AMQ ILINE Series Installation Manual
  1. Manuals
  2. Brands
  3. AMQ Manuals
  4. Indoor Furnishing
  5. ILINE Series
  6. Installation manual

AMQ ILINE Series Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ILINE installation guide

Advertisement

Table of Contents
loading

Related Manuals for AMQ ILINE Series

Summary of Contents for AMQ ILINE Series

  • Page 1 ILINE installation guide...

  • Page 2: Table Of Contents

    CONTENTS ILINE 180° (2-WAY) ASSEMBLY . . . . . . . . . . . . . . . 3 ILINE 90°/180° (4-WAY) ASSEMBLY . . . . . . . . . . . 30 Components .

  • Page 3: Iline 180° (2-Way) Assembly

    ILINE 180° (2-WAY)

  • Page 4: Components

    COMPONENTS ILINE 180° (2-WAY) 180° Post is for inline/2-way applications only 2-Way Post Top Cap Base Plate Post Side Cover Vertical Post Nuts Feet Assembly Beam Horizontal Beam Face Plate Cover Sliding Clip Receptacle Data Face Plate Data Adaptor Cover Junction Bracket Junction Bracket Bottom Beam Plate...

  • Page 5: Post, Beam Plate & Feet Assembly

    PHASE 1 | Post, Beam Plate & Feet Assembly ILINE 180° (2-WAY) Step 1 Step 2 amqsolutions.com ILINE INSTALLATION GUIDE | 5...

  • Page 6: Beam Assembly (3-Circuit)

    PHASE 2 | Beam Assembly (3-Circuit) ILINE 180° (2-WAY) Step 1 Step 2 Place beam upside down on the floor to reveal the Insert the sliding clip into the beam from the top beam canal. and slide it to the sides. (Make sure the tab below the clip goes into the slot on the beam.) amqsolutions.com ILINE INSTALLATION GUIDE | 6...
  • Page 7 PHASE 2 | Beam Assembly (3-Circuit) ILINE 180° (2-WAY) Step 3 Mount 2 receptacle on one side of the junction block. Insert the junction block slighfly tilted like in the diagram with the junction block without the receptacles facing the beam cut-out. Beam Cut-Out Side Step 4 Step 5...

  • Page 8: Beam Assembly (4-Circuit)

    PHASE 2 | Beam Assembly (4-Circuit) ILINE 180° (2-WAY) Step 1 Step 2 Place beam upside down on the floor to reveal the Insert the sliding clip into the beam from the top beam canal. and slide it to the sides. (Make sure the tab below the clip goes into the slot on the beam.) amqsolutions.com ILINE INSTALLATION GUIDE | 8...
  • Page 9 PHASE 2 | Beam Assembly (4-Circuit) ILINE 180° (2-WAY) Step 3 Mount 2 receptacle on one side of the junction block. Insert the junction block slighfly tilted like in the diagram with the junction block without the receptacles facing the beam cut-out. Beam Cut-Out Side Step 4 Step 5...

  • Page 10: Post, Beam Plate & Feet Assembly (Cont.)

    PHASE 1 | Post, Beam Plate & Feet Assembly (cont .) ILINE 180° (2-WAY) NOTE: Inner-to-Inner beams are slightly longer than Outer-to-Inner beams. NOTE: L-shaped configurations must use Inner-to-Inner beam. Step 1 Step 3 Once complete, lay each beam assembly between Slide the beam assemblies onto each of the each foot assembly.
  • Page 11 PHASE 1 | Post, Beam Plate & Feet Assembly (cont .) ILINE 180° (2-WAY) Step 4 Take the exposed end of the power entry and feed through the desired end of the beam and into the adjacent post-opening. Continue to feed the power entry until the exposed end is out through one of the base plate’s openings.
  • Page 12 PHASE 2 | Post, Beam Plate & Feet Assembly (cont .) ILINE 180° (2-WAY) Step 1 Step 3 Connect power entry plug to the junction block. Connect the jumper to each junction block. Step 2 Step 4 Feed the jumper through the beam canal and Repeat Steps 1-3 until the last jumper is connected into the vertical post opening into the next beam the last junction block.
  • Page 13 PHASE 3 | Post, Beam Plate & Feet Assembly (cont .) ILINE 180° (2-WAY) Step 1 Step 2 Insert side covers into all exposed openings of Place top caps on all vertical posts. each vertical posts. Step 3 Step 4 Take two data adapters/face plates and snap Insert the bottom beam plates between each data them onto each end of the underside of the beam...
  • Page 14 PHASE 4 | Post, Beam Plate & Feet Assembly (cont .) ILINE 180° (2-WAY) Step 1 Check the horizontal alignment of the beams Step 2 If not aligned, please rotate the foot to adjust each post’s elevation until leveled. NOTE: Use a leveling guide for accuracy.

  • Page 15: Iline 120° (3-Way) Assembly

    ILINE 120° (3-WAY)

  • Page 16: Components

    COMPONENTS ILINE 120° (3-WAY) 3-Way Post Top Cap Post Side Cover Hex Nuts Vertical Post Base Plate Glide,OEM 4-Way Post Top Cap Post Side Cover Hex Nuts Base Place Kit Post Sleeve Vertical Post Foot SRE Foot SRC Foot DRE Foot DRC amqsolutions.com ILINE INSTALLATION GUIDE | 16...
  • Page 17 COMPONENTS ILINE 120° (3-WAY) Beam Horizontal Beam Face Plate Cover Sliding Clip Receptacle Cover Data Face Plate Data Adaptor Junction Bracket Junction Bracket (3 circuit) (4 circuit) Bottom Beam Plate amqsolutions.com ILINE INSTALLATION GUIDE | 17...

  • Page 18: Post, Beam Plate & Feet Assembly

    PHASE 1 | Post, Beam Plate & Feet Assembly ILINE 120° (3-WAY) Step 1 Step 2 amqsolutions.com ILINE INSTALLATION GUIDE | 18...

  • Page 19: Beam Assembly (3-Circuit)

    PHASE 2 | Beam Assembly (3-Circuit) ILINE 120° (3-WAY) Step 1 Step 2 Place beam upside down on the floor to reveal the Insert the sliding clip into the beam from the top beam canal. and slide it to the sides. (Make sure the tab below the clip goes into the slot on the beam.) amqsolutions.com ILINE INSTALLATION GUIDE | 19...
  • Page 20 PHASE 2 | Beam Assembly (3-Circuit) ILINE 120° (3-WAY) Step 3 Mount 2 receptacle on one side of the junction block. Insert the junction block slighfly tilted like in the diagram with the junction block without the receptacles facing the beam cut-out. Beam Cut-Out Side Step 4 Step 5...

  • Page 21: Beam Assembly (4-Circuit)

    PHASE 2 | Beam Assembly (4-Circuit) ILINE 120° (3-WAY) Step 1 Step 2 Place beam upside down on the floor to reveal the Insert the sliding clip into the beam from the top beam canal. and slide it to the sides. (Make sure the tab below the clip goes into the slot on the beam.) amqsolutions.com ILINE INSTALLATION GUIDE | 21...
  • Page 22 PHASE 2 | Beam Assembly (4-Circuit) ILINE 120° (3-WAY) Step 3 Mount 2 receptacle on one side of the junction block. Insert the junction block slighfly tilted like in the diagram with the junction block without the receptacles facing the beam cut-out. Beam Cut-Out Side Step 4 Step 5...

  • Page 23: Footer & Base Plate Assembly

    PHASE 1 | Footer & Base Plate Assembly ILINE 120° (3-WAY) Step 1 Insert a 3” bolt into each of the 2” compression springs. Step 2 Insert the bolts and the - 4” x 3” Bolt (5/16” x 18) compression springs into the inner corner holes of the base plate.
  • Page 24 PHASE 2 | Footer & Base Plate Assembly ILINE 120° (3-WAY) amqsolutions.com ILINE INSTALLATION GUIDE | 24...

  • Page 25: Post & Beam Assembly

    PHASE 3 | Post & Beam Assembly ILINE 120° (3-WAY) Step 1 Step 2 Assemble the base plate, glide and post together. Slide the beam assembly into the open slots in the center of vertical post. Fasten the beams using two screws on each end.

  • Page 26: Entering Electric Base Feed

    PHASE 4 | Entering Electric Base Feed ILINE 120° (3-WAY) 7/16” Spanner Use 1/4”-20 hex nut to tight down posts on the footer-assemblies Step 1 Step 2 Take the exposed end of the power entry and feed Plug the power entry plug to the junction block. through the center vertical post.

  • Page 27: Cover And Trim Assembly

    PHASE 5 | Cover and Trim Assembly ILINE 120° (3-WAY) & Step 1 Step 3 Insert side covers into each exposed opening in Snap on data face plates onto each end of the vertical posts. beam assemblies. Step 2 Step 4 Attach top cover to the center vertical post.

  • Page 28: Installing Caps & Covers - Post Sleeve

    PHASE 6 | Installing Caps & Covers — Post Sleeve ILINE 120° (3-WAY) Step 1 Detach the pre-cut portion for the base feed access and line up with post. Step 2 Align the Post Sleeve* on both sides and apply pressure until pieces snap into place. Step 3 Installed Post Sleeve.

  • Page 29: Extending The Configuration

    PHASE 7 | Extending the Configuration ILINE 120° (3-WAY) Step 1 Step 3 Selecting the post that will accommodate the Feed the jumper through the beam canal and extension, replace the end foot plate (DRE) with a into the vertical post opening into the next beam center foot.

  • Page 30: Iline 90°/180° (4-Way) Assembly

    ILINE 90°/180° (4-WAY)

  • Page 31: Components

    COMPONENTS ILINE 90°/180° (4-WAY) 4-Way Post Top Cap Post Side Cover Hex Nuts Base Place Kit Post Sleeve Vertical Post Foot SRE Foot SRC Foot DRE Foot DRC amqsolutions.com ILINE INSTALLATION GUIDE | 31...
  • Page 32 COMPONENTS ILINE 90°/180° (4-WAY) Beam Horizontal Beam Face Plate Cover Sliding Clip Receptacle Cover Data Face Plate Data Adaptor Junction Bracket Junction Bracket (3 circuit) (4 circuit) Bottom Beam Plate amqsolutions.com ILINE INSTALLATION GUIDE | 32...

  • Page 33: Footer & Base Plate Assembly

    PHASE 1 | Footer & Base Plate Assembly ILINE 90°/180° (4-WAY) Step 1 Insert a 3” bolt into each of the 2” compression springs. Step 2 Insert the bolts and the compression springs into the - 4” x 3” Bolt (5/16” x 18) inner corner holes of the base plate.
  • Page 34 PHASE 2 | Footer & Base Plate Assembly ILINE 90°/180° (4-WAY) amqsolutions.com ILINE INSTALLATION GUIDE | 34...

  • Page 35: Beam Assembly (3-Circuit)

    PHASE 2 | Beam Assembly (3-Circuit) ILINE 90°/180° (4-WAY) Step 1 Step 2 Place beam upside down on the floor to reveal the Insert the sliding clip into the beam from the top beam canal. and slide it to the sides. (Make sure the tab below the clip goes into the slot on the beam.) amqsolutions.com ILINE INSTALLATION GUIDE | 35...
  • Page 36 PHASE 2 | Beam Assembly (3-Circuit) ILINE 90°/180° (4-WAY) Step 3 Mount 2 receptacle on one side of the junction block. Insert the junction block slighfly tilted like in the diagram with the junction block without the receptacles facing the beam cut-out. Beam Cut-Out Side Step 4 Step 5...

  • Page 37: Beam Assembly (4-Circuit)

    PHASE 2 | Beam Assembly (4-Circuit) ILINE 90°/180° (4-WAY) Step 1 Step 2 Place beam upside down on the floor to reveal the Insert the sliding clip into the beam from the top beam canal. and slide it to the sides. (Make sure the tab below the clip goes into the slot on the beam.) amqsolutions.com ILINE INSTALLATION GUIDE | 37...
  • Page 38 PHASE 2 | Beam Assembly (4-Circuit) ILINE 90°/180° (4-WAY) Step 3 Mount 2 receptacle on one side of the junction block. Insert the junction block slighfly tilted like in the diagram with the junction block without the receptacles facing the beam cut-out. Beam Cut-Out Side Step 4 Step 5...

  • Page 39: Post, Beam Plate & Feet Assembly

    PHASE 1 | Post, Beam Plate & Feet Assembly ILINE 90°/180° (4-WAY) NOTE: Inner-to-Inner beams are slightly longer than Outer-to-Inner beams. NOTE: L-shaped configurations must use Inner-to-Inner beam. Step 1 Step 3 Once complete, lay each beam assembly between Slide the beam assemblies onto each of the each foot assembly.
  • Page 40 PHASE 1 | Post, Beam Plate & Feet Assembly ILINE 90°/180° (4-WAY) Step 4 Take the exposed end of the power entry and feed through the desired end of the beam and into the adjacent post-opening. Continue to feed the power entry until the exposed end is out through one of the base plate’s openings.

  • Page 41: Installing Jumpers

    PHASE 2 | Installing Jumpers ILINE 90°/180° (4-WAY) Step 1 Step 3 Connect power entry plug to the junction block. Connect the jumper to each junction block. Step 2 Step 4 Feed the jumper through the beam canal and Repeat Steps 1-3 until the last jumper is connected into the vertical post opening into the next beam the last junction block.

  • Page 42: Installing Caps & Covers

    PHASE 3 | Installing Caps & Covers ILINE 90°/180° (4-WAY) Step 1 Step 2 Insert side covers into all exposed openings of Place top caps on all vertical posts. each vertical posts. Step 3 Step 4 Take two data adapters/face plates and snap Insert the bottom beam plates between each data them onto each end of the underside of the beam adapter on the underside of the beam assembly.

  • Page 43: Installing Caps & Covers - Post Sleve

    PHASE 4 | Installing Caps & Covers — Post Sleeve ILINE 90°/180° (4-WAY) Step 1 Detach the pre-cut portion for the base feed access and line up with post. Step 2 Align the Post Sleeve* on both sides and apply pressure until pieces snap into place. Step 3 Installed Post Sleeve.

  • Page 44: Installing Screens

    PHASE 5 | Installing Screens ILINE 90°/180° (4-WAY) NOTE: Pre-measuring each clip’s distance from the beam ends before attaching will ensure a centered and balanced appearance to the installed screen. (Suggested distance between clip and beam edge: 11 inches.) NOTE: For 22”...

  • Page 45: Final Adjustments

    PHASE 6 | Final Adjustments ILINE 90°/180° (4-WAY) H o r i z o n t a l a l i g e n t * Adjust height of each coupling-nuts to level the base plate of each post. Step 1 Step 2 Check the vertical and horizontal alignment of the If not aligned, use a 1/2”...

  • Page 46: Power Pole Retrofit

    PHASE 7 | Power Pole Retrofit ILINE 90°/180° (4-WAY) Step 1 Step 3 Mount the adapter bracket to power pole using two Anchor down the post with two screws into the machine screws and two self tappers. vertical post. Step 2 Step 4 Insert Power Pole with adapter bracket into the slot Adjust glide in the bottom plate to the floor level.
  • Page 47 Please contact cc@amqsolutions.com if you are missing any parts, have difficulty with assembly, or have any product related questions.

This manual is also suitable for:

Iline 180 2-wayIline 120 3-wayIline 90/180 4-way

Table of Contents