Set-Up Menu 6 (Analog Output Set-Up) - Mitsubishi Electric ME96NSR Operator's Manual

■ Set-up Menu 6 (Analog Output Set-up)

In the operation mode, press
SET
The set-up screen can be displayed for measurement items that are not selected in display pattern.
When the ME-4201-NS96 type optional plug-in module is not installed, this menu cannot be set.
Set the set-up menu number to "6".
+ –
,
Set-up menu
DISPLAY SET
① Analog output CH1
+ –
,
measurement item
② Detailed analog output set-up
DISPLAY SET
(1) When A, DA are set (6.1.1)
to
(2) When W, var are set
② Analog output CH1
+ –
,
detailed set-up
(3) When PF is set
DISPLAY SET
(4) When Hz is set
to
③ Analog output CH2 to ③ Analog output CH2 to CH4 measurement item set-up
+ –
,
CH4 measurement
Analog outputs CH2 to CH4 are set also in the same method as
item
DISPLAY SET
to
④ Analog output
④ Analog output CH2 to CH4 detailed set-up
+ –
,
CH2 to CH4
detailed set-up Analog outputs CH2 to CH4 are set also in the same manner as
DISPLAY SET
⑤ Setting of the analog output limit.
Set to cut undefined analog output.
+ –
,
on : Cut undefined analog output.
⑤ Analog output limit
oFF : Don't cut undefined analog output.
DISPLAY SET
According to the set-up diagram (page 6), save the changed contents or continue to the other set-up menu.
+ –
,
Set-up menu
and simultaneously for 2 seconds or more, and the following operation becomes available.
RESET
• Current value is set to the maximum output value of
analog output.
It can be set in the range of about 40% to about 120%
of ratings.
As for detailed set values, refer to the user's manual.
• Power value and reactive power value are set to the
maximum output value of analog output. (6.1.1)
It can be set in the range of about 20% to about 120%
of ratings.
As for detailed set values, refer to the user's manual.
• In the case of W, set to the single/double deflection.
(initial content : single deflection) (6.1.2)
Example of power 1000W
mA mA
Single deflection Double deflection
20 20
12
4 4
0
–1000W
1000W 0 1000W
• The power factor value to the maximum output value of
analog output CH1 is set from – 0 .5 – 1 – 0 .5/ – 0 – 1
mA mA
20 20
12 12
4 4
– 0.5 1 0.5 – 0 1
• The frequency range of analog output is set.
60Hz 50Hz
Note: When it is set to 50Hz, output is made at span 45 to 55Hz.
When it is set to 60Hz, output is made at span 55 to 65Hz.
These settings can be set separately from measurement
items.
① Set the measurement item for analog output CH1.
Select measurement element output from below.
Three phase 3-wire
– 0
0
➀
analog output CH1 measurement item set-up.
➁
analog output CH1 detailed set-up.
Setting
on
oFF
Three phase 4-wire
non non
A A
1 1
A A
2 2
A A
3 3
A :CH1 A
AVG N
DA A :CH1
1 AVG
DA DA
2 1
DA DA
3
2
DA DA
AVG 3
V DA
12 N
V DA
23 AVG
V V
31 1N
V :CH2 V
LLAVG 2N
Σ
W:CH3 V
3N
Σ
var V :CH2
LNAVG
Σ
PF:CH4 V
12
Hz V
23
V
HI
1 31
HI V
2 LLAVG
HI W
1
3
W
HV
12 2
HV W
23 3
Σ
W:CH3
var
1
var
2
var
3
Σ
var
VA
1
VA
2
VA
3
Σ
VA
PF
1
PF
2
PF
3
Σ
PF:CH4
Hz
HI
1
HI
2
HI
3
HI
N
HV
1N
HV
2N
HV
3N
Output Range
Span of −1% to 101%
Span of −5% to 105%
11