Leak Detect (Drain) Error; Water Leak Detect (Fill) Error; Suds Lock Error; Broken Belt Error - ALLIANCE Speed Queen Programming

•
Press the keypad three (3) times in a period of five (5) sec-
onds.
• Cycle the power to the machine.
•
Open the access panel and press the
This method will also list the error messages on the display.
The control saves the error type and adds the error to the last 25
errors queue.
The default slow drain time is 105 seconds for a pump and 18
seconds for a gravity drain.
There is a second slow drain programmable parameter: The Slow
Drain Detection Adjust Value. This parameter may be program-
med from 0 to 255 seconds (default is 0 seconds). This value is
added to the value found in the non-programmable data table
stored in the control, which contains an acceptable drain time for
each machine size and type.

Leak Detect (Drain) Error

If during a Water Leak Diagnostic Test the water level has low-
ered more than an acceptable amount, the control will save a wa-
ter leak error status and will continue the machine cycle. Immedi-
ately upon detecting the error the Error Status Indicator will ap-
pear on the control's diplay. When the cycle has completed, and
the door is opened or any keypad is pressed, the Machine Error
Tone will sound for 15 seconds and the control will display
"LEAK DETECT (DRAIN) ERROR" for one minute or until any
keypad has been pressed.
The Error Status Indicator will re-appear in the upper left corner
of the control's display after the one (1) minute error message has
expired. The Error Status Indicator can be cleared in one of the
following ways.
•
Press the keypad three (3) times in a period of five (5) sec-
onds.
• Cycle the power to the machine.
•
Open the access panel and press the
This method will also list the error messages on the display.
The control saves the error type and adds the error to the last 25
errors queue.

Water Leak Detect (Fill) Error

If during a Water Leak Diagnostic Test the water level has raised
more than an acceptable amount, the control will save a water
leak error status and will continue the machine cycle. Immediate-
ly upon detecting the error the Error Status Indicator will appear
on the control's display.
When the cycle has completed, and the door is opened or any
keypad is pressed, the Machine Error Tone will sound for 15 sec-
onds and the control will display "WATER LEAK DETECT
(FILL) ERROR" for one (1) minute or until any keypad has been
pressed.
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
The Error Status Indicator will re-appear in the upper left corner
of the control's display after the one (1) minute error message has
expired. The Error Status Indicator can be cleared in one of the
following ways.
for three (3) seconds.
•
•
•
The control saves the error type and adds the error to the last 25
errors queue.

Suds Lock Error

This error can be programmed on or off. It is on by default. The
control will check for suds whenever it is in a spin step. If the
control determines that there are suds in the machine based on the
conditions noted in the Suds Removal Routine, and has already
done the maximum number of programmed Suds Removal Rou-
tines, it will save a Suds Lock Error. The control will also limit
the speed to a maximum of 90 RPMs for the rest of the cycle.
When the cycle has been completed, if the control has saved a
Suds Lock Error and the Suds Lock Error display is enabled, the
control will display "SUDS LOCK ERROR" after the door is
opened or a key is pressed. The control will continue displaying
"SUDS LOCK ERROR" until any keypad has been pressed or for
one (1) minute.
The control saves the error type and adds the error to the last 25
errors queue.

Broken Belt Error

The control will perform a check on the Broken Belt communica-
tion from the drive/output board every 10 milliseconds. If the
Broken Belt communication is ever set, the control will display
"BROKEN BELT ERROR". The control will turn off all outputs
for three (3) seconds.
and turn on Machine Error Tone for 15 seconds.
After 15 seconds, the control will continue to show the error dis-
play. If a keypad is pressed before 15 seconds have elapsed, the
control will turn off the Machine Error Tone. When this error oc-
curs, the audit counter for the error is incremented in the machine
error audit data section and added to the last 25 errors queue.
To clear this error the machine must be powered down, the Clear
Fatal Error Keys must be pressed, or a Clear Fatal Error Network
command must be sent.

Door Lock Error (Fatal)

If the door unlocks while running a cycle, the control will enter
Machine Error Mode. The control will turn off all outputs, dis-
play "DOOR LOCK ERROR", and turn on the Machine Error
Tone for 15 seconds to indicate a door lock/unlock error.
75
Press the keypad three (3) times in a period of five (5) sec-
onds.
Cycle the power to the machine.
Open the access panel and press the
This method will also list the error messages on the display.
Machine Errors
for three (3) seconds.
Part No. 806526ENR2