Advance To Drain And Spin - ALLIANCE AWN43RSN115CW01 Instruction Manual

Hide thumbs

Table Of Contents

Table of Contents

Lid Switch Test

This step verifies that the Lid Switch is correctly wired and work-

ing. Close the lid. When the lid switch is closed, the SPIN and

LID LOCK LEDs will be lit.

Close the lid and press Start/Pause button to exit the step.

Hot Fill Test

This step checks the hot water valve. The WASH LED is on dur-

ing this test. The valves will shut off once two inches of water

has been reached.

Press Start/Pause button to advance to the next step.

Cold Fill Test

This step checks the cold water valve. The RINSE LED is on dur-

ing this test. The valves will shut off once three inches of water

has been reached.

Press Start/Pause button to advance to the next step.

Pressure Sensor Fill Test

This step checks the water level input. All water valves will be on

until the low water fill level is satisfied (four inches). The WASH

and RINSE LEDs will be lit in this step.

Press Start/Pause button once the water level is satisfied to exit

the step.

Lid Lock Test

This step checks the Lid Lock input. When the step is entered, the

control will lock the lid. It will check to make sure the lid is

locked and if it is, the LID LOCK LED will be on, otherwise the

LID LOCK LED will flash.

Once locked, press Start/Pause button to exit the step.

Long Stroke Agitate Test

In Software Version 3 and higher this is skipped.

Not available on models through Serial Nos. beginning 1810.

This step checks the Low Agitate speed. The WASH and SPIN

LEDs are On, the Cycle Run Output is on, and the machine enters

a Delicate Cycle Long agitate.

The control will remain in this step until the Start/Pause button is

pressed.

Short Stroke Agitate Test

In Software Version 3 and higher this is skipped.

Not available on models through Serial Nos. beginning 1810.

This step checks the Regular Agitate speed. The RINSE and

SPIN LEDs are on and the machine enters a Delicate Cycle Short

agitate.

DO NOT COPY or TRANSMIT

The control will remain in this step until the Start/Pause button is

pressed.

Factory Spin Test

This step checks the spin speeds. The machine steps through spin

speeds and maintains each speed for a few seconds. After 820

RPM, the motor will stop. All OBL checking is done and if either

the out of balance switch is hit or the OBL check fails at 300

RPM, the time will be reset indefinitely to allow the load to be

rebalanced so that it can spin up and reach full speed.

The control will advance to the next step if the Start/Pause button

is pressed at any time during this step.

During this step, if 300 RPM is reached, the WASH LED will be

lit. If 500 RPM is reached, the RINSE LED will be lit. If 820

RPM is reached, the SPIN LED will be lit and if 800 RPM is

reached, the LID LOCK LED will be lit to indicate that a passing

speed has been reached.

All water valves will be on during this entire test to blow them

out.

Unbalance Switch Test

This step checks that the unbalance switch is working. The

WASH and RINSE LEDs will be on during the entire test. When

the switch is pressed, the SPIN and LID LOCK LEDs will be on.

The switch must be pressed and then Start/Pause button can be

pressed to advance to the next step.

Breakaway Test

This step checks the lid unlock function. All valves will be open

at the beginning of this step to allow the blowing out of the

valves, if needed. The Start/Pause button must be pressed to start

exiting the test. The first Start/Pause press will turn off the water

valves and start the unlock process. Once the lid unlocks, the ma-

chine will exit the test.

The RINSE and SPIN LEDs will be lit during this test. The LID

LOCK LED will be lit when the lid is locked in this test.

Power Down Test

This is the final step of the factory test procedure. All LEDs will

be off to signify that the factory test procedure has been complet-

ed and that the user can safely unplug the machine. Cycling pow-

er to the machine is the only way to resume normal operation.