Mitsubishi Electric 800 Series Instruction Manual page 133

 Dedicated motor (SF-V5RU(H)) outline dimension drawings (standard
horizontal type with brake)
Frame number: 90L
Connector (for encoder)
MS3102A20-29P
Terminal box for cooling fan
L
A
Exhaust
Suction
*1
*2
Direction of
Mark for earthing
cooling fan wind
(grounding)
Sliding distance
W
X
S Frame leg viewed
from above
Section AA
Main terminal box
For brake (B1, B2)
For motor (U, V, W)
For thermal protector (G1, G2)
B1 B2 U V W G1 G2
Earthing (grounding)
terminal (M4)
Dimensions table (Unit: mm)
SF- SF- SF-
SF-
V5R V5R V5R
V5R Fram Mass
U U U
U e No. (kg)
[]K1 []K3 []K4
[]KB
B B B
1 — — — 90L 29 296.5 114
2 1 — — 100L 46 333.5 128 100 207
3 2 1 — 112M 53
5 3 2 — 132S 70
NOTE
• Install the motor on the floor and use it with the shaft horizontal.
• Leave an enough clearance between the fan suction port and wall to ensure adequate cooling. Check that a fan blows air from
the opposite load side to the load side.
• The vertical tolerance for the shaft center height is
• The 400 V class motor has "H" in its model name.
• Since a brake power device is a stand-alone, install it inside the enclosure. (This device should be arranged by the customer.
Refer to the FR-E800 catalog.)
132
4. Specifications
4.4 Outline dimension drawings
R
KL
KA B
50
Main
40
terminal box
A
A
XB
2
F F E
N
Earth (ground)
terminal (M5)
Terminal box for cooling fan
For cooling fan (A, B)
A B C
Earthing (grounding)
terminal (M4)
A B C D E F G H
90 183.6 70 62.5 4 — —
80 70 6.5 — —
355 135 112 228 95 70 6.5 — —
416 152 132 266 108 70 6.5 — —
Frame number: 100L, 112M, 132S, 132M
Connector (for encoder)
MS3102A20-29P
Terminal box for cooling fan
D
Suction
*1
1
*2
Direction of
cooling fan wind
Mark for earthing
E
(grounding)
M
Earth (ground)
terminal (M5)
* indicates an inserting position of a bolt with hex head holes for manual
opening.
Make sure to earth the earth terminal of the flange section as well as
the earth terminal in the terminal box.
Motor
I J KA KD KG KL KP L M ML N
— 53 27 65 220 245 465 175 — 150 15
40 65 27 78 231 265 526.5 200 212 180
40 69 27 93 242 290 555 230 242 180
40 75 27 117 256 329 655 256 268 180
0 .
-0.5
L
KL
A R
B Q
KA
Main
Exhaust QK
terminal box
A
A
F F XB
N
W
S
Section AA
Shaft end
X XB Z Q QK R S T U
56 9 50 40 168.5 24j6 7 4
4 63 12 60 45 193 28j6 7 4
4 70 12 60 45 200 28j6 7 4
4 89 12 80 63 239 38k6 8 5
D
*1
*2
J
E E
M
ML
Sliding distance
X
Frame leg viewed
from above
Terminal screw size
U, V, A, B, G1, B1,
W
W (C) G2 B2
8 M6 M4 M4 M4
8 M6 M4 M4 M4
8 M6 M4 M4 M4
10 M6 M4 M4 M4