Section 2: Framing; In Wall And Corner Dimensions; Rear Vent, Rigid Or Flex; Top Vent, Flex - Montigo DelRay Square Series Installation & Maintenance Manual

Section 2: Framing

In Wall and Corner Dimensions

1). Frame in the enclosure for the unit with framing materials. The
framed opening for the assembled fireplace shown below in table
NOTE: When constructing the framed opening, please ensure there is
access to install the gas line when the unit is installed
3"
MIN.
1397
A
55"
1128
B
7
44 16 "
MIN.
C
457
18"
REAR VENTED
A B
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
DRSQ38 55'' 447/16''
TOP VENTED
A
Flex 59''
DRSQ38
Rigid 621/8''
8
1016
D
40"
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL 1/32"
Drawn by
TWO PLACE DECIMAL .015"
THREE PLACE DECIMAL .005" Revision / Date
ANGULAR .5
Revision
ALL BENDS ARE ASSUMED
TO BE 90 UNLESS NOTED
Finish
C D
OTHERWISE.
18'' 40"
B C D
447/16'' 18'' 40"
447/16'' 18'' 40"
Rear vent, rigid or flex
DELRAY
UNIT
HEAT DEFLECTOR
(REQUIRED FOR
FULL LOAD UNITS
ONLY)
FLOOR
REAR VENT 5/8" CHASE ASSEMBLY
Top vent, flex
1 1
8 8 2 " 2 "
FLEX FLEX
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PIPE PIPE
DELRAY DELRAY
UNIT UNIT
NAME DATE Description
DRSQ38-Rear Vent Chase Framing Assembly
DM 05/05/2020
DWG. NO.
DRSQ38-Rear Vent Chase Framing Assembly
MATERIAL
SCALE 1:24 WEIGHT: SHEET 1 OF 2
FLOOR FLOOR
TOP VENT 5/8" FLEX PIPE TOP VENT 5/8" FLEX PIPE
CHASE ASSEMBLY CHASE ASSEMBLY
REVISIONS REVISIONS
REV. REV. DESCRIPTION DESCRIPTION
- - . .
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED. THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED
8.000
1.000
Figure 3.b Framing dimensions (Straight wall & Corner Installation).
Installation
1
17 16 " OUTDOOR
WALL
MIN.
1
24 2 "
MIN.
55"
PTO4F
1
30 2 "
Top vent, rigid
OUTDOOR OUTDOOR
WALL WALL
DIMENSIONS ARE IN INCHES
TOLERANCES:
1 1
FRACTIONAL 1/32"
6 6 2 " 2 "
TWO PLACE DECIMAL .015"
1" 1" PTO4F PTO4F
THREE PLACE DECIMAL .005"
ANGULAR .5
MIN. MIN.
ALL BENDS ARE ASSUMED
TO BE 90 UNLESS NOTED
OTHERWISE. RIGID RIGID
PIPE PIPE
1 1
14 14 2 " 2 "
MIN. MIN.
MIN. MIN.
59" 59"
1 1
52 52 2 " 2 "
TOP VENT 5/8" RIGID PIPE TOP VENT 5/8" RIGID PIPE
15.000
DIMENSIONS ARE IN INCHES DIMENSIONS ARE IN INCHES
TOLERANCES: TOLERANCES:
FRACTIONAL FRACTIONAL
TWO PLACE DECIMAL TWO PLACE DECIMAL
1.000
DATE DATE CHANGED BY CHANGED BY THREE PLACE DECIMAL THREE PLACE DECIMAL
ANGULAR ANGULAR .5 .5
ALL BENDS ARE ASSUMED ALL BENDS ARE ASSUMED
- - - -
TO BE 90 UNLESS NOTED TO BE 90 UNLESS NOTED
OTHERWISE. OTHERWISE.
45.0°
56
1 1
OUTDOOR OUTDOOR
8 8 2 " 2 "
WALL WALL
NAME DATE
Description
DRSQ38 - Venting Assembly
Drawn by DM 05/05/2020
PTO4F PTO4F
1" 1" 9 9
DWG. NO. DRSQ38 - Venting Assembly
Revision / Date 6 6 16 " 16 "
MIN. MIN.
Revision
MATERIAL
Finish
SHEET 1 OF 2
SCALE 1:48 WEIGHT:
9 9
17 17 16 " 16 "
MIN. MIN.
1 1
62 62 8 " 8 "
9 9
55 55 16 " 16 "
DELRAY DELRAY
UNIT UNIT
FLOOR FLOOR
CHASE ASSEMBLY CHASE ASSEMBLY
NAME NAME DATE DATE Description Description
DRSQ36 - Venting Assembl DRSQ36 - Venting Assemb
1/32" 1/32" Drawn by Drawn by DM DM 12/5/2020 12/5/2020
.015" .015"
DRSQ36 - Venting Assembly DRSQ36 - Venting Assemb
DWG. NO. DWG. NO.
.005" .005" Revision / Date Revision / Date
Revision Revision
MATERIAL MATERIAL
Finish Finish
SCALE SCALE 1:32 1:32 WEIGHT: WEIGHT:
1
2 "
XG0230 - 052020
SHEET 2 OF 2 SHEET 2 OF