Land Pride SB10 Series Operator's Manual page 24

Section 3: Tractor Hook-up & Unhook
6. Start tractor, raise implement slightly, and drive
forward enough to clear support blocks.
7. Lower implement to ground and shut tractor down
before dismounting. Refer to "The following are
basic power machine shutdown procedures.
Follow these procedures and any additional
shutdown procedures provided in your power
machine Operator's Manual before leaving the
operator's seat." on page 8.
8. Continue with "Hydraulic Hook-up" on page 20.
Hydraulic Hook-up
!
WARNING
To avoid serious injury or death:
Hydraulic fluid under high pressure can penetrate the skin
and/or eyes causing a serious injury. Wear protective gloves
and safety glasses or goggles when working with hydraulic
systems. Use a piece of cardboard or wood rather than hands
when searching for leaks. A doctor familiar with this type of
injury must treat the injury within a few hours or gangrene
may result. DO NOT DELAY.
Two Snow Blower options require hydraulic hose hook-
ups. They are hydraulic motor for chute rotation and
hydraulic cylinder for deflector angling. Be sure tractor
reservoir is filled properly before operating hydraulic
motor and/or hydraulic cylinder. If tractor reservoir is low
on hydraulic fluid, there is a chance of drawing air into the
system causing jerky or uneven movements.
Hydraulic Motor For Chute Rotation
1. Locate hydraulic motor hoses and connect quick
disconnect couplings to a single duplex outlet on the
tractor. This is best if connected to the control lever
closest to the operator.
2. Set tractor control lever in the non-float position.
3. Cycle hydraulic system by rotating chute until it points
o
to the left at 90 to the direction of travel and then
o
rotating chute a 180
this several times to purge hydraulic motor of air.
4. Switch quick disconnect couplings at the duplex
outlet if chute does not rotate in the direction desired.
It is best if chute rotates to discharge to the right
when pushing control lever on the tractor forward.
Hydraulic Cylinder For Deflector Adjustment
1. Locate hydraulic cylinder hoses and connect quick
disconnect couplings to a single duplex outlet on the
tractor. This is best if connected to the control lever
next to the hydraulic motor control lever.
2. Set tractor control lever in the non-float position.
NOTE: It is not necessary to purge the hydraulic
system of trapped air if operation is sluggish. The
cylinder is double acting and will self purge itself of
air as hydraulic oil cycles back and forth through the
cylinder several times.
20
SB1051, SB1064, SB1574, & SB2584 with S/N 881641+ Snow Blowers 370-430M
Table of Contents
in the opposite direction. Do
3. Cycle hydraulic system by extending and retracting
the cylinder several times to purge hydraulic cylinder
of air.
4. Switch quick disconnect couplings at the duplex
outlet if deflector does not angle in the direction
desired. It is best if deflector raises when pushing
control lever on the tractor forward.
Power
Terminal
White/Black
Deflector Terminal
Red/Black
Rotate Terminal
10 Amp fuse
Black Wire Red Wire
Negative (-) Positive (+)
Electrical Hook-up
Figure 3-7
Electrical Hook-up
Refer to Figure 3-7:
Two Snow Blower options require electrical hook-up.
They are electric motor for chute rotation and electric
actuator for operating the deflector angling.
1. Find a suitable location to mount control box (#1) on
the tractor. Usually this would be close to the
operator's right-hand side on the tractor fender or
fender console. Exact location should be convenient
for operating toggle switches (#2 & #3).
2. Route power cable eyelets (#10 & #11) to tractor
power source or circuit breaker panel. A 10 Amp or
larger fuse/circuit breaker source should be used.
a. Connect red lead (#10) to a 12 VDC positive (+)
power source.
b. Connect black lead (#11) to a negative (-) 12 VDC
power source.
3. Connect power cable terminal (#13) to control box
terminal (#4).
Deflector
White Toggle
Chute Rotate
Red Toggle
Control
Box Mount
Chute Rotate
Wire Harness
Deflector
Wire Harness
33291
1/23/19