reasons only during operation of the tractor in a flammable environment (e.g., storage of hay or straw).
Page 93 NOTES ...
Page 94: Driving Operation
DRIVING OPERATION Before a drive with the new tractor get to know how to shift gears and try individual positions of the shifting lever when the engine is stopped. During normal operation and before you set up, make sure that the technical condition ensures safe operation of the tractor.
Page 95: If You Do Not Succeed In Starting The Engine
DRIVING OPERATION If you do not succeed in starting the engine Return the key to '0' position. Wait 60 second and repeat the start. Never help the stopping engine by a starter. You are being exposed to the danger of starter damage.
Page 96: Starting The Engine While Using Coolant Heater
DRIVING OPERATION Starting the engine while using coolant heater FCL20S5016 With low temperatures of the surroundings, engine starting eases heating coolant. Leadin electrical installation and its protection against dangerous contact must be done pursuant to valid regulations 1. First plug the plug to the heater. 2.
Page 97: Error Signalling
DRIVING OPERATION Error signalling Errors arising during tractor operation are indicated by switching the corresponding signal lamp, acoustic signal and error message in the instrument panel display. If the error is indicated, the signal lamp still glows, even though the display is switched to the next display. If the error is not eliminated or the indicated state has not returned to a normal state: the corresponding signal lamp glows...
Page 98: Signalling Errors In The System Of Additional Treatment Of Exhaust Gases
Attention!Do not lower the engine load - risk of interruption of regeneration 2. Add urea 3. Add urea!The engine power may be limited. 4. Add urea!Engine power and revolutions may be limited 5. Increase the load or call Zetor service The engine power will be limited 6. Call Zetor service...
Page 99: Diesel Particle Filter
DRIVING OPERATION Diesel particle filter The exhaust system of a tractor is equipped with a diesel particle filter which serves for cleaning exhaust fumes. Solid particles (carbon particles) are collected and burned in diesel particle filter which originate by burning diesel. Filter of solid particles - indication of operation and failures of the system P18N058 The operation of the particulate filter is indicated by three indicator lights (1), (2) and (3) on the...
Page 100: Diesel Particle Filter Regeneration
DRIVING OPERATION Diesel particle filter regeneration P18N059 When the tractor is operated, the diesel particulate filter is fouled with solid particles during the fuel combustion while the engine is running. The full filter of solid particles is automatically regenerated (cleaned) while the engine is running by increased temperature of exhaust gases.
Page 101: Reversing Lever
DRIVING OPERATION Reversing lever The selection of the direction of travel drive is done by reversing lever (forward, backward). F - driving forward N - neutral R - driving backward The lever also serves for starting the tractor without the depressed clutch pedal.
Page 102: Gear Shifting
DRIVING OPERATION Gear shifting The tractors are equipped with a five-gear synchronized gearbox, three-gear torque multiplier, reversing and two- gear reduction. Five-gear gearbox is shifted by main shifting lever with buttons for disengaging the travel clutch (1) and for shifting the individual gears of multiplier (2). PHS18N005 Shifting road and reduced speeds H - road speeds...
Page 103: The Principles Of Appropriate Use Of Tractors
DRIVING OPERATION The principles of appropriate use of tractors The listed principles for tractor´s operation serve for facilitating the operation and guarantee corresponding service life of travel clutch! The description of the system of travel clutches The tractor is equipped with two individual travel clutches, one for travelling forward and one for travelling backward.
Page 104: Interrupted Sound Signal
DRIVING OPERATION Interrupted sound signal PHS18N052 If the tractor speed is regulated by partial released clutch pedal at higher engine revolutions than 1,200 rpm, an interrupted audio signal is generated and a warning on the display of the instrument panel is shown. If this situation occurs, immediately fully pres the clutch pedal to the end or release the clutch pedal to its upper position and wait until the acoustic signal is deactivated.
Page 105: Dead Start Of Tractor In Regular Operation - Automatic Dead Start Function
DRIVING OPERATION Dead start of tractor in regular operation - automatic dead start function - Use the control of travel clutch by reversing lever under the steering wheel for dead start of the tractor. - Select the slowliest L gear of torque multiplier for dead start of the tractor. Note: When starting or stopping the engine of the tractor, the fastest gear H is always automatically shifted.
Page 106: Change The Direction Of Drive
DRIVING OPERATION Change the direction of drive Change the direction of drive by means of reversing lever Change the direction of drive by means of reversing lever is done with travel speed lower than 10km/h. When you attempt to change the direction of drive in speed higher than 10 km/h, acoustic signal starts (uninterrupted tone) and the tractor engages neutral.
Page 107: Gear Shifting
DRIVING OPERATION Gear shifting - For shifting the gear speeds while travelling use the travel clutch control by a red button of clutch control on the head of gear shifting lever. - When shifting gears, press and hold the red button of clutch control on the head of gear shifting lever, release the gas pedal, throw out the gear, shift an applicable gear speed, release the red button and then increase the engine revolutions.
Page 108: Three-Gear Torque Multiplier
DRIVING OPERATION Three-gear torque multiplier Three-gear multiplier is a standard equipment of all types of tractors. Shifting individual gears of three-gear multiplier is controlled by two buttons on the head of main gear shifting lever. Increasing travel speed Decreasing travel speed It is done without travel clutch pedal depressed (under load).
Page 109: Multiplier Preselection Switch
DRIVING OPERATION Multiplier preselection switch FHSX18N023 The multiplier selector switch is located on the control panel on the right rear fender. Switching on is signaled by the on-screen symbol on the switch and the symbol on the dashboard display. If the preset switch is off, the multiplier gears can be set by the buttons on the gear shift lever. If the preset switch is on, multiplier gears are automatically set depending on the engine speed according to preset values.
Page 110 DRIVING OPERATION Display of values (engine revolutions) for automatic shifting of the multiplier The values (number of engine revolutions) stored by the system for automatic shifting of the multiplier when the buttons L and H are used are displayed on the corresponding main screen. More information in chapter INSTRUMENT PANEL.
Page 111: Front Drive Axle Control
DRIVING OPERATION Front drive axle control FHSX18N024 The front drive axle control button is located on the panel on the right rear fender. Pressing the part of the button marked with the front axle drive enabling switches on the manual drive mode of the front drive axle, after releasing the button returns to its original position.
Page 112: Automatically Disconnect The Front Axle - Manual Mode
DRIVING OPERATION Automatically disconnect the front axle - manual mode If the drive speed exceeds 20 kph, the front axle drive is automatically disconnected. Automatic drive disconnection is signaled by flashing a symbol on the instrument panel display, dashboard light and a button symbol.
Page 113: Suspension Front Drive Axle
DRIVING OPERATION Suspension front drive axle Tractors may also be equipped with a suspension of a front drive axle. The control buttons of the suspended front axle (1), (2) and (3) are located on the panel in the right rear fender. The button (1) is used to turn on the automatic suspension mode of the front drive axle.
Page 114: Differential Lock Control
DRIVING OPERATION Differential lock control FHSX18N030 The differential lock control button is located on the panel on the right rear fender. To activate the the differential lock press the button, which returns to its original position after releasing. Pressing the part of the button marked with the differential lock symbol will switch on the manual mode of the differential lock control.
Page 115: Manual Brake - Signalization
DRIVING OPERATION Manual brake - signalization If the tractor is not braked by a manual brake, a warning is displayed on a display (a letter P in a circle) and at the same time there is a sound signal. This situation occurs in two cases a - a tractor unbraked by a manual brake with engine running and a driver leaves its seat b - a tractor unbraked by a manual brake standing with...
Page 116: Foot Brakes
DRIVING OPERATION Foot brakes Foot brakes are disc type, wet, controlled hydraulically by the pressure oil from common gearbox filling with strengthening effect of the pump and with automatic pressure equalization in brake circuits. When driving on the road, both pedals must be connected with a latch.
Page 117: The Button For Temporary Deactivation Of Brakes Of The Trailer Or Semi-Trailer
DRIVING OPERATION The button for temporary deactivation of brakes of the trailer or semi-trailer FHSX18N031 Prior to using the button for temporary deactivation of brakes of the trailer or semi-trailer, it is always necessary to provide sufficient space in front of the tractor and behind the connected trailer or semi-trailer where no obstacles or persons will be present for the case that the effect of the parking braking will not be sufficient and the combination of vehicles moves.
Page 118: Air Brakes Of Trailers And Articulated Trailers
DRIVING OPERATION Air brakes of trailers and articulated trailers Control of air brakes of trailers (or semi-trailers) and control of the tractor brakes is performed so that the braking effect of both vehicles is synchronized. The operating pressure is set by the pressure regulator to the value of 740 ± 20 kPa. If the pressure drops below 550 - 40 kPa, secondary appliances are put out of operation by the by-pass valve.
Page 119: One-Hose And Two-Hose Brakes
DRIVING OPERATION One-hose and two-hose brakes 1. clutch head of one-hose brakes 2. clutch heads of two-hose brakes Clutch heads after disconnection or without a connected trailer, articulated trailer must be closed by a valve. F18N034 One-hose brakes Valve is marked with a black colour. Operating pressure is adjusted with the control valve at 600 ±...
Page 120: Hydraulic Brakes Of Trailers
DRIVING OPERATION *Hydraulic brakes of trailers Connect hydraulic brakes of trailer or articulated trailer to the quick couplings marked by an arrow. Control of hydraulic brakes of trailers (articulated trailers) and control of tractor brakes is done so that the braking effect of both vehicles is synchronized.
Page 121: Stopping The Tractor - Manual Brake
DRIVING OPERATION Stopping the tractor - manual brake FCL20S5022 Stop the tractor slowly under standard conditions. Shortly before stopping: 1. Depress the clutch pedal. 2. Shift the main gear shifting lever to neutral position. 3. With every stopping, secure the tractor against spontaneous dead start by manual brake. Stopping the engine FCL20S5023 After working on the tractor, when the engine has been fully loaded, it is necessary to ensure its cooling.
Page 122: Leaving The Tractor
DRIVING OPERATION Leaving the tractor FCL20S5024 Before leaving the tractor with a safety cabin, do not forget to remove the key from the switch box in '0' position (in position 'I' and 'II' the key cannot be pulled out). Tractor must be secured against spontaneous start: 1.
Page 123: Limiting Travel Speed
DRIVING OPERATION Limiting travel speed With the threat of exceeding the travel speed of 40 km/h, the maximum engine revolutions are automatically reduced. This function cannot be switched off. FHD14N068...
Page 124: Running In The Tractor
RUNNING IN THE TRACTOR General principles of new tractor run-in in first 100 hours of operation FCL20S5025 During first 100 hours of operation: Load tractor in a normal way, avoid operation with low or maximum engine revolutions  Avoid operation under partial loading of the engine ...
Page 125 NOTES ...
Page 126: Transportation
TRANSPORTATION Before you start, make sure that the technical condition of the tractor corresponds to requirements for safe operation. When a trailer or implement is attached, check its connection and proper fixation of the load. Never leave the tractor while it is moving to connect the trailer by yourself.
Page 127: Height Adjustment And Disassembly Of The Cbm Stage Hitch
TRANSPORTATION CBM stage quick-adjusting hitch It is designed for attachment of double-axle trailers or lighter single-axle semi-trailers. The guiding mouth is height adjustable. During work with various implements it may be necessary to adjust the height of the hitch or to disassemble the entire hitch.
Page 128: Modular System Of Hitches For Trailers And Semi-Trailers
TRANSPORTATION Modular system of hitches for trailers and semi-trailers C18N101 Module types: Fig. (B) - Swinging draw-bar console Fig. (C) - Swinging draw-bar console with a fixed pin Fig. (D) - Console with a ø 80 ball Disassembly, fig. (A): 1 - Remove the locking screw (1).
Page 129: Console With A Ø 80 Ball Module
TRANSPORTATION Console with a ø 80 ball module The console with a ø 80 ball is only used to connect semi-trailers with a hitching device designed for a ø 80 ball. Releasing the hitch, fig. (A): By moving the lever (1) in the arrow direction you will remove the locking wedge (2).
Page 130: Maximum Permissible Vertical Static Load Of Hitches For Trailers And Semi-Trailers
TRANSPORTATION Maximum permissible vertical static load of hitches for trailers and semi-trailers Hitch type Allowed Ø of Hitch type Allowed Ø of vertical hitch pin vertical hitch pin static load static load 30,5 1800 kg 2000 kg 38 mm CBM GTF30023D CBM GTF30014D 2000 kg 43 mm...
Page 131 NOTES ...
Page 132: Drive Of Agricultural Machinery
DRIVE OF AGRICULTURAL MACHINERY Work with PTO shaft Before attaching of an implement, driven by means of the tractor PTO shaft, check the speed compatibility of both, it means tractor PTO shaft and implement driven shaft (540 rpm or 1,000 rpm). Different PTO speed values may cause serious damages and injuries.
Page 133: Control Elements Of Pto Shafts
DRIVE OF AGRICULTURAL MACHINERY Control elements of PTO shafts The buttons for activation of PTO shafts Turning the PTO shaft on (at min. 1500 rpm) and off is done by the buttons located on the right pillar of the cabin. 1 - button for rear PTO shaft on / off 2 - button for front PTO shaft on / off If the engine is switched off and the rear or...
Page 134: Rear Pto Shaft Revolutions Preselection Lever
DRIVE OF AGRICULTURAL MACHINERY Rear PTO shaft revolutions preselection lever FHSX18N005 The tractor can be equipped with one of two PTO shaft speed selection systems. The system used for the specific tractor is marked on the sticker located at the rear PTO shaft speed lever. 1.
Page 135: Dependent And Independent Rear Pto Shaft Revolutions
DRIVE OF AGRICULTURAL MACHINERY Dependent and independent rear PTO shaft revolutions FHSX18N007 The system used for the specific tractor is marked on the sticker located at the rear PTO shaft speed lever. This system only has 540 or 1,000 rpm rear PTO shaft speed. A - Dependent PTO shaft speeds shifted (PTO SYNCHRO) N - Neutral position (rear PTO shaft terminal can be rotated freely.) B - Independent PTO shaft speeds shifted...
Page 136: Setting Automatic Disengagement Of Pto Shaft Clutch - Display Description
DRIVE OF AGRICULTURAL MACHINERY Setting automatic disengagement of PTO shaft clutch - display description PHS18N021 Gradually press the buttons (C) and (D) to display the screen of automatic switching off of the PTO shaft on the instrument panel. The following values are displayed on the screen: OFF-LIMIT (1) - position of arms of the rear three-point hinge where the clutch of PTO shaft is deactivated ON (2) - the current position of arms of the rear three-point hinge ON-LIMIT (3) - position of arms of the rear three-point hinge where the clutch of PTO shaft is activated...
Page 137: Work With Automatic Disengagement Of Pto Shaft Clutch
DRIVE OF AGRICULTURAL MACHINERY Work with automatic disengagement of PTO shaft clutch F18N050 Switch on automatic deactivation of the clutch of PTO shaft using the button (A) when the tractor is going or standing with the engine running. The activation of the function of automatic deactivation of the clutch of PTO shaft is indicated by the symbol A (1) on the display of the instrument panel (B).
Page 138: Facilitating Connection Of Joint Shaft Of An Aggregated Machine To The Tractor
DRIVE OF AGRICULTURAL MACHINERY Facilitating connection of joint shaft of an aggregated machine to the tractor F18N107 The button (1) located on the rear mudguards can be used to facilitate connection of the transmission shaft of the aggregated machine to the tractor. When the engine is running and the switch of the rear PTO shaft is deactivated, the rear PTO shaft starts to rotate when you press the button (1).
Page 139: Activation Of The Rear Pto Shaft - Independent Revolutions - Common Working Mode
DRIVE OF AGRICULTURAL MACHINERY Activation of the rear PTO shaft - independent revolutions - common working mode FHSX18N010 PTO shaft revolutions speed is dependent on engine revolutions. With the engine running while the rear PTO shaft clutch disengaged: A - Select the appropriate operating mode by the PTO shaft speed selector lever. B - Select the appropriate speed using the rear PTO shaft speed selector button.
Page 140: Activation Of The Rear Pto Shaft - Independent Revolutions - Stationary Working Mode
DRIVE OF AGRICULTURAL MACHINERY Activation of the rear PTO shaft - independent revolutions - stationary working mode FHSX18N011 PTO shaft revolutions speed is dependent on engine revolutions. With the engine running while the rear PTO shaft clutch disengaged: A - Select the appropriate operating mode by the PTO shaft speed selector lever. B - Select the appropriate speed using the rear PTO shaft speed selector button.
Page 141: Deactivation Of The Rear Pto Shaft - Independent Revolutions
DRIVE OF AGRICULTURAL MACHINERY Deactivation of the rear PTO shaft - independent revolutions Fhsx18N053 A - Switch off the rear PTO by pressing the button on the right-hand cab column or on the rear fender of the tractor. B - This condition is indicated by the fact that the rear PTO speed is not displayed on the instrument panel display.
Page 142: Rear Pto Shaft Switch - Dependent Speed - Ordinary Mode Of Operation
DRIVE OF AGRICULTURAL MACHINERY Rear PTO shaft switch - dependent speed - ordinary mode of operation FHSX18N014 The number and the meaning of the speed is dependent on the gear and the position of the reversing lever. The reduction lever position does not affect the number of revolutions of the rear PTO shaft in dependent mode - normal mode.
Page 143: Front Pto Shaft
DRIVE OF AGRICULTURAL MACHINERY Front PTO shaft Front PTO shaft is equipped with a solid six or twenty-one splined end point and it comes only in design of 1,000 revolutions. Tractor may be equipped with front PTO shaft with varied direction of spinning: In compliance with the direction of engine revolutions (standard)
Page 144: Activation Of The Front Pto Shaft - Stationary Working Mode
DRIVE OF AGRICULTURAL MACHINERY Activation of the front PTO shaft - stationary working mode FHSX18N016 PTO revolutions speed is dependent on engine revolutions. With the tractor stopped while the engine is running: A - We brake the tractor by a handbrake. B - Reverse gearshift lever must be shifted to neutral position.
Page 145: Maximum Transferred Output
DRIVE OF AGRICULTURAL MACHINERY Maximum transferred output PTO shaft Transferred output Front 1000 per minute 60 kW Rear 1000 per minute full output 540 per minute full output 1000E per minute 60 kW 540E per minute 60 kW F_02_46 Drive of machines with greater inertia masses. (crushers, rotary harrows, reaping machines, etc.) Cardan shaft for drive of these machines must be equipped with the so called freewheel clutch which...
Page 146: Hydraulic System
HYDRAULIC SYSTEM Hydraulic system The system consists of the inner and outer circuit. The source of pressurized oil is a gear pump. Oil is drawn from the common filling of the gearbox and final drive housing. Hydraulic pump The hydraulic pump cannot be disengaged. When the engine is running, the pump is in operation.
Page 147: Amount Of Oil Taken From Outer Hydraulic Drives
HYDRAULIC SYSTEM Amount of oil taken from outer hydraulic drives If the amount of oil in transmission decreases after disconnecting the tool due to its permanent outflow out of the tractor into the machine's hydraulic circuit, refill the oil missing. If the amount taken exceeds the limit, hydraulic pump can absorb air and can get damaged.
Page 148: Description Of The Functions Of Individual Positions Of Control Levers Of The Hydraulic Distributor
HYDRAULIC SYSTEM Description of the functions of individual positions of control levers of the hydraulic distributor FH12N049 Lever position Function Rear (upper) Pressurized oil flows to quick-couplers: 1, 3, 5 position Quick-couplers connected to the return line: 2, 4, 6 Central position Neutral Front (lower)
Page 149: Front Outlets Of The Outer Hydraulic Circuit
HYDRAULIC SYSTEM Front outlets of the outer hydraulic circuit On request, the tractor can be equipped with external hydraulic circuit outlets located at the front. The quick couplers (5) and (6) are pressurized, the quick coupler (0) is directly connected to the transaxle area and are intended for return oil from external hydraulic devices.
Page 150: Electro-Hydraulic System
ELECTRO-HYDRAULIC SYSTEM Control element functions C18N109 1. Lifting switch a - Transport, lifting b - STOP c - Regularity of lowering (working) d - Free position, fast sinking- automatic return of lever to (c) position by a spring 2. Blocking (in transport position) 3.
Page 151: Blocking Cancellation
ELECTRO-HYDRAULIC SYSTEM Blocking cancellation When you switch on the electric installation with the key of the switching box (I), the lifting device remains blocked electronically - the lifting and lowering function is deactivated; on the EHR-B control panel the diagnostic LED (7) and the vibration dampening LED (11) shortly light up - the system self-test is in progress.
Page 152: Transport Of Implements
ELECTRO-HYDRAULIC SYSTEM Transport of implements Shift the lifting lever (1) to position 'a' and block it with the moving latch (2). Blocking the lifting lever (1) by the moving latch (2) in position (a): A - Lever movement blocked B - Lever movement not blocked When the tractor with an attached implement is stopped, the implement must be lowered onto the ground (it must not be left in the lifted position).
Page 153: Limitation Of The Upper Position Of The Three-Point Hitch
ELECTRO-HYDRAULIC SYSTEM Limitation of the upper position of the three-point hitch It is activated with the control (5). The limitation can be implemented in the upper half of the three-point hitch lift. C18N117 Lowering speed The lowering speed of the three-point hitch is set with the control (3).
Page 154: Manual Setting Of Control Of Three-Point Hitch
ELECTRO-HYDRAULIC SYSTEM Manual setting of control of three-point hitch C18N120 Perform according to 'Cancel blocking' part and set the required position of elements with regard for the nature of performed works. To reach the depth of working tools, there is a control (4). For setting the kind of control and its mixing, use a control (6).
Page 155: Using The Rear Control
ELECTRO-HYDRAULIC SYSTEM Using the rear control The rear control is used to connect and disconnect implements. The lifting switching lever (1) on the EHR-B electro-hydraulic control panel must be in position (b) or (c). The designation symbols of buttons on both the tractor fenders correspond to the movement direction of the three-point hitch after their pressing.
Page 156: Indication Of Ehr-B Errors
ELECTRO-HYDRAULIC SYSTEM Indication of EHR-B errors The electronic part of the electro-hydraulic system continuously checks proper functioning of the system. Possible errors are indicated by repeated flashing combinations of the diagnostic LED (7). After the remedy of the error the diagnostic LED (7) goes off.
Page 157: Description Of Minor Errors Of The Ehr-B Electro-Hydraulic System
ELECTRO-HYDRAULIC SYSTEM Description of minor errors of the EHR-B electro-hydraulic system F18N109 Flashing combination of the diagnostic LED (7). Error location Possible cause of the error Long Short pause pause flashes flashes Right dynamometric pin Faulty dynamometric pin Left dynamometric pin (A) Faulty contact or interrupted conductor of the dynamometric pin Short-circuit of the dynamometric pin conductor...
Page 158: Hitches
HITCHES Rear three-point hitch It is used for connection of the carried half-carried agricultural machines and tools with hitch points of category II or III.N according to ISO. Category II. Hitch axis length 870 mm Ø of openings of connecting 28 mm balls of the lower draw-bars according to ISO...
Page 159: Safety Principles Of Working With The Three-Point Hitch
HITCHES Safety principles of working with the three-point hitch Persons that are not authorized to work with the attached implement must not stand between the tractor and the hitched machine (implement) - (A). Do not park the tractor with an attached implement in the lifted position (B).
Page 160: Limiting Draw-Bars
HITCHES Limiting draw-bars The limiting draw-bars - stabilizers (1) limit or completely prevent lateral swinging of the lower draw-bars. The adjustment of the left and right limiting draw-bar is performed by turning of the draw-bar pipe, see arrow. Both the limiting draw-bars must always be installed on the tractor.
Page 161: Upper Draw-Bar
HITCHES Upper draw-bar The upper draw-bar (1) has adjustable length. It is attached to the tractor to the console openings. When extending the upper draw-bar you must make sure that both the joints are unscrewed from the draw-bar pipe to the same length. F18N113 *Front three-point hitch It is designed for connecting front-mounted agricultural...
Page 162: Hydraulic Lock Of The Front Three-Point Hitch
HITCHES Hydraulic lock of the front three-point hitch Hydraulic locking of the front three-point hitch is performed in any position of the hydraulic cylinders with the ball valve in the front part of the tractor (2). Free position Valve levers are in the horizontal position - The hitch can be controlled from the cabin Locked position Valve levers are in the vertical position...
Page 163 NOTES ...
Page 164: Wheel Track Chang
WHEEL TRACK CHANG Gauges of the front wheels of the front drive axle of the tractors equipped with screwed footer discs When using foot discs on a tractor with a power higher exceeding 100 hp, it is necessary to take extra care and check and tighten the joints more often. It is not recommended to overload the foot discs.
Page 165: Front Wheels Track Of Front Drive Axle In Tractors Equipped With Non-Removable Discs
WHEEL TRACK CHANG Front wheels track of front drive axle in tractors equipped with non-removable discs Secure the tractor against motion first, heave the axle by a heaver and support. Tighten the nut of front wheels at a torque of 250 - 290 Nm. The change of wheel tracks is done by turning the wheel and mounting with rim offset to the inside, while the wheels are interchanged to keep the right direction of the tyre pattern with arrow to the front.
Page 166: Toe-In Of The Wheels Of The Front Driving Axle
WHEEL TRACK CHANG Toe-in of the wheels of the front driving axle Proper toe-in or toe-out (S) of front wheels in a tractor with front drive axle is measured on wheels´ rim Toe-in or toe-out is determined by the difference of measured values. Tractors with solid front drive axle b = a + 0 to 2 mm Tractors with suspension front drive axle...
Page 167: Front Drive Axle Fenders
WHEEL TRACK CHANG Front drive axle fenders There are two possible designs of the front drive axle fenders A - Fenders with fixed brackets. B - Fenders with swivel brackets where the axis of rotation corresponds only partially to the axis of rotation of the front wheel.
Page 168: Rear Wheels Wheel Track
WHEEL TRACK CHANG Rear wheels wheel track Gauges of the tractor rear wheels equipped with screwed footer discs Depending on the width of the rear tyres you can set the wheel tracks in the following range: Rear tyre width Wheel track (mm) 12,4-38 1425 - 1800...
Page 169: The Gauges Of The Tractor Rear Wheels Equipped With Solid Discs
WHEEL TRACK CHANG The gauges of the tractor rear wheels equipped with solid discs Rear wheels track 18,4-38 1725 460/85R38 1725 480/70R38 1725 520/70R38 1725 600/65R38 1725...
Page 170: Ballast Weights
BALLAST WEIGHTS Ballast weights are necessary to additionally load the tractor axles and to ensure manoeuvrability and stability of the tractor. *Rear wheel weights Combination Mass of weights of weights (kg) (pcs) 2x25 + 6x30 2+10 2x25 + 10x30 2+14 2x25 + 14x30 FHD20S5N045 Bottom weights...
Page 171: Weight Of The Front Three-Point Hitch
BALLAST WEIGHTS *Weight of the front three-point hitch Material Weight mass (kg) Cast-iron Concrete FHSXS5N011 Valve for filling tyre tubes with liquid All the tubes of the rear wheels are equipped with a valve that makes it possible to fill the tubes with liquid with the use of an adapter.
Page 172: Procedure Of Filling The Tyres With Liquid
BALLAST WEIGHTS Procedure of filling the tyres with liquid PGPPN181 1. Unload the tyre by lifting the tractor and turn it with the valve upwards (A). 2. Deflate the tyre and unscrew the valve insert. 3. Screw the adapter for water filling on and attach the liquid supply hose to it. 4.
Page 173: Wedging The Front Wheels
BALLAST WEIGHTS Wedging the front wheels Before lifting the rear wheels do not forget to secure the tractor against moving by wedging the front wheels. FHD20S5N050 Antifreeze solution for tyre filling An antifreeze solution may only be used for filling tyres if you have purchases additional tubes! Caution, the tractor is equipped with tubeless tyres by the manufacturer! Water for Calcium...
Page 174: Electric Installation
ELECTRIC INSTALLATION No additional interventions may be carried out on electric installation of the tractor (connection of other electric consumers) due to its possible overloading! With repairs of electric installation pay special attention in particular to manipulation with the battery to avoid any contact of electrolyte with skin or clothing.
Page 175: Battery Disconnector
ELECTRIC INSTALLATION Battery disconnector P18N100 The battery disconnector is located on the left side of the tractor behind the driver's stairs. A - Battery connected B - Battery disconnected C - Disconnector plate is located on the cover of the accumulator battery When the tractor is switched off, disconnect the battery using the battery disconnector.
Page 176: Accumulator Battery Maintenance
ELECTRIC INSTALLATION Accumulator battery maintenance PCLPN099 Keep the accumulator battery clean and properly fixed to the vehicle. However, the fixing device must not deform the battery case. In the case of polypropylene batteries the electrolyte level must not be below the minimum mark indicated on the case.
Page 177: Alternator
ELECTRIC INSTALLATION Alternator Charging is indicated by the red signal lamp on the united board instrument which must be deactivated after the start. If the engine is running and the red signal lamp is activated, it is a charging error. If this situation occurs, stop the tractor and contact the service centre.
Page 178: Fuse Panels
ELECTRIC INSTALLATION Fuse panels P18N006 There are three fuse panels located on the tractor: The fuse panel (A) is located on the left side of the tractor behind the driver's stairs, not far from the battery disconnector and it is accessible from the outside of the tractor.
Page 179 ELECTRIC INSTALLATION Fuse panel (B) (Tractors without *light controller only) FHSXS5N010...
Page 180 ELECTRIC INSTALLATION Fuse size Protected system Pos. Brake lights, warning lights interrupter Horn, beacon Appliances powered when the key is switched to position High beam lights with indicator light Position lights left, instrument panel light, license plate lights Position lights right Low beam lights right, fog light with indicator light 7.5A Low beam lights left...
Page 181 ELECTRIC INSTALLATION Fuse panel (B) (Tractors with *light controller only) FHSXS5N008...
Page 182 ELECTRIC INSTALLATION Fuse size Protected system Pos. Brake lights, warning lights interrupter Horn Appliances powered when the key is switched to position High beam lights with indicator light Position lights left, instrument panel light, license plate lights Position lights right Low beam lights right, fog light with indicator light 7.5A Low beam lights left...
Page 183: Checking The Adjustment Of The Front Grill Headlights
ELECTRIC INSTALLATION Fuse Panel (C) Pos. Fuse size Protected system F40 5A Socket in the cab F41 25A Three-pole socket on the right fender F43 10A Driver's seat heating F46 7.5A Socket in the cab F47 10A Trailer braking system F48 10A Trailer braking system F49 5A...
Page 184: Adjusting The Front Grill Headlights
ELECTRIC INSTALLATION Adjusting the front grill headlights The adjustment is performed simultaneously with all the screws for the vertical and horizontal direction of the beam. In the adjusted condition all the springs of non- adjusting screws must be pre-tensioned. Each headlight is adjusted separately.
Page 185: List Of Lamps
ELECTRIC INSTALLATION List of lamps FCL20S5038 Note Bulb location Voltage Power Bulb type Low beam headlight High beam headlight Work light (plowing) Low headlight (alternative) Direction indicator light P21W Position light Position / brake light 21W/5W P21/5W Interior lighting Roof work lights Roof work lights (*with light controller) License plate lighting is LED.
Page 186: Tractor Maintenance
Next service inspections always after covering another 500 EH but not later than 12 months after the previous service inspection. The service inspections are a part of tractor maintenance. The services authorized by Zetor will provide professional performance of service inspections according to the manufacturer's instructions.
Page 187: Steps Performed Outside The Interval Of 500 Hours Of Work
TRACTOR MAINTENANCE Steps performed outside the interval of 500 hours of work in a new tractor or tractor after a general overhaul subsequently after hour counter reading 1000 1500 2000 2500 3000 every...hours Check and adjust valve play 2000 Check the opening pressure of injectors and the function of 3000 injection nozzles...
Page 188: Filling And Filter Replacement
TRACTOR MAINTENANCE Filling and filter replacement in a new tractor or tractor after a general overhaul subsequently after hour counter reading 1000 1500 2000 every...hours Replace engine oil Replace the engine oil cleaner element Replace the fuel cleaner element 500 or once Replace the air cleaner element a year Replace the safety insert of the air...
Page 189: Used Operation Liquids And Filling - Quantities
The manufacturer does not take responsibility for any damages caused by the usage of service fillings that do not comply with requirements stated in this service manual. ZETOR service fillings To maintain best operational characteristics of your tractor, original operational Zetor fillings are recommended to be used. Motor oils...
Page 190: Specification Of Oils For Zetor Engines Equipped By Diesel Particle Filter
TRACTOR MAINTENANCE Specification of oils for Zetor engines equipped by diesel particle filter Classification ACEA Viscosity class SAE Performance class API E9/E7 15W-40 API CJ-4/SM Specification of the oil for the gearbox housing and the final drive housing Viscosity Class SAE Performance Class API...
Page 191: Fuel For Zetor Engines Which Are Equipped With Diesel Paricle Filter
TRACTOR MAINTENANCE Fuel for Zetor engines which are equipped with diesel paricle filter Diesel complies with EN 590 standard IMPORTANT NOTE! By using motor oil with elevated sulphur content, the service life of diesel particle filter can be significantly reduced.
Page 192: Tractor Greasing Scheme
TRACTOR MAINTENANCE Tractor greasing scheme Safety instructions for lubrication of the tractor The tractor maintenance may be performed only by the trained personnel thoroughly familiarized with  operational and safety principles. During maintenance of the tractor wear appropriate (specified) personal protective equipment ...
Page 193: Suspension Front Drive Axle
TRACTOR MAINTENANCE Suspension front drive axle FHD14N088 Position Name Number of number greasing points Greasing points Use grease with PTFE additives for greasing suspension front drive axle. Hitch for a single-axle semi-trailer Pos. Identification No. of lubrication points Hook pin bearings 0 to 4 (by version) PCLUN033...
Page 194: Three-Point Hitch
TRACTOR MAINTENANCE Three-point hitch Pos. Identification No. of lubrication points Pins of auxiliary hydraulic cylinders Lifting draw-bars FHSXS5N007 Hitch mouth for a trailer Pos. Identification No. of lubrication points Hitch mouth for a trailer PGPPN112 Technical maintenance of the tractors after a general overhaul of the main groups Run in the tractor after a general overhaul in accordance with the instructions for running in a new tractor.
Page 195 NOTES ...
Page 196: Maintenance Instructions
MAINTENANCE INSTRUCTIONS Most of operations of planned maintenance may be carried out by the driver or other user of the tractor. In case you do not have sufficient technical equipment, let the difficult operations carried out by a specialised repair shop. All works, connected with cleaning, lubrication and adjustments of the tractor or coupled mechanisms may only be carried out after stopping of the engine and other movable components except checks of brakes, recharging and hydraulic system.
Page 197: Checking The Oil Level In The Engine
MAINTENANCE INSTRUCTIONS Checking the oil level in the engine Check the oil level daily before starting work with the tractor in the horizontal position. Unscrew the dipstick, wipe it with a piece of cloth and screw it back in. After repeated removal of the dipstick the oil level must not drop below the lower mark.
Page 198: Replacing The Fuel Filter Element
MAINTENANCE INSTRUCTIONS Replacing the fuel filter element Replace the filter element after releasing the nut (1) and unscrewing the bowl (2). During the re-assembly of the cleaned bowl with the new filter element check proper seating of the bowl gasket. Bleed the fuel system. During the cleaning and replacement of the filter elements place a suitable vessel under the engine to catch dripping fuel.
Page 199: Dry Air Cleaner Maintenance Instructions
MAINTENANCE INSTRUCTIONS Dry air cleaner maintenance instructions Maintenance of the dry air cleaner includes the following activities: 1. Inspection of suction line (joint tightness, hose damage) 2. Checking the main filter cartridge (clogging, damage) 3. Checking the securing filter cartridge Replace damaged parts Air cleaner disassembly Disassemble the air cleaner according to the following...
Page 200: Reassembly Of The Air Cleaner Elements
MAINTENANCE INSTRUCTIONS Reassembly of the air cleaner elements When reassembling the air cleaner elements proceed in the reverse order. Observe the following points during the element reassembly: - Make sure the contact surfaces are clean. - During the assembly the elements must not get deformed and after installation they must not vibrate.
Page 201: Replacing Coolant
MAINTENANCE INSTRUCTIONS Replacing coolant Follow these steps: 1 - Open the heating tap and release the overpressure plug (C) on the expansion tank. 2 - Drain the coolant from the radiator. The drain plug (A) is accessible after opening the bonnet. 3 - Drain the coolant from the engine block.
Page 202: Check And Replacement Of Oil In Gear Box
MAINTENANCE INSTRUCTIONS Check and replacement of oil in gear box Draining and checking holes 1. drain plug of oil from clutch box 2. drain plug of oil from gearbox 3. drain plug of oil from final drive housing 4. drain plug of oil from final drive housing box 5.
Page 203: Replacement Of The Transmission Oil Cleaner Element With Hydraulic Pump Suction Filter
MAINTENANCE INSTRUCTIONS Replacement of the transmission oil cleaner element with hydraulic pump suction filter The oil cleaner is placed on the left side of the gearbox. Before replacing the oil cleaner element, place a suitable vessel for dripping oil under the tractor. 1.
Page 204: Filling, Controlling And Draining Hole Of Oil Of Front Drive Axle
MAINTENANCE INSTRUCTIONS Filling, controlling and draining hole of oil of front drive axle 1 - lubricating nipple of the kingpin 2 - sliding bearings (2 pieces) of the front driving axle 3 - drain opening of the final drive hous-ing oil 4 - filling and inspection opening of final drive housing oil (after removing of the inspection screw the oil level must reach the bottom edge of the inspection opening)
Page 205: Filter Installation Instructions
MAINTENANCE INSTRUCTIONS Filter installation instructions 1. Remove the old filter from the air duct orifice in the place of its mounting. 2. Remove the protective package from the new filter. 3. Insert the filter into the air duct orifice in such a way to make the air flow direction correspond to the flow direction through the filter in accordance with the arrow on the filter.
Page 206: Air-Conditioning Maintenance
MAINTENANCE INSTRUCTIONS Air-conditioning maintenance The most important task of the A/C system maintenance is to clean the A/C condenser (installed in front of the engine cooler). A clogged A/C condenser reduces not only the A/C system cooling efficiency, but also the engine cooling efficiency. Lift the hood, release and slide the radiator to the side and blow out with compressed air or flush with pressurized water (against the driving direction of the tractor).
Page 207: Checking The Air Systems For Leaks
MAINTENANCE INSTRUCTIONS Checking the air systems for leaks - fill the air reservoir to the maximum pressure (730 ± 20 kPa). - with the engine stopped the air pressure must not drop by more than 10 kPa in 10 minutes. Perform the leak check daily before driving with a trailer or semi-trailer.
Page 208: Recommended Inflation Values Of The Front Wheel Tyres
MAINTENANCE INSTRUCTIONS Recommended inflation values of the front wheel tyres Tyredimensions and design Principal working 540/65 R24 480/65 R28 14,9R24 420/70R24 activity For field work Inflation (kPa) 130-160 130-160 130-160 130-170 Load-bearing capacity 2410-2725 2150-2430 1490-1700 1665-1900 (kg) For road transport Inflation (kPa) 160-190 160-190...
Page 209: Tractor Shutdown And Recommended Points For Tractor Lifting
MAINTENANCE INSTRUCTIONS Tractor shutdown and recommended points for tractor lifting If the tractor is to be put out of operation for a shorter period, inflate the tyres to the value required for road transport. In case of a longer period of inactivity of the tractor (storage), support the tractor and reduce the pressure in the tyres to the minimum (the wheels must not touch the ground).
Page 210: Adjustment
ADJUSTMENT Almost all the following works require certain experience and more exacting service and diagnostic equipment. That's why we recommend to do the works at specialized or authorized workshops. Flat belt drive tension of accessories Flat belt drive tension of accessories (A) does not need to be adjusted.
Page 211: Foot Brake Adjustment
ADJUSTMENT Foot brake adjustment Before the adjustment of the foot brake the parking brake lever must be in the unbraked position and between the nut (1) and pin (2) in the disc brake lever (3) there must be some play. If you find zero play, loosen the nut (1) slightly. Lift both the rear wheels and instruct your assistant to turn one of them by hand.
Page 212: Main Technical Parameters
MAIN TECHNICAL PARAMETERS Main tractor's parameters (mm) Tractor type FORTERRA HSX note Tyre dimensions Front 14,9R24 Rear 580/70R38 Outline length with hitches with the front three-point hitch lowered 5100 without ballast weights Outline length with hitches without the front three-point hitch 4520 without ballast weights Width over the rear fenders...
Page 213: Technical Data Of Engines
MAIN TECHNICAL PARAMETERS Technical data of engines FORTERRA FORTERRA FORTERRA Tractor type HSX 120 HSX 130 HSX 140 Engine type 1418 1518 1618 Engine kind diesel, four-stroke with direct fuel injection, turbocharged Engine design in-line, vertical, water cooled Engine revolutions control electronic Number of cylinders Displacement...
Page 214: Permitted Maximum Load Of Front Axle (Kg)
MAIN TECHNICAL PARAMETERS Permitted maximum load of front axle (kg) Wheel track (mm) Travelling speed (km/h) 1590 - 1655 1730 - 1740 1800-1880 1890 -1955 2030 - 2040 5500 5500 5500 5500 5400 4400 4400 4400 4400 4100 4400 4400 4400 4400 4100...
Page 215: Front Tires Steerability
MAIN TECHNICAL PARAMETERS Front tires steerability Tyre dimensions Travelling speed 40 km.h 30 km.h Tyreload-bearing capacity Tyreload-bearing capacity (kg) (kg) Tyre Axle Inflation (kPa) Tyre Axle Inflation (kPa) 1 pc 1 pc 12.4-24 1140 2280 1425 2850 12.4R24 1360 2720 1455 2910 12.4-28 10PR...
Page 216: Bearing Capacity Of Rear Tires
MAIN TECHNICAL PARAMETERS Bearing capacity of rear tires Travelling speed Tyre 40 km.h 30 km.h dimensions Tyreload-bearing capacity (kg) Tyreload-bearing capacity (kg) Tyre Axle Inflation (kPa) Tyre Axle Inflation (kPa) 1 pc 1 pc 16.9-34 1900 3800 2380 4760 16.9R34 2430 4860 2600...
Page 217: Change Of The Load Capacity Of The Rear Tyres (%)
MAIN TECHNICAL PARAMETERS Change of the load capacity of the rear tyres (%) Travelling speed (km/h) diagonal radial + 40 + 50 + 20 + 23 - 20 Permitted combinations of wheels for tractors Combination Tire Front wheels Rear whels Tire Dimension of Dimension of...
Page 218: Performance On Rear Pto Shaft
MAIN TECHNICAL PARAMETERS Performance on rear PTO shaft FORTERRA FORTERRA FORTERRA Tractor type HSX 120 HSX 130 HSX 140 PTO power (kW ± 2%) at the nominal engine speed and engaged 1000 rpm of the PTO Engine in the running-in stage (until 68,2 75,4 80,8...
Page 219: Speed Of Tractor With Engine Revolutions Of 2 200 Rpm And Parameter Of Rear Wheels (Km/H)
MAIN TECHNICAL PARAMETERS Speed of tractor with engine revolutions of 2 200 rpm and parameter of rear wheels (km/h) Front direction Rear direction Speed Multiplier gear gear 16.9 - 38 18.4 - 38 16.9 - 38 18.4 - 38 48,0 *) 49,5 *) 44,7 *) 46,1 *)
Page 220: Dependent Pto Shaft Revolutions With Nominal Engine Revolutions
MAIN TECHNICAL PARAMETERS Dependent PTO shaft revolutions with nominal engine revolutions to the front to the rear multiplier gear degree 1000 1000 1 675 1 066 1 937 1 448 1 674 1 252 1 446 1 282 1 484 1 108 1 283 1 108...
Page 221: Independent Rear Pto Shaft Revolutions
MAIN TECHNICAL PARAMETERS Independent rear pto shaft revolutions PTO speed / engine speed PTO speed / engine speed 540/1913 621/2200 540E 540/1595 745/2200 1000 1000/1950 1128/2200 1000E 1000/1626 1353/2200 Speed of the Zuidberg front PTO Turning direction PTO speed / engine speed PTO speed / engine speed right (a) 1000 / 1920...
Page 222: Calculation Of Tractor Load Limit
MAIN TECHNICAL PARAMETERS Calculation of tractor load limit Connection of machines to the front or rear hydraulic arms must not exceed the allowed total load of the tractor, individual axles and tractor tyres. Therefore make sure before buying the aggregation that these assumptions are fulfilled using the following calculation: The following data must be known for the calculation: (kg) - instantaneous mass...
Page 223 MAIN TECHNICAL PARAMETERS Rear carried machine or front and rear carried combination 1. Calculation of the minimum front axle load G V min The calculated value of the minimum front axle load should be recorded in the table. 2. Calculation of the minimum rear axle load G H min The calculated value of the minimum rear axle load should be recorded in the table.
Page 224 MAIN TECHNICAL PARAMETERS Allowed load of the tractor and axles Table The real value according to the calculation must be lower or equal to the allowed value specified by the tractor manufacturer. Allowed value Real value according to according to the calculation manufacturer Total tractor weight...
Page 225 NOTES ...
Page 226: Index
INDEX Change the direction of drive - using the clutch pedal Change the direction of drive by means of reversing A/C coolant lever Accumulator battery Check and replacement of oil in gear box Accumulator battery maintenance Check of the Adjustment of the Low Beam Lights in the Acquaintance with the tractor Cab Roof Activation of the front PTO shaft - common working...
Page 227 INDEX Display - warning of low air pressure in the air-pressure Front wiper speed switch system of the tractor Fuel for Zetor engines which are equipped with diesel Display description paricle filter Display of revolutions of PTO shafts Fuel system leaks...
Page 228 Solid front drive axle front driving axle of the tractors Specification of oil for the front driving axle Preventive daily maintenance Specification of oils for Zetor engines equipped by diesel Preventive daily maintenance particle filter Preventive daily maintenance. Specification of the oil for the gearbox housing and the...
Page 229 The way of controlling the travel clutch by intervals Three-gear torque multiplier ZETOR service fillings Three-point hitch Zetor tractors used for work in the woods Tilting and protrusion of steering wheel Toe-in of the wheels of the front driving axle ...
Page 230 ...
Page 231 Operator's manual FORTERRA HSX 120 FORTERRA HSX 130 FORTERRA HSX 140 Edition: 4-100-2020 Publication No.: 222.213.550 6/2020 ZETOR TRACTORS a.s. Department of Technical Documentation Trnkova 111 628 00 Brno...
Page 232 Made in EU...

This manual is also suitable for:

Forterra hsx 130 Forterra hsx 140

Zetor FORTERRA HSX 120 Operator's Manual

Location of Serial Numbers

Safety Instructions for Users

Preventive Daily Maintenance

Acquaintance with the Tractor

Instrument Panel

System of Additional Treatment of Exhaust Gases

Driving Operation

Running in the Tractor

Transportation

Drive of Agricultural Machinery

Hydraulic System

Electro-Hydraulic System

Quick Links

Related Manuals for Zetor FORTERRA HSX 120

Summary of Contents for Zetor FORTERRA HSX 120