Field Wiring; Wiring Overview - Zeta Alarm Systems SMARTCONNECT SMART6 Installation Manual

Smart Connect Multi-loop Installation Manual
Check that the module configuration is as expected using the  and  to navigate the through the port numbers. Press the
1.
✓icon to confirm the changes.
2. The new module is now configured into the panel and is ready for use.
3. Since the batteries are not connected, the panel will report them as removed, lighting the yellow "Fault" LED, intermittently
sounding the fault buzzer, and displaying battery removed message on the screen.
4. Connect the batteries, ensuring that the polarity is correct (Red wire = +ve) & (Black wire = -ve). Acknowledge the fault event
via the display screen, and reset the panel to clear the battery fault.
5. The panel should now remain in the normal condition, and you can configure the panel as normal.

Field Wiring

NOTE: The terminal blocks are removable to make wiring easier.
ATTENTION: DO NOT EXCEED POWER SUPPLY RATINGS, OR MAXIMUM CURRENT RATINGS.

Wiring Overview

NEUTRAL (Blue)
EARTH (Green)
LIVE (Brown)
(Supervised)
AUX POWER B
Regulated 28V DC @ 1A
AUX POWER A
Regulated 28V DC @ 1A
BLACK
-
+
NEG POS
BATTERY CABLE: OBSERVE POLARITY
RED +
BLACK -
NOTE: The Smart Connect Multi-loop panel is a modular system, where any module can be
connected to any
illustrative purposes.
www.zetaalarmsystems.com
A
A
A
A
A+ A- B+B-
MAINS FUSE
Fuse F
AC: 120 VAC 50/60 Hz SCM -LCM S CM -A CM
240 VAC 50/60 Hz
AC Power ON
DC Power ON
Charger Trouble
Battery Trouble
Battery Hi Z Trouble
Fuse Trouble
SIG NALS SIG NALS
NO
CM
NC
NO
CM
NC EOLR EOLR
4k7 4k7
P OWER CONNECTIONS 3 0 V D C
+
-
+
C
-
+
-
+
-
+ - + - + - + - + - + -
BATTERY
I/P1 I/P2 I/P3 I/P4 I/P5 I/P6
Fuse E
SCM-MIM
- -
+ +
- +
Do not short circuit
battery terminals
(Supervised)
RED
-
+
NEG POS
(Not Supervised)
expansion port. The above diagram gives an example configuration for
The panel has detected no module changes, so has
powered up and started running
EOLR
EOLR EOLR EOLR
4k7
4k7 4k7 4k7
C C C
C C C
C C C
C C C
+ - + - + - + - + - + - + - + -
NAC1 NAC2
ZM1 ZM2 ZM3 ZM4 ZM5 ZM6
SCM-ZMM
EOLR
(Supervised)
4k7
To Previous To Next
Network Panel Network Panel
C C
PROGRAMMABLE RELAYS
DRY CONTACT (NOT-SUPERVISED)
RATED @ 5A, 250V RESISTIVE
NO C NC NO C NC NO C NC A B S C N A B S C N
O/P1 O/P2 O/P3 NET 1 NET 2
SCM-RM SCM-NM SCM-PM
Tr ouble Out put (N or m al Stat us )
* Clos e B et ween N / C and CM
* Open B et ween N / O and CM
A lar m Out put (N or m al Stat us )
* Clos e B et ween N / C and CM
* Open B et ween N / O and CM
Addressable Detector
A
A
Addressable Interface
Sounder
Conventional Detector
C
Cable To Printer
No User Wiring
Dry Contact Switch / Relay
C
(Not Supervised)
22