Table of Contents
Advertisement
Quick Links
IMPORTANT
IMPORTANT
SCAN THE QR CODE OR VISIT THE
WEBSITE TO VIEW THE MOST RECENT
VERSION OF THE MANUAL
WWW.MONTIGO.COM/PRODUCT-GUIDES
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result in serious injury,
death, or property damage.
— Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS
•
Do not try to light any appliance.
•
Do not touch any electrical switch; do not use any
phone in your building.
• Leave the building immediately.
• Immediately call your gas supplier from a neighbour's
phone. Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the fire
department.
— Installation and service must be performed by a qualified
installer, service agency or the gas fitter.
DANGER
HOT GLASS WILL CAUSE BURNS.
DO NOT TOUCH GLASS UNTIL
NEVER ALLOW CHILDREN
A barrier designed to reduce the risk of burns
from the hot viewing glass is provided with this
appliance and must be installed for the protection
of children and other at-risk individuals.
Installation & Maintenance Manual
C
COOLED.
TO TOUCH GLASS.
DelRay
INDOOR DIRECT VENT GAS FIREPLACE
DRL3613NI 16,000 BTU/hr Natural Gas or Propane Gas
DRL3613NI-2 16,000 BTU/hr Natural Gas or Propane Gas
DRL4813NI 21,000 BTU NG /19,000 BTU Propane /hr
DRL4813NI-2 21,000 BTU NG /19,000 BTU Propane /hr
DRL6013NI 28,000 BTU NG /25,000 BTU Propane /hr
DRL6013NI-2 28,000 BTU NG /25,000 BTU Propane /hr
DRL7213NI 35,500 BTU NG /32,000 BTU Propane /hr
DRL7213NI-2 35,500 BTU NG /32,000 BTU Propane /hr
®
Installation and service must be performed by a qualified installer,
US
service agency or the gas fitter. Check local codes and read all
Installer: Leave this manual with the appliance. Please refer to the
Montigo website for the most current version of the fireplace manual
Consumer: Retain this manual for future reference. Please refer to the
Montigo website for the most current version of the fireplace manual
Some materials used in the manufacturing process of this product can
expose you to Benzene which is known in the State of California to
cause cancer and birth defects or other reproductive harm. For more
information go to www.P65warnings.ca.gov
instructions prior to installation.
NOTICE
WARNING
XG0226 - 042220
Advertisement
Table of Contents
Related Manuals for Montigo DelRay DRL7213NI
Summary of Contents for Montigo DelRay DRL7213NI
- Page 1 DANGER Installer: Leave this manual with the appliance. Please refer to the Montigo website for the most current version of the fireplace manual Consumer: Retain this manual for future reference. Please refer to the HOT GLASS WILL CAUSE BURNS.
-
Page 2: Safety Alert Key
Introduction Congratulations on your purchase of a Montigo Fireplace. With over 30 years of experience, Montigo is committed to providing you with a gas fireplace that is not only a beautiful addition to your space, but that is also designed and manufactured to the highest safety, reliability and engineering standards. - Page 3 General BTU Listing CAUTION Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young children, and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are at-risk individuals in the house. To restrict access to a fireplace or stove, install an adjustable safety gate to keep toddlers, young children, and other at-risk individuals out of the room and away from hot surfaces...
-
Page 4: Table Of Contents
General Contents Safety Alert Key ........................2 Disable fans via remote .........................38 Introduction ..........................2 Basic Versions (if optional fan kit already installed): ............38 Section A: Before You Begin ........................5 Disable fans via harness ........................38 Installation Checklist ..........................5 Section 8: Removing & Installing the Screen / Door ............39 Standard Installation Checklist ......................6 Removing the Screen ..........................39 Rating Plate Sample ..........................7 Reinstalling the Screen ..........................39... -
Page 5: Section A: Before You Begin
• Should it be impossible to meet the venting requirements laid out in Section 3: Venting, please contact your Montigo dealer regarding the use of a Montigo Power Vent. NOTICE •... -
Page 6: Standard Installation Checklist
General Standard Installation Checklist This standard installation checklist is to be used by the installer in conjunction with, not instead of, the instructions contained within this installation manual. Customer Date Installed: Install Address: Location of Fireplace: Installer: Model (circle one): DRL3613NI, DRL3613NI-2, DRL4813NI, DRL4813NI-2 Dealer Phone: DRL3613LI, DRL3613LI-2, DRL4813LI, DRL4813LI-2, DRL6013LI, Serial #:... -
Page 7: Rating Plate Sample
General Rating Plate Sample Figure 1.1 Rating Plate for DelRay DRL3613NI Figure 1.2 Rating Plate for DelRay DRL4813NI XG0226 - 042220... - Page 8 General Figure 1.1 Rating Plate for DelRay DRL6013NI Figure 1.2 Rating Plate for DelRay DRL7213NI XG0226 - 042220...
-
Page 9: Section 1: Dimensions
Installation 36 48 Section 1: Dimensions DelRay 36, 48 Dimensions ELECTRICAL 57/16 DRL36 HAS 2 VENTING PORTS. DRL48 HAS 4 DRL36 361/2 1411/16 383/8 451/4 241/4 413/8 123/4 125/16 263/4 165/8 31/8 69/16 DRL48 481/2 1411/16 505/16 571/4 241/2 537/16 123/4 125/16 263/4 165/8 31/8 69/16 XG0226 - 042220... -
Page 10: Delray 60, 72 Dimensions
Installation NOTICE 60 72 DelRay DRL7213 uses 5/8 venting DelRay 60, 72 Dimensions ELECTRICAL 57/16 DRL60 601/2 1411/16 621/2 691/4 241/2 657/16 123/4 125/16 263/4 165/8 31/8 69/16 DRL72 721/2 1411/16 743/8 823/4 257/16 777/16 147/16 1315/16 161/2 31/8 69/16 515/16 XG0226 - 042220... -
Page 11: Lvp And Delicate Flooring
Installation LVP and delicate flooring Recommended floor recess considerations Flooring such as Luxury Vinyl Plank (LVP) and other vinyl flooring can DelRay fireplaces can be recessed into the floor, though a 10” be sensitive to radiant heat and changes in temperature. If using vinyl non-combustible hearth is recommended. -
Page 12: Section 2: Framing
Installation 36 48 Section 2: Framing Framing Dimensions 36", 48" 1). Frame in the enclosure for the unit with framing materials. The framed opening for the assembled fireplace shown below in table NOTE: When constructing the framed opening, please ensure there is access to install the gas line when the unit is installed 12.700 Framing header must... -
Page 13: Framing Dimensions 60", 72
Installation 60 72 Framing Dimensions 60", 72" 1). Frame in the enclosure for the unit with framing materials. The framed opening for the assembled fireplace shown below in table NOTE: When constructing the framed opening, please ensure there is The DRL60 and DRL72 access to install the gas line when the unit is installed comes standard with a non- combustible steel stud and... -
Page 14: Clearances
Installation 36 48 Clearances When installing a shelf over the top of the fireplaces, the following guidelines must be adhered to: 1'' all around DRL3613*I 21" 2" 1" 0" 6" 2" on the horizontal 1'' all around DRL4813*I 21" 2" 1"... -
Page 15: Standard Installation
Installation 36 48 36, 48 Standard installation 36, 48 Standard installation (Shelf over) NO RECESS NO RECESS NON-COMBUSTIBLE FACING NON-COMBUSTIBLE FACING DRL36 DRL48 DRL36 DRL48 IMPORTANT IMPORTANT 16" 130° 150° 16" 130° 150° Temperatures are based Temperatures are based 12" 140° 160° 12" 140° 160° off of the minimum off of the minimum enclosure size at a 3 hour... -
Page 16: Vented Installation (Cool Wall Release)
Installation 36 48 36, 48 Vented installation (Cool Wall Release) NO RECESS COMBUSTIBLE FACING NO FANS DRL36 DRL48 IMPORTANT 16" 95° 90° Temperatures are based off of the minimum 12" 95° 95° enclosure size at a 3 hour 8" 100° 100°... -
Page 17: Standard Installation
Installation 60 72 60, 72 Standard installation 60, 72 Standard installation (Shelf over) NO RECESS NO RECESS NON-COMBUSTIBLE FACING NON-COMBUSTIBLE FACING DRL60 DRL72 DRL60 DRL72 IMPORTANT IMPORTANT 16" 140° 145° 16" 140° 145° Temperatures are based Temperatures are based 12" 155° 160° 12" 155° 160° off of the minimum off of the minimum enclosure size at a 3 hour... -
Page 18: Vented Installation (Cool Wall Release)
Installation 60 72 Vented installation (Cool Wall Release) NO RECESS COMBUSTIBLE FACING NO FANS DRL60 DRL72 IMPORTANT 16" 100° 100° Temperatures are based off of the minimum 12" 105° 105° enclosure size at a 3 hour 8" 115° 115° burn time 4"... -
Page 19: Full Load Versions
Installation Section 3: Venting Montigo offers a variety of direct venting and termination options. The WARNING direct vent termination location MUST be selected such that it is the highest point in the venting assembly. It should also be selected such that it provides the shortest vent run possible. -
Page 20: Section 3-3-1: Venting Layout
Installation 36 48 Section 3-3-1: Venting Layout DRL36 & DRL48 Venting - Wall and roof termination OUTDOOR WALL Maximum total vent run allowed is 34 ft. (V+H ≤ 34ft.) FLEX For longer vent runs, a power vent is required PIPE V + H are measured from the center of vent elbows MTO-4F Maximum vertical run allowed is 34 ft. (V max). Maximum horizontal run allowed is 20 ft. (H max). Elbows: 13"... -
Page 21: Drl60 Venting
Installation OUTDOOR WALL DRL60 Venting - FLEX PIPE Wall and roof termination OUTDOOR WALL MTO-4F Maximum total vent run allowed is 34 ft. (V+H ≤ 34ft.) FLEX For longer vent runs, a power vent is required PIPE V + H are measured from the center of vent elbows MTO-4F Maximum vertical run allowed is 34 ft. (V max). 13"... -
Page 22: Drl72 Venting
Installation OUTDOOR WALL DRL72 Venting - FLEX PIPE Wall and roof termination OUTDOOR PTO-4F WALL MTO-4F Maximum total vent run allowed is 34 ft. (V+H ≤ 34ft.) FLEX For longer vent runs, a power vent is required PIPE V + H are measured from the center of vent elbows MTO-4F Maximum vertical run allowed is 34 ft. (V max). 13"... -
Page 23: Co-Linear Venting Into Existing Masonry Chimney
NOTICE bending • A maximum of two certified couplers may be used per length of 3" liner • DelRay co-linear installation requires reducing from Montigo 4/7 The unit must be fully enclosed while maintaining clearances to to Duravent 4x6⅝ combustibles detailed elsewhere in this manual... -
Page 24: Section 3-2: Installing A Roof Vent Termination
Installation 36 48 Section 3-2: Installing a Roof Vent Termination Section 3-2-1: Roof Venting termination • The maximum termination point is 32’ above the fireplace (NOTE: if the maximum termination height is used, the flame pattern may be affected). • The Vertical termination must be a minimum 2’ higher than where the termination exits the roofing materials, (asphalt shingles, cedar shakes, etc). -
Page 25: Section 3-3: Installing A Wall Mounted Termination
NOTE: If subject to a highly corrosive environment A Termination with a MOSR Frame is installed from the inside of the i.e. Seaside, Montigo recommends using Stainless Steel Termination. structure. These are commonly used in high-rise construction. -
Page 26: Section 3-3-2: Venting Components
• Montigo recommends the use of a flex section for the first section of venting connected directly to the fireplace, offering greater flexibility of installation and absorption of movement. -
Page 27: 4/7 Venting Components
Storm Collar Roof Flashing MRF7 (1/12 - 7/12 pt.) MRF12 (7/12 - 12/12 pt.) Vertical vent restrictors PVVR8 PVVR15 Heat Shield RHS100 PVVR25 Heat Guard MTKOG Montigo Fireplace PVA5487 Adaptors PVA5487 (5/8 to 4/7 reducer) Adapter (5/8 to 4/7 reducer) XG0226 - 042220... -
Page 28: Section 3-3-2.2: 4" X 7" Alternate Venting Components
Installation The following venting components are approved for use with Montigo products. Please contact your local Montigo dealer for further information. 36 48 Section 3-3-2.2: 4” x 7” Alternate Venting Components Component Montigo P/N Duravent P/N MetalFab P/N Flexmaster NOTES Duravent adaptor is designed for For painted black finish... -
Page 29: Section 3-3-2.2: Alternate Venting Components 5"/8
Section 3-3-2.2: Alternate Venting Components 5"/8" The following components are approved for use with Montigo products. Please contact your local Montigo dealer for further information. Component Montigo P/N Duravent P/N ICC P/N MetalFab P/N Selkirk P/N Flexmaster P/N NOTES Duravent adaptor is designed... -
Page 30: Flexmaster As Alternate Venting
Flexmaster Flex includes all and any prepackaged vent kits by Montigo containing Flexmaster venting. All Montigo prepackaged vent kits may be used on any Montigo residential unit fireplace. When using a Power vent you must use Montigo pipe only. VERTICAL THROUGH THE ROOF: HORIZONTAL FLEX RUN REQUIREMENTS: Follow venting graph for each model as required. -
Page 31: Section 3-3-3: Heat Shields 4''/7
Installation 36 48 Section 3-3-3: Heat Shields 4''/7'' Installing a Wall Mounted RHS100 Heat shield DRL36, DRL48 HEAT SHIELD DRL36, DRL48 HEAT SHIELD Use the RHS100 within 36" horizontal or 60" vertical. To install the RHS100, Slide the Inner Section over the vent pipe that will connect to the fireplace. -
Page 32: Section 3-3-4: Heat Shields 5''/8
Installation Section 3-3-4: Heat Shields 5''/8'' Installing a Wall Mounted RHS101 Heat shield Use the RHS101 where any of the dimensions are within the parameters shown, figure 15.d To install the RHS101, Slide the Inner Section over the vent pipe that will connect to the fireplace. Then fasten the vent pipe to the back of the fireplace with a minimum of three sheet metal screws. -
Page 33: Section 4: Wiring
DRL7213*I Installation of the wall switch Montigo supplies 15' of low voltage wire to be plugged into the control board. Connect to a standard single pole ON/OFF switch to the location of your choice. You may extend these wires up to 30' in length with a wire of equal quality. -
Page 34: Drl**13 (N/L) I-2 Wiring Diagram
Installation DRL**13 (N/L) I-2 Wiring Diagram BATTERY PACK 1.5V AA TYPE 1.5V AA type 1.5V AA TYPE 1.5V AA type SPARK GREEN 1.5V AA TYPE 1.5V AA type MAIN Power WHITE 120vac 60 hz 1.5V AA TYPE 1.5V AA type BLACK 6 amps SENSOR... -
Page 35: Section 5: Installing The Gas Line
N.P.T. plug to be fitted with a hose barb. unit or worse, a gas leak. • Montigo requires a service shut off valve be located in an accessible location to isolate the gas supply. • Only install gas shut-off valves approved for use by the state, province, or other governing body in which the fireplace is being installed. -
Page 36: Section 6: Finishing
Installation Section 6: Finishing Finishing Around the Fireplace Finishing when using a Cool Wall Advantage kit or vented chase (Cool Fireplace Facing When sizing the finish material for your fireplace, it is important to Wall Release) remember the following: THE OPENING MUST NOT BE OBSTRUCTED IN ANY WAY - to do so restricts the air supply for the control compartments Fireplace Facing and heat exchanger it also prevents access for servicing controls. -
Page 37: Chase Venting (Optional)
Installation NOTICE Cement board is not needed when the chase is vented, drywall can be used to finish up to the fireplace opening. Chase venting (optional) Sidewall clearances An opening in the finished enclosure can keep temperatures within a Side wall clearances are 4". Combustible surrounds may be installed safe level for a TV installation. -
Page 38: Disable Fans Via Remote
This can be done through the remote control (See instructions) Sides (Qty 2) or by disconnecting the fan harness. Montigo is NOT responsible for damage to facing materials, and items placed above the Cut standard Gyproc / Drywall board to complete the installation of fireplace (eg. -
Page 39: Section 8: Removing & Installing The Screen / Door
Installation Section 8: Removing & Installing the Screen / Door Removing the Screen Removing the door Follow the steps below to remove, or install the fireplace screen and The door is removed in a few simple steps. Follow these steps below door. Before beginning any screen or glass removal, make sure that the to unlatch the door buckles and remove the door. -
Page 40: Propane Conversion (High-Low Burner)
Installation Gas conversion steps vary based on what burner the unit is HIGH-LOW RIBBON installed in the fireplace. Check the burner hole pattern to ensure BURNER BURNER you are using the right instructions. Propane Conversion (High-Low Burner) Parts included To convert the DelRay from 1. - Page 41 Installation 6. Use screwdriver to carefully detach spring clip from the pilot 10. The pilot size can be adjusted using a flathead screwdriver to hood. (Spring clip will be reused) adjust “pilADJ” screw shown Figure 13.g Adjust pilot size Figure 13.d Removing the spring clip 7.
- Page 42 Installation should be carried out in a clean environment. WARNING! This modulating conversion kit must ONLY be applied as part of a conversion kit supplied by montigo for the specific appliance, and type of fuel, being converted. WARNING! Correct operation of the system cannot be guaranteed if the conversion kit or valve has been dropped or has sustained a strong impact.
-
Page 43: Propane Conversion (Ribbon Burner)
Installation Gas conversion steps vary based on what burner the unit is HIGH-LOW RIBBON installed in the fireplace. Check the burner hole pattern to ensure BURNER BURNER you are using the right instructions. 36 48 Propane Conversion (Ribbon Burner) Parts included 1. Shut off gas supply. To convert the DelRay from Natural Gas to Propane, install the conversion kit listed in the... - Page 44 Installation 36 48 6. Use screwdriver to carefully detach spring clip from the pilot 10. The pilot size can be adjusted using a flathead screwdriver to hood. (Spring clip will be reused) adjust “pilADJ” screw shown Figure 13.g Adjust pilot size Figure 13.d Removing the spring clip 7.
-
Page 45: Section 9: Installing The Accessories
Installation Section 9: Installing the Accessories Installing the Fireglass or Optional Glass Media The unit is supplied with fireglass. Optional fireglass may be purchased from the dealer. Remove the Door as shown in the previous Instruction. Once the glass door is removed place the firestones randomly across the pan and the burners. -
Page 46: Delray 48" Optional Log Kit Installation
Installation C C D D DelRay 48" Optional Log Kit Installation The Fireplace has the option of installing a drift wood log set. Once LGS77 LGS77 the base media of fireglass, firestones, or speckled stones has been placed the log set can be installed. Ensure logs are securely placed and will not tip or fall. -
Page 47: Delray 60" Optional Log Kit Installation
Installation LGS59 LGS59 DelRay 60" Optional Log Kit Installation The Fireplace has the option of installing a drift wood log set. Once LGS77 LGS77 the base media of fireglass, firestones, or speckled stones has been placed the log set can be installed. Ensure logs are securely placed and will not tip or fall. -
Page 48: Delray 72" Optional Log Kit Installation
Installation LGS77 LGS77 LGS57 LGS57 LGS59 LGS59 DelRay 72" Optional Log Kit Installation The Fireplace has the option of installing a drift wood log set. Once the base media of fireglass, firestones, or speckled stones has been placed the log set can be installed. Ensure logs are securely placed and will not tip or fall. -
Page 49: Remote Operation (Full Load Units)
Operation Remote Operation (Full Load Units) The Proflame 2 System consists of the following elements: 1. Pilot Assembly Blue Back lit LCD display 2. Proflame Gas Valve. 3. Proflame 2 Control Module On/Off Key 4. Wiring Harness Thermostat Key 5. Variable Speed fans Up/Down Arrow Key 6. -
Page 50: Initializing The System For The First Time
Operation Initializing the System for the first time Turn Off the Fireplace 1. Set master override switch to off position. 2. Install four (4) AA batteries into the battery holder. With the system On, press 3. Install three (3) AAA batteries in the back of the remote the On/Off Key on the control. -
Page 51: Room Thermostat (Remote Control Operation)
Operation Room Thermostat (Remote Control Disabling Thermostat Operation) Some jurisdictions and bedroom installations require the thermostat to be disabled. The Remote Control can operate as a room thermostat. The 1. Partially take out one battery. Insert the battery while holding thermostat can be set to a desired temperature to control down the thermostat button. -
Page 52: Pairing Issues
Pairing Issues Some newer wi-fi capable transmitters PN# 0.584.080 (Montigo part RGC3105), and older IFC control board PN# 0.584.307 (Montigo part RGC3095) require that the wi-fi function in the transmitter be turned OFF before trying to pair or sync the components. First identify the supplied transmitter, the RGC3105 will have a wi-fi symbol on the •... - Page 53 Operation DANGER HOT GLASS WILL CAUSE BURNS. DO NOT TOUCH GLASS UNTIL COOLED. NEVER ALLOW CHILDREN TO TOUCH GLASS. A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and must be installed for the protection of children and other at-risk individuals.
-
Page 54: Section 10: Cleaning And Maintenance
Operation Section 10: Cleaning and Maintenance General Pilot Burner Adjustment. • Have the fireplace and installation inspected yearly. The inspection 1. Locate Pilot Adjustment Screw. (See figure 28) must include, but is not limited to, the following: 2. Adjust pilot screw to provide properly sized flame as shown. •... -
Page 55: Pod - Pilot On Demand
Installation POD - Pilot on Demand What is POD mode? Installing the POD Jumper Cable This appliance is equipped with an “On Demand” intermittent pilot 1). Access the control box. ignition system (IPI) which also includes a continuous pilot ignition (CPI) mode with an integrated seven day timer. In IPI mode, the pilot will light before the main burner, when the appliance is turned on using a wall switch, remote or from a thermostat. -
Page 56: Troubleshooting
4. Check and make sure the ground wire from the pilot is connected to the fireplace body. If your fireplace still does not operate correctly, consult your local Montigo dealer. All service and repairs should be performed by a qualified Technician. All spare parts, optional fans, and optional trim finishes are available from your local Montigo dealer. XG0226 - 042220... -
Page 57: Indoor Fireplace In Protected Outdoor Applications
Appendix Indoor fireplace in protected outdoor applications This fireplace may be installed into outdoor locations provided they are suitably protected from direct water impingement. However, all installation clearances in the appliance manual must be observed. Framing, Clearances to Combustibles, Mantel Heights, Facing Requirements, Venting Installation, etc. -
Page 58: Appendix A: Venting Terminations
Appendix Appendix A: Venting Terminations Covered Covered Alcove Detail Alcove Detail Vinyl Siding 2’ 2’ 2’ 2’ 17.5’’ 29.5’’ 11.5’’ 17’’ Must use Vinyl Siding Termination Shield Location Canada* USA** clearance to the termination frame above grade, veranda, porch, deck, or balcony 12 inches 12 inches clearance to top of doors or operable windows... -
Page 59: Appendix B: Warranty
Canada, Inc. (collectively referred to herein as "The Companies"), remain in its original place of installation to be valid. warrants the Montigo gas appliance (referred to herein as 'the If the components of the appliance covered by this warranty appliance') to be free from defects in materials and workmanship are found to be defective within the time frame stated (see The at the time of manufacture. -
Page 60: Appendix B: Warranty Continued
Montigo dealer (www.Montigo.com) or contact Montigo direct at techsupport@ montigo.com. Ensure you have your sales receipt and the model and serial number of your appliance. DO NOT ATTEMPT TO DO ANY SERVICE WORK YOURSELF If you cannot locate the installing dealer, or nearest dealer/ distributor, you must notify The Companies in writing. -
Page 61: Appendix C: Amendment
Appendix Appendix C: Amendment (Gas Fireplace / Equipment sold in the State of Massachusetts) 5.08: Modifications to NFPA-54, Chapter 10 (1) Revise NFPA-54 section 10.5.4.2 by adding a second exception as 4. INSPECTION. The state or local gas inspector of the side wall follows: horizontally vented gas fueled equipment shall not approve the installation unless, upon inspection, the inspector observes... -
Page 62: Drl3613*I Basic Exploded Parts
Appendix DRL3613*I BASIC Exploded Parts BASIC PARTS LIST PAGE 1 ITEM # PART # DESCRIPTION CBSDRL36 CEMENT BOARD ASSY RSCDRL3613 SCREEN ASSY RDTDRL3613 DOOR ASSEMBLY RVBDRL3613 VALVE COVER RBDRL3613 BURNER ASSEMBLY RPCDRL PILOT COVER REPLACMENT POWER RECA131 HARNESS RGC3089 VALVE RPA035 PILOT ASSY RRTDRL36... -
Page 63: Drl3613*I-2 Full Load Exploded Parts
Appendix DRL3613*I-2 FULL LOAD Exploded Parts PARTS LIST PAGE 1 ITEM # PART # DESCRIPTION CBSDRL36 CEMENT BOARD ASSY SCRIDRL36 SCREEN ASSY RDTDRL3613 DOOR ASSEMBLY RVBDRL3613 VALVE COVER RBDRL3613 BURNER ASSEMBLY RPCDRL PILOT COVER REC1546 REPLACMENT BULB ONLY RGC3089 VALVE RPA035 PILOT ASSY REC1377DRL... -
Page 64: Drl4813*I Basic Exploded Parts
Appendix DRL4813*I BASIC Exploded Parts BASIC PARTS LIST ITEM # PART # CBSDRL48 CEME RSCDRL4813 RDTDRL4813 RVBDRL4813 RBDRL4813 BURN RPCDRL BASIC PARTS LIST PAGE 1 REPLA RECA131 ITEM # PART # DESCRIPTION RGC3089 CBSDRL48 CEMENT BOARD ASSY RPA035 BASIC PARTS LIST RSCDRL4813 SCREEN ASSY RRTDRL48... -
Page 65: Drl4813*I-2 Full Load Exploded Parts
Appendix DRL4813*I-2 FULL LOAD Exploded Parts PARTS LIST PAGE 1 ITEM # PART # DESCRIPTION CBSDRL48 CEMENT BOARD ASSY SCRIDRL48 SCREEN ASSY RDTDRL4813 DOOR ASSEMBLY RVBDRL4813 VALVE COVER RBDRL4813 BURNER ASSEMBLY RPCDRL PILOT COVER REC1546 REPLACMENT BULB ONLY BLACK GLASS RGC3089 VALVE RPA035... -
Page 66: Drl6013*I Basic Exploded Parts
Appendix DRL6013*I BASIC Exploded Parts BASIC PARTS LIST ITEM # PART # CBSDRL48 CEME RSCDRL4813 RDTDRL4813 RVBDRL4813 RBDRL4813 BURN RPCDRL BASIC PARTS LIST PAGE 1 REPLA RECA131 ITEM # PART # DESCRIPTION RGC3089 CBSDRL48 CEMENT BOARD ASSY RPA035 BASIC PARTS LIST RSCDRL4813 SCREEN ASSY RRTDRL48... -
Page 67: Drl6013*I-2 Full Load Exploded Parts
Appendix DRL6013*I-2 FULL LOAD Exploded Parts PARTS LIST PAGE 1 ITEM # PART # DESCRIPTION CBSDRL48 CEMENT BOARD ASSY SCRIDRL48 SCREEN ASSY RDTDRL4813 DOOR ASSEMBLY RVBDRL4813 VALVE COVER RBDRL4813 BURNER ASSEMBLY RPCDRL PILOT COVER REC1546 REPLACMENT BULB ONLY BLACK GLASS RGC3089 VALVE RPA035... -
Page 68: Drl7213*I Basic Exploded Parts
Appendix Part DRL7213*I BASIC Exploded Parts PROFLAME2 B BATTE PROFLA PROFLAME PILOT POWERVENT H LP CO ADJUSTABLE ADJUSTABLE T DELRAY POWERV DELRAY THE DELR ADJUST FASTEN Part description Part number ADJUSTA REAR CEMENT BOARD CBSDRL72 SIDE DELRA SCREEN RSCDRL7213 BBLACK G DOOR RDTDRL7213 ROCK TRAY... -
Page 69: Drl7213*I-2 Full Load Exploded Parts
Appendix Part description CEMENT BOARD MICRO MESH SCREE DRL7213*I-2 FULL LOAD Exploded Parts DOOR Part descri ROCK TRAY CEMENT BO VALVE BLIND MICRO MESH S HI-LO BURNER DOOR PILOT ROCK TRA VALVE VALVE BLI PILOT COVER HI-LO BUR REPLACEMENT BULB PILOT LEFT FAN VALVE... - Page 70 Installation & Maintenance Manual V 1.3 DelRay DelRay Single Sided Gas Fireplace Single Sided Gas Fireplace XG0226 - 042220...